peerless-AV SS560F Guide

ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Installation and Assembly:
Display Stand for 32" - 60" Flat Panel Displays
Models: SS560F
Max UL Load Capacity: 150 lb (68 kg)
Suitable For Institutional Use

2 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
Table of Contents
Parts List.................................................................................................................................................................................3
Assembling Floor Stand .........................................................................................................................................................4
Attaching Display using VESA 100, 200 or VESA 300 Mounting Pattern...............................................................................6
Mounting Flat Panel Display ..................................................................................................................................................8
Tools Needed for Assembly
• level
• phillips screwdriver
NOTE: Read entire instruction sheet before you start installation and assembly.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• Never exceed the Maximum UL Load Capacity on page 1. Use with heavier televisions may result in instability
causing tip over resulting in death or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The cart or stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand
is shaken or hit. Not recommended for use in areas with heavy traffic.
• Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control
or toys placed on the furnishing may encourage a child to climb on the furnishing resulting in the furnishing tipping
over on to the child.
• Relocating audio and/or video equipment from this cart or stand to furniture not specifically designed to support
audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning
onto a child.
WARNING

3 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
Some parts may appear slightly different than illustrated.
SS560F
Description Qty. Part #
A
base 1 009-1407
Bupright 1 009-1413
Cdisplay mounting bracket 1 201-1156
Dadapter plate 1 009-1599
Etop cover 1 590-1210
F3/8-16 x 2.5" button socket cap screw 3 520-9550
G1/4-20mm nut 6 530-1050
H1/4-20 x 12mm decorative screw 10 520-2325
I4mm allen wrench 1 560-9646
J7/32" allen wrench 1 560-9715
KM10 x .402 ID washe
r
3 540-9424
Parts List
CD
E
IJ F G
A
B
H
Before you begin, make sure all parts shown are included with your product.
K
Adapter Bracket Fasteners
M5 x 12 mm (4)
(520-1027)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M6 x 25 mm (4)
(520-1208)
.75" spacer (4)
(540-1059)
Multi-washer (4)
(580-1398)
M8 x 25 mm (4)
(520-1031)
M8 x 12 mm (4)
(520-9571)

4 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
1Attach upright (B) to base (A) with three 3/8-16 x 2.5" socket screws (F) and three M10 washers (K) as shown in
figure 1.1. Tighten screws using 7/32" allen wrench (J). Run cords through upright (B) using cord management
holes as shown in figure 1.2.
FK
B
A
CORD
MANAGEMENT HOLE
CORD
MANAGEMENT HOLE
fig. 1.1 fig. 1.2
B
Slide display mounting bracket (C) onto upright (B)
so that 1/4-20 nuts (G) slide into slots of upright (B)
as shown in figure 3.1 and detail 1. Slide display
mounting bracket to desired position, level, then
tighten 1/4-20 x 12 mm screws (H) using 4 mm allen
wrench (I).
Loosely attach six 1/4-20 x 12 mm screws (H) and
1/4-20 nuts (G) to display mounting bracket (C).
2
H
C
G
3
C
B
SLOT
fig. 3.1
H
DETAIL 1
G
B

5 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
H
C
Insert two 1/4-20 x 12 mm screws (H) into display mounting bracket (C), leaving 1/8" of exposed thread as shown
in figure 5.1 and detail 2.
4
E
B
Snap top cover (E) onto upright (B).
5
fig. 5.1
DETAIL 2
1/8"

6 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display. Place
display face side down. If display has knobs on the back, remove them to allow the adapter plate to be attached.
Place adapter plate (D) on back of display, align to holes, and center on back of display as shown below. Attach the
adapter plate to the back of the display using the appropriate combination of screws, multi-washers, and spacers
as shown in figure 6.1 or 6.2.
NOTE: Top and bottom mounting holes on display must be used for attaching adapter plate.
NOTE: Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
NOTE: For flat back displays proceed to step 6-1. For bump-out or recessed back display skip to step 6-2.
NOTE: "X" dimensions should be equal.
X
X
6
NOTES:
• The number of fasteners used will vary, depending
upon the type of display.
• Multi-washers and spacers may not be used,
depending upon the type of display.
• Use the corresponding hole in the multi-washer that
matches your screw size as shown.
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
MULTI-WASHER
Installing Adapter Plate
• Tighten screws so adapter plate is firmly attached. Do not tighten with excessive force. Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and adapter plate is still not
tightly secured, damage may occur to display or product may fail.
WARNING
D

7 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
Attaching Display using VESA 100, 200 or VESA 300 Mounting Pattern
• If screws don't get three complete turns in the display inserts or if screws bottom out and adapter plate is still not
tightly secured, damage may occur to display or product may fail.
WARNING
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
Select the screws from the baffled fastener pack that best fit your display. Begin with the shortest length screw,
hand thread through multi-washer and adapter plate (D)into display as shown below. Screw must make at least
three full turns into the mounting hole and fit snug into place. Do not overtighten. If screw cannot make three full
turns into the display, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting
holes and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Select the screws from the baffled fastener pack that best fit your display. Begin with longer length screw, hand
thread through multi-washer, adapter plate (D) and spacer in that order into display as shown below. Screw must
make at least three full turns into the mounting hole and fit snug into place. Do not overtighten. If screw cannot
make three full turns into the display, select a longer length screw from the baffled fastener pack. Repeat for
remaining mounting holes and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
6-1
6-2
D
D
DISPLAY
DISPLAY
fig. 6.1
MULTI-WASHER
SCREW
MULTI-WASHER
SCREW
fig. 6.2
SPACER

8 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
Insert two 1/4-20 x 12 mm screws (H) into holes indicated below for desired display orientation. Tighten all screws
using 4 mm allen wrench (I).
8
2° Backward Tilt 5° Forward Tilt
No Tilt
H
HH
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Attach adapter plate (D) to display mounting
bracket (C).
D
C
7
Service and Maintenance
This product has no user serviceable parts.
9

9 of 9 ISSUED: 08-05-11 SHEET #: 009-9054-5 05-07-2015
© 2011 Peerless Industries, Inc.
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
This warranty gives specific legal rights, and you may also have other rights which vary from state to state.
LIMITED FIVE-YEAR WARRANTY
www.peerlessmounts.com