peerless-AV SGLS01 Guide

Max Load Capacity:
150 lb (68 kg) display
50 lb (23 kg) per shelf
2300 White Oak Circle • Aurora, IL 60502 • [phone] • Fax: [phone] • www.peerless-av.com
ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
Installation and Assembly:
32" - 65" Flat Panel Display Stand
Model: SGLS01, SGLB01

2 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-708-865-2112.
• This product should only be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• Never exceed the Maximum Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The cart is not affixed or secured to the floor, and may therefore tip over and/or fall if display and/or stand is shaken
or hit. Always monitor children and do not let children play alone around stand as they could get hurt by a falling
display. Not recommended for use in areas with heavy traffic.
WARNING
Table of Contents
Parts List............................................................................................................................................................................ 3, 4
Assembling Floor Stand .........................................................................................................................................................4
Attaching Display Using Universal Plate with Adapter Brackets.............................................................................................7
Attaching Display with VESA 100 Mounting Pattern.............................................................................................................11
Tools Needed for Assembly
•level
• phillips screwdriver
NOTE: Read entire instruction sheet before you start installation and assembly.

3 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
I
AB
C
DG
F
H
J
R
S
UTP
NM
L
K
NOTE: Some parts may appear slightly different than illustrated.
SGLB01 SGLS01
Description Qty. Part # Part #
Ascreen mount bracket 1 201-1156 201-4156
Bhook plate 1 201-1157 201-4157
Cshelf support 1 201-1158 201-4158
Dshelf clamp bracket 1 201-1159 201-4159
Ebase 1 201-1981 201-4981
Funiversal plate 1 201-1109 201-4109
Gadapter bracket 2 202-1656 202-4656
Hupright 1 580-1180 580-4180
Iglass shelf 1 590-0208 590-0208
Jtop cover 1 590-1210 590-4210
Kbutton bumper 9 590-1209 590-1209
L1/4-20 x 12 mm decorative screw 12 520-2325 520-1325
M1/4-20 x 20 mm decorative screw 2 520-2326 520-1326
N1/4-20 nut 10 530-1050 530-2031
P3/8-16 x 2.5" socket screw 3 520-9550 520-9550
Q7/32" allen wrench 1 560-9715 560-9715
R4 mm allen wrench 1 560-9646 560-9646
Sadhesive felt 1 570-0043 570-0043
TM10 x 15 mm socket screw 4 520-9262 520-9262
U6 mm allen wrench 1 560-9716 560-9716
Parts List
Before you begin, make sure all parts shown are included with your product.
E
Q

4 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
1Cut adhesive felt (S) into four pieces as shown in figure 1.1 below and affix to bottom of base (E).
Attach upright (H) to base (E) using three 3/8-16 x 2.5" socket screws (P). Tighten screws using 7/32" allen
wrench (Q).
Run cords through upright (H) using cord management holes as shown in figure 1.2.
1-1
PE
H
S
1-2 CORD
MANAGEMENT HOLE
CORD
MANAGEMENT HOLE
fig. 1.1 fig. 1.2
H
Adapter Bracket Fasteners
M5 x 12 mm (4)
(520-1027)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M6 x 25 mm (4)
(520-1208)
.75" spacer (4)
(540-1059)
Multi-washer (4)
(580-1398)
M8 x 25 mm (4)
(520-1031)
M8 x 12 mm (4)
(520-9571)

5 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
Loosely attach four 1/4-20 x 12 mm screws
(L) and 1/4-20 nuts (N) to shelf support (C).
Insert three button bumpers (K) into bottom of
shelf clamp bracket (D).
Attach shelf clamp bracket (D) to shelf support (C)
using two 1/4-20 x 20 mm screws (M) and two
1/4-20 nuts (N).
Insert six button bumpers (K) into shelf support
(C).
Place glass shelf (I) on shelf support.
2
L
C
N
Slide shelf support (C) onto upright (H) so that
1/4-20 nuts (N) slide into slots of upright (H) as
shown in figure 3 and detail 1. Slide shelf support
to desired position, level, then tighten 1/4-20 x 12
mm screws (L) using 4 mm allen wrench (R).
NOTE: Max of two shelves can be used
Max height of top shelf is 34" from base.
Max height of second shelf is 28" from base.
C
H
SLOT
fig. 3
DETAIL 1
3
4 5
5-1
L
3-1
N
H
4-1
I
K
C
K
N
DM
C

6 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
1/8"
L
A
Slide display mount bracket (A) onto upright (H)
so that 1/4-20 nuts (N) slide into slots of upright
(H) as shown in figure 7 and detail 2. Slide display
mount bracket to desired position, level, then
tighten 1/4-20 x 12 mm screws (L) using 4 mm
allen wrench (R).
Insert two 1/4-20 x 12 mm screws (L) into display
mount bracket (A), leaving 1/8" of exposed thread
as shown in figure 9 and detail 3.
Loosely attach four 1/4-20 x 12 mm screws (L)
and 1/4-20 nuts (N) to display mount bracket (A).
6
LA
N
7
A
H
SLOT
fig. 7
L
8
J
H
Snap top cover (J) onto upright (H). 9
fig. 9
DETAIL 3
DETAIL 2
N
H

7 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired display orientation. Tighten all screws
using 4 mm allen wrench (R).
Attach universal plate (F) to hook plate (B) using
four M10 x 15 mm socket screws (T). Tighten
screws using 6 mm allen wrench (U).
10
Attaching Display Using Universal Plate with Adapter Brackets
For attaching displays with VESA 100 hole pattern, skip to page 11.
11 Attach hook plate (B) to display mount bracket (A).
12
L
LL
2° Backward Tilt 5° Forward TiltNo Tilt
F
B
T
B
A

8 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
Note: "X" dimensions should be equal.
Installing Adapter Brackets
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display.
Place display face side down. If display has knobs on the back, remove them to allow the adapter brackets to be
attached. Place adapter brackets (G) on back of display, align to holes, and center on back of display as shown
below. Attach the adapter brackets to the back of the display using the appropriate combination of screws, multi-
washers and spacers as shown in figure 13.1 and 13.2.
NOTE: Top and bottom holes of display must always be used.
Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
GCENTER BRACKETS VERTICALLY
ON BACK OF DISPLAY
X
X
Notes:
• The number of fasteners used will vary,
depending upon the type of display.
• Multi-washers and spacers may not be
used, depending upon the type of display.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MULTI-WASHER
13
NOTE: For flat back displays proceed to step 13-1. For bump-out or recessed back display skip to step 13-2.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING

9 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as
shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into
display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place.
Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the
baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
DISPLAY
MULTI-WASHER
SCREW
ADAPTER
BRACKET (G)
fig. 13.2
SPACER
fig. 13.1
13-1
13-2
ADAPTER
BRACKET (G)
DISPLAY
MULTI-WASHER
SCREW
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.

10 of 35 ISSUED: 07-28-06 SHEET #: 202-9156-15 (2014-04-09)
Mounting and Removing Flat Panel Display
Hook adapter brackets (G) onto universal plate (F), then slowly swing display in as shown. Turn screws clockwise
at least six times to prevent display from being removed as shown in detail 4.
NOTE: Tighten using 4 mm allen wrench (R).
Display can be adjusted horizontally if desired.
NOTE: It is important to lock display down! To lock the display down, tighten screws to adapter bracket as
shown in detail 4.
To remove display from mount, loosen screws, swing display away from mount, and lift display off of mount.
14
DETAIL 4
SCREWS
• Always use an assistant or mechanical lifting equipment to safely lift and position the display.
WARNING
G
F
G