PB TEEN Chelsea Platform Bed User manual

www.pbteen.com
D – Left Side Rail - 1 pc. E – Right Side Rail - 1 pc. F – Center Rail - 1 pc.
G – Slat Roll - 1 pc H – Support Rail - 2 pcs. I – Leg- 4 pcs. J – Center Leg- 1 pc.
Chelsea Platform Bed
Pre-assembly:
•Please read all instructions before
beginning assembly.
•Two-adult assembly is recommended.
•Save all packing materials until assembly
complete to avoid accidentally discarding
smaller parts or hardware.
Parts included:
B – Head Rail - 1 pc.
A – Storage - 1 pc. C – Foot Rail - 1 pc.

www.pbteen.com
K – Large Bolts (M8)- 8 pcs. M – Large Spring Washer(M8)- 8 pcs.
N – Small Spring Washer (M6)-12 pcs.
Q – Wood Screw - 32 pcs
L – Small Bolts (M6)- 12 pcs.
R – Iron Dowel - 12 pcs S – Large Allen Key (M8)- 1 pc
T – Small Allen Key (M6)- 1 pc
O – Large Flat Washer(M8)– 8 pcs. P – Small Flat Washer (M6)- 12 pcs
Hardware Included:
Tools required but not included:
Phillips Head Screwdriver
Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove all the parts from the boxes.
2. Determine the desired location of the piece and prepare all parts there before beginning assembly.
3. Assemble the Center Rail (F) to the Foot Rail (C) and the Head Rail (B) by inserting the pre-attached
wood dowel of the Center Rail (F) into the pre-drilled hole of the Foot Rail (C) and the Head Rail (B),
as shown below. Insert a Small Bolt (L) a Small Spring Washer (N) and a Small Flat Washer (P)
through the pre-drilled hole on the end of the Center Rail (F) and into the pre-drilled holes on the side
of the Foot Rail (C) and Head Rail (B), as shown in figure 1. Tighten with the Small Allen Key (T).
Fi
g
ure 1

www.pbteen.com
4. Assemble the Support Rail (H) to the middle of the Center Rail (F) by aligning the pre-attached wood
dowels on end of the Support Rail (H) and inserting them into the pre-dilled holes on the side of the
Center Rail (F) Insert a Small Bolt (L), Small Spring Washer (N) and Small Flat Washer (P) through
the pre-drilled hole on end side of the Support Rail (H), as shown in figure 2. Tighten with the Small
Allen Key (T)
5. Before assembling the Support Rail (H) to Right Side Rail (E), insert 3 Iron Dowels (R) into pre-drilled
holes to the end of Foot Rail (C) and another 3 Iron Dowels (R) to Head Rail (B) as shown in Figure
3.
Assemble the Support Rail (H) to Right Side Rail (E) by aligning the pre-attached wood dowels on the
end of Support Rail (H) and inserting them into the pre-dilled holes on Right Side Rail (E). NOTE:
Make sure to simultaneously align the 3 Iron Dowels (R) at the end of the Foot Rail (C) and the Head
Rail (B) with the pre-drilled holes in Right Side Rail (E) as shown in Figure 3. Insert a Small Bolt (L),
Small Spring Washer (N) and a Small Flat Washer (P) through the pre-drilled hole on end side of the
Support Rail (H) as shown in Figure 3.1. Tighten with the Small Allen Key (T)
Assemble the Right Side Rail (E) to the Foot Rail (C) by inserting a Large Bolt (K), a Large Spring
Washer (M), and a Large Flat Washer (O) through the pre-drilled holes of the Foot Rail (C) as shown
in Figure 3. Tighten using the Large Allen Key (S). Repeat to assemble Right Side Rail (E) to the
Head Rail (B). Tighten with the Large Allen Key (S).
Fi
g
ure 2
Fi
g
ure 3
Fi
g
ure 3.1

www.pbteen.com
6. Assemble the Left Side Rail (D) to the Foot Rail (C) and Head Rail (B) by inserting 3 Iron Dowels (R)
into the pre-drilled holes at the both end of Left Side Rail (D) as shown in figure 4. Insert a Large
Bolt (K) a Large Spring Washer (M) and a Large Flat Washer (O) through the pre-drilled holes of the
Foot Rail (C) and into the pre-drilled holes of the Head Rail (B). Tighten using the Large Allen Key
(S). Repeat this step to assemble the Left Side Rail (D) to Head Rail (B) as shown in the images
below.
Fi
g
ure 4

www.pbteen.com
7. Insert the exposed screw of the Leg (I) into the pre-drilled hole on each corner and the Center Leg (J)
on the middle of the Center Rail as shown in figure 5. Turn clockwise until tight.
8. Turn the Platform Bed upright and assemble the Storage (A) to the bed by placing the Storage (A)
onto the top of the Right Side Rail (E) and Center Side Rail (F), making sure to align the pre-drilled
holes of the Right Side Rail (E) and the Center Rail (F) with the pre-drilled holes on the underside of
the Storage (A). Insert a Small Bolt (L), a Small Spring Washer (N) and Small Flat Washer (P)
through the pre-drilled under the Right Side Rail (E) and into the pre-drilled holes of the Storage (A),
as shown in figure 6. Tighten with the Small Allen Key (T)
Fi
g
ure 5
Fi
g
ure 6

www.pbteen.com
9. Lay the Slat Roll (G) on the inner ledges of the Left Side Rail (D) and the Center Rail (F). Using a
Phillips Head Screwdriver, fasten the Slat Roll (G) onto the rails with 32 Wood Screw (Q), as shown
in figure 7. Do not fully tighten until all screws are in place.
10. Adjust the levelers on the bottom of all the Legs (I) and the Center Leg (J) so that bed is level on
the floor as shown in figure 7.1 and figure 7.2
Care Instructions:
•Avoid direct sunlight and excessive
temperatures.
•Dust often using a clean, soft, dry and lint-free
cloth.
•Slightly moisten cloth with water. A damp cloth
holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.
Fi
g
ure 7
Fi
g
ure 7.1 Fi
g
ure 7.2