peerless-AV DS-LEDP Series User manual

12017-02-13 #:146-9011-4 (2018-03-02)
ENG
DS-LEDP
Series
*Actual configuration may vary

22017-02-13 #:146-9011-4 (2018-03-02)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG x3
Screws must get at
least three full turns
and fit snug.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/16"
(8mm)
7/16"
(11mm)
ENG - This product is designed to be installed on unistruts. Before installing make sure the supporting surface
will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not
overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be
careful not to pinch fingers when operating the mount. For support please call customer care at 1-800-865-2112.
WARNING
4mm

32017-02-13 #:146-9011-4 (2018-03-02)
Parts (Before beginning, make sure you have all parts shown below).
ENG
J
scissor
mechanism kit
Parts List
Part #Description Qty
A corner bracket kit KIT-LED001-2
corner bracket asy 1
wood screw 1
B extrusion connector kit KIT-LED004A-2
extrusion connector asy 1
C corner adaptor kit KIT-LEDADP-XXXA-2
top corner bracket asy 2
bottom corner bracket asy 2
screw 4
washer (optional) 4
D side adaptor kit KIT-LEDADP-XXXB-2
outer bracket 1
screw 1
washer (optional) 1
E top center adaptor kit KIT-LEDADP-XXXC-2
top center bracket asy 1
screw 2
washer (optional) 2
F bottom center adaptor kit KIT-LEDADP-XXXD-2
bottom center bracket 1
screw 2
washer 2
G horizontal spacer kit KIT-LEDSPR-XXX
outside spacer 2
inside spacer 2
H cross tube support bracket kit KIT-LED006-2
hook bracket asy 2
self drilling screw 2
I tube kit KIT-LEDTUBE-XXX
tube 2
J scissor mechanism kit KIT-LED007
scissor mechanism 1
1/4"-20 x 2.5" carriage bolt 4
fender washer 4
1/4"-20 locknut 4
1/2"-13 x 5.5" screw 1
1/2"-13 hex nut 1
K extrusion kit KIT-LEDEXTXXX

42017-02-13 #:146-9011-4 (2018-03-02)
H
cross tube
support bracket kit
C
corner adaptor
kit
A
corner bracket
kit
B
extrusion
connector kit
E
top center
adaptor kit
G
horizontal
spacer kit
D
side adaptor kit F bottom center
adaptor kit
K
extrusion kit
I
tube kit

52017-02-13 #:146-9011-4 (2018-03-02)
1
Refer to layout drawing included for your
specific model.
ENG

62017-02-13 #:146-9011-4 (2018-03-02)
2-1
ENG Channel nut must start
in vertical position. ENG Tighten screw to lock channel nut.
Insert corner brackets and support brackets into
extrusion and tighten screw to lock channel nut in
place.
ENG
Left column
ENG
4mm A (2)
H (2)
K

72017-02-13 #:146-9011-4 (2018-03-02)
ENG Channel nut must start
in vertical position. ENG Tighten screw to lock channel nut.
Middle columns
ENG
H (2)
A (4)
K
2-2
Insert corner brackets and support brackets into
extrusion and tighten screw to lock channel nut in
place.
ENG
4mm

82017-02-13 #:146-9011-4 (2018-03-02)
ENG Channel nut must start
in vertical position. ENG Tighten screw to lock channel nut.
Right column
ENG
A (2)
K
H (2)
2-3
Insert corner brackets and support brackets into
extrusion and tighten screw to lock channel nut in
place.
ENG
4mm

92017-02-13 #:146-9011-4 (2018-03-02)
3
Optional: Use extrusion connector if provided.
ENG
Tighten connecting hardware.
K
K
B
4mm

10 2017-02-13 #:146-9011-4 (2018-03-02)
4-1
Tighten corner bracket hardware.
ENG
4mm
Secure right vertical column onto both horizontal
columns.
ENG
K