Pennsylvania Scale Company SS6600 MAX-LT User manual

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 1of 8
665 North Reservoir Street
Lancaster PA 17602
P: 800.233.0473 717.295.6935
[email protected]
Manual Manual SS6600 MAX-LTTM2023REV1

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 2of 8
Unpacking and Startup
Scale Base
•The base to indicator interface cable is located underneath the
base on the same side as the junction box with the Pennsylvania
Scale Logo.
•The cable is attached to two clips affixed underneath the base to
protect it during shipment. Unhook the cable from the clips and
uncoil to attach to the indicator.
Level the Base
•The leveling feet must be turned out at least two turns for
proper operation of the base. At this point in the set up
procedure, the base may be placed onthe floor. Access to the
junction box should not be blocked in the event that
adjustments to the base are required.
•After the base is on the floor, adjust the leveling feet so
that all four feet are in firm contact with the floor.
•NOTE: For the 6600 base to work properly, the base must be
supported on the leveling feet. If the leveling feet are not
extended far enough and the base is wholly or partially sitting
on the steel under frame, the base will not weigh correctly.

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 3of 8
SPECIFICATIONS
•CONSTRUCTION: 304 Stainless Steel Heavy Duty Bar Steel Frame and Deck Plate.
•IP69K Washdown Protection
•Accuracy: 5,000 divisions
•OPTIONS:
oRAMPS
oBUMPER GUARDS
oBASE ANCHORS
oFORKLIFT SKIDS
oSPECIAL SIZES and CONFIGURATIONS
•Made in the USA

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 4of 8
Using the Lift Up Deck Plate:
Remove the Center Plate
Lift up the Deck Plate, Gas Struts will Assist and Hold in the Open Position
To Close, Push Down Deck Plate and Replace Center Plate

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 5of 8
NOTE: Please refer to the
indicator technical manual for calibration instructions
Pennsylvania Scale Base to Indicator Connections:
The SS6600 MAX-LT comes with a pig tail end so that the load cell cable may be inserted
through the watertight cable clamp used on the Pennsylvania Scale wash down indicators.
Pennsylvania Scale Load Cell Cable Wiring:

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 6of 8
Base Summing Card Connections:
To access the junction box, remove the screws securing the top cover.
IMPORTANT NOTE:All Screws must be in and tightened in order to maintain washdown
protection!
Excitation+
RED
Sense+
ORANGE
Signal+
GREEN
Shield/Ground
CLEAR
Signal-
WHITE
Sense-
BLUE
Excitation
BLACK
Excitation+
RED
Signal+
GREEN
Shield/Ground
CLEAR
Signal-
WHITE
Excitation
BLACK

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 7of 8
Load Cell Ratings
The SS6600 MAX-LT is available in capacities of 1,000 to 5,000 LB. The typical load cell
sensitivity is 2 mv/v except 1,000 LB capacity, which is 1 mv/v.
Calibration Instructions
Please refer to the calibration instructions for the digital indicator that will be used with the
base.
Basic Trouble Shooting
•ARE THE LEVELING FEET TURNED OUT AT LEAST 2 FULL TURNS?
•The load cells in the base have tested and corner compensated at the factory and should
not require adjustment for installation. If the base is displaying inaccurate weight
readings or corner weight errors, check the following before making potentiometer
adjustments:
•Check the cable; is it wedged between the leveling feet and floor or in between the load
cell and base structure?
•Is the base fully and firmly supported by the leveling feet? Does the base rock or tip if
weight is placed on one corner?
•Are there any obstructions between the load cells and the leveling feet?
•Is the base to indicator load cell cable attached?
•Are the connections at the indicator correct?

SS6600 MAX-LT Technical Manual
For Tech Support Manuals and How To Videos go to: pascale.com/resource-library/ or email us at: [e-mail]
Page 8of 8
Replacement Parts List
Part No:
Description
Notes
56699-1
6600 4-cell Summing/Junction Board in SS
J-Box
Universal fit all 4 load cell systems;
excitation trim
49737-7
SS6600, SS6900, ½-20 UNF, SS, 2" base
diameter, 2-1/2" high
SS Floor Scales 1, 2, 5, and 10K
48817-30
30’ Load Cell Cable assy. 6600
Standard cable – 30’ length
48817-40
40’ Load Cell Cable assy. 6600
Standard cable – 40’ length
48817-50
50’ Load Cell Cable assy. 6600
Standard cable – 50’ length
Stainless Steel Washdown Load Cells
Part No:
Description
Notes
57651-1
HERMETIC
SS Hermetically sealed cell, 1000 lbs. (small
envelope)
65083S1K-5100
57651-2
HERMETIC
SS Hermetically sealed cell, 2500 lbs. (small
envelope)
65083S2.5K-5100
57651-4
HERMETIC
20,000 lbs. / 20' cable
65083S4K-5100
Lift Top Deck Plate Parts
Part No:
Description
MAXLT-59277
SPACER BAR SS6600
MAXLT-73497-2
CLEVIS, GAS SPRING
MAXLT-73067-3
QUICK RELEASE CLEVIS PIN
MAXLT-73066-2
GAS SPRING SS316
MAXLT-35557
LASH 708/910 FL. SC