Pelican 2490 User manual

PELICANTM
PELICANTM 2490 LED
© PELICAN PRODUCTS 2010
5-0636 REV A 2493-311-000 AP/10
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
BATTERY INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3.
Remove used batteries and replace with fresh
batteries as shown on the outside of the
engraved body.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ON/OFF
Swing the switch lever to the right (light facing away from
you) until light activates. To turn light off, swing the switch
lever to the left (light facing away from you) until light goes off.
CAUTION:
If light is not to be used for some time, remove
batteries to prevent possible leakage and corrosion.
PRODUCT SPECIFICATIONS
Lamp Type: RecoilTM LED
Battery Type: 1.5V Alkaline AA-cell (4)
To use Traffic Wand:
1. Remove lens housing by turning counter clockwise.
2. Place colored disc (if desired) into wand, taking care
to keep the disc flat and not bend or crease it.
3. Place wand onto light body and turn
clockwise to tighten.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-RING
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which are present to
absorb hydrogen gas that could possibly be emitted by defective,
leaking, reversed polarity or heavily discharged batteries. If the
pellets become wet, let them air dry. Pelican Products assumes no
liability for any brand batteries which are defective or cause injury to
anyone when used in any Pelican flashlight.
Battery Replacement
Battery replacement may only be performed in a non-hazardous
area. Do not mix battery brands or use Nicad or Zinc Carbon
Batteries. Do not mix old and new batteries. Replace all batteries
at the same time.
DO NOT MODIFY THIS PRODUCT!
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICAN TM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel: [phone] • FAX [phone]
PELI TM PRODUCTS, S.L.U.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify you
of any handling and return postage charges. If your
local retailer does not stock the above accessory parts,
you may order them directly from Pelican Products.
Send check or money order in U.S. dollars, or order by
phone using MasterCard or VISA (ask for Customer
Service). SORRY, NO C.O.D.’s. Subject to sales tax.
Allow 2-3 weeks delivery time. Pelican Products pays
postage and handling charges. POSTAGE PAID FOR
U.S. ZIP CODES ONLY.
PELICANTM 2490 LED
INSTALACIÓN DE LAS PILAS
1. Retire el alojamiento de la lente girándolo en el
sentido contrario al de las agujas del reloj.
2. Retire la lámpara y el módulo de contacto.
3. Saque las pilas gastadas y sustitúyalas por pilas
nuevas tal y como se indica en la parte exterior del
cuerpo de la linterna.
4. Vuelva a colocar el módulo de contacto y la lámpara.
5. Vuelva a colocar el alojamiento de la lente
directamente sobre la rosca y gírelo en el sentido
de las agujas del reloj presionando ligeramente el
alojamiento de la lente.
ON/OFF
Empuje el interruptor a la derecha (desviando la luz) hasta
que se active la linterna. Para apagar la linterna, empuje el
interruptor a la izquierda (desviando la luz) hasta que la
luz se apague.
ADVERTENCIA:
Si la linterna no va a ser utilizada durante un tiempo, retire
las pilas para evitar posibles fugas y la corrosión.
ESPECIFICACIONES DEL PRODUCTO
Tipo de lámpara: RecoilTM LED
Tipo de pilas: Pilas alcalinas de 1,5V (4)
Para utilizar el cono tráfico:
1. Retirar el alojamiento de la lente girándolo en el
sentido contrario a las agujas del reloj.
2. Colocar si de desea el disco de color en la varita,
procurando que quede plano y sin doblarlo ni arrugarlo.
3. Colocar el cono tráfico en el cuerpo de la linterna y
apretar girando en el sentido de las agujas del reloj.
PIEZAS DE REPUESTO
CAT # DESCRIPCIÓN
2401 ANILLO DE SELLADO

PELICANTM
PELICANTM 2490 LED
© PELICAN PRODUCTS 2010
5-0636 REV A 2493-311-000 AP/10
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
BATTERY INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3.
Remove used batteries and replace with fresh
batteries as shown on the outside of the
engraved body.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ON/OFF
Swing the switch lever to the right (light facing away from
you) until light activates. To turn light off, swing the switch
lever to the left (light facing away from you) until light goes off.
CAUTION:
If light is not to be used for some time, remove
batteries to prevent possible leakage and corrosion.
PRODUCT SPECIFICATIONS
Lamp Type: RecoilTM LED
Battery Type: 1.5V Alkaline AA-cell (4)
To use Traffic Wand:
1. Remove lens housing by turning counter clockwise.
2. Place colored disc (if desired) into wand, taking care
to keep the disc flat and not bend or crease it.
3. Place wand onto light body and turn
clockwise to tighten.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-RING
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which are present to
absorb hydrogen gas that could possibly be emitted by defective,
leaking, reversed polarity or heavily discharged batteries. If the
pellets become wet, let them air dry. Pelican Products assumes no
liability for any brand batteries which are defective or cause injury to
anyone when used in any Pelican flashlight.
Battery Replacement
Battery replacement may only be performed in a non-hazardous
area. Do not mix battery brands or use Nicad or Zinc Carbon
Batteries. Do not mix old and new batteries. Replace all batteries
at the same time.
DO NOT MODIFY THIS PRODUCT!
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICAN TM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel: [phone] • FAX [phone]
PELI TM PRODUCTS, S.L.U.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify you
of any handling and return postage charges. If your
local retailer does not stock the above accessory parts,
you may order them directly from Pelican Products.
Send check or money order in U.S. dollars, or order by
phone using MasterCard or VISA (ask for Customer
Service). SORRY, NO C.O.D.’s. Subject to sales tax.
Allow 2-3 weeks delivery time. Pelican Products pays
postage and handling charges. POSTAGE PAID FOR
U.S. ZIP CODES ONLY.
PELICANTM 2490 LED
INSTALACIÓN DE LAS PILAS
1. Retire el alojamiento de la lente girándolo en el
sentido contrario al de las agujas del reloj.
2. Retire la lámpara y el módulo de contacto.
3. Saque las pilas gastadas y sustitúyalas por pilas
nuevas tal y como se indica en la parte exterior del
cuerpo de la linterna.
4. Vuelva a colocar el módulo de contacto y la lámpara.
5. Vuelva a colocar el alojamiento de la lente
directamente sobre la rosca y gírelo en el sentido
de las agujas del reloj presionando ligeramente el
alojamiento de la lente.
ON/OFF
Empuje el interruptor a la derecha (desviando la luz) hasta
que se active la linterna. Para apagar la linterna, empuje el
interruptor a la izquierda (desviando la luz) hasta que la
luz se apague.
ADVERTENCIA:
Si la linterna no va a ser utilizada durante un tiempo, retire
las pilas para evitar posibles fugas y la corrosión.
ESPECIFICACIONES DEL PRODUCTO
Tipo de lámpara: RecoilTM LED
Tipo de pilas: Pilas alcalinas de 1,5V (4)
Para utilizar el cono tráfico:
1. Retirar el alojamiento de la lente girándolo en el
sentido contrario a las agujas del reloj.
2. Colocar si de desea el disco de color en la varita,
procurando que quede plano y sin doblarlo ni arrugarlo.
3. Colocar el cono tráfico en el cuerpo de la linterna y
apretar girando en el sentido de las agujas del reloj.
PIEZAS DE REPUESTO
CAT # DESCRIPCIÓN
2401 ANILLO DE SELLADO

PELICANTM
PELICANTM 2490 LED
© PELICAN PRODUCTS 2010
5-0636 REV A 2493-311-000 AP/10
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
BATTERY INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3.
Remove used batteries and replace with fresh
batteries as shown on the outside of the
engraved body.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ON/OFF
Swing the switch lever to the right (light facing away from
you) until light activates. To turn light off, swing the switch
lever to the left (light facing away from you) until light goes off.
CAUTION:
If light is not to be used for some time, remove
batteries to prevent possible leakage and corrosion.
PRODUCT SPECIFICATIONS
Lamp Type: RecoilTM LED
Battery Type: 1.5V Alkaline AA-cell (4)
To use Traffic Wand:
1. Remove lens housing by turning counter clockwise.
2. Place colored disc (if desired) into wand, taking care
to keep the disc flat and not bend or crease it.
3. Place wand onto light body and turn
clockwise to tighten.
REPLACEMENT PARTS
CAT # DESCRIPTION
2401 O-RING
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which are present to
absorb hydrogen gas that could possibly be emitted by defective,
leaking, reversed polarity or heavily discharged batteries. If the
pellets become wet, let them air dry. Pelican Products assumes no
liability for any brand batteries which are defective or cause injury to
anyone when used in any Pelican flashlight.
Battery Replacement
Battery replacement may only be performed in a non-hazardous
area. Do not mix battery brands or use Nicad or Zinc Carbon
Batteries. Do not mix old and new batteries. Replace all batteries
at the same time.
DO NOT MODIFY THIS PRODUCT!
23215 Early Ave. • Torrance, CA 90505 USA
Tel [phone] • FAX [phone] • www.pelican.com
PELICAN TM CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel: [phone] • FAX [phone]
PELI TM PRODUCTS, S.L.U.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel [phone] • FAX [phone] • www.peli.com
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify you
of any handling and return postage charges. If your
local retailer does not stock the above accessory parts,
you may order them directly from Pelican Products.
Send check or money order in U.S. dollars, or order by
phone using MasterCard or VISA (ask for Customer
Service). SORRY, NO C.O.D.’s. Subject to sales tax.
Allow 2-3 weeks delivery time. Pelican Products pays
postage and handling charges. POSTAGE PAID FOR
U.S. ZIP CODES ONLY.
PELICANTM 2490 LED
INSTALACIÓN DE LAS PILAS
1. Retire el alojamiento de la lente girándolo en el
sentido contrario al de las agujas del reloj.
2. Retire la lámpara y el módulo de contacto.
3. Saque las pilas gastadas y sustitúyalas por pilas
nuevas tal y como se indica en la parte exterior del
cuerpo de la linterna.
4. Vuelva a colocar el módulo de contacto y la lámpara.
5. Vuelva a colocar el alojamiento de la lente
directamente sobre la rosca y gírelo en el sentido
de las agujas del reloj presionando ligeramente el
alojamiento de la lente.
ON/OFF
Empuje el interruptor a la derecha (desviando la luz) hasta
que se active la linterna. Para apagar la linterna, empuje el
interruptor a la izquierda (desviando la luz) hasta que la
luz se apague.
ADVERTENCIA:
Si la linterna no va a ser utilizada durante un tiempo, retire
las pilas para evitar posibles fugas y la corrosión.
ESPECIFICACIONES DEL PRODUCTO
Tipo de lámpara: RecoilTM LED
Tipo de pilas: Pilas alcalinas de 1,5V (4)
Para utilizar el cono tráfico:
1. Retirar el alojamiento de la lente girándolo en el
sentido contrario a las agujas del reloj.
2. Colocar si de desea el disco de color en la varita,
procurando que quede plano y sin doblarlo ni arrugarlo.
3. Colocar el cono tráfico en el cuerpo de la linterna y
apretar girando en el sentido de las agujas del reloj.
PIEZAS DE REPUESTO
CAT # DESCRIPCIÓN
2401 ANILLO DE SELLADO