Pepperl+Fuchs WCS-EIG410 User manual

WCS-EIG410
WCS Interface Module
EtherNet/IP
Manual

With regard to the supply of products, the current issue of the following document is applicable: The
General Terms of Delivery for Products and Services of the Electrical ndustry, published by the Central
Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elektroindustrie (ZVE ) e.V.)
in its most recent version as well as the supplementary clause: "Expanded reservation of proprietor-
ship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [e-mail]
North American eadquarters
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [e-mail]
Asia eadquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [e-mail]
https://www.pepperl-fuchs.com

3
WCS-E G410
Contents
2020-03
1 Introduction................................................................................................................ 4
1.1 Content of this Document............................................................................. 4
1.2 Target Group, Personnel ............................................................................... 4
1.3 Symbols Used ................................................................................................ 4
2 Product description................................................................................................... 6
2.1 Use and Application ...................................................................................... 6
2.2 Dimensions..................................................................................................... 6
2.3 Design of the Device...................................................................................... 7
3 Installation................................................................................................................ 11
3.1 Mounting....................................................................................................... 11
3.2 Electrical Connection .................................................................................. 12
3.3 Dismounting................................................................................................. 14
4 Commissioning........................................................................................................ 15
4.1 Introduction.................................................................................................. 15
4.2 Connecting the WCS Read ead................................................................ 15
4.3 Connection to the Network ......................................................................... 17
4.4 Setting the IP Address and Subnet Screen............................................... 18
4.5 Network Settings ......................................................................................... 19
4.6 Data Format for Modules ............................................................................ 21
5 Communication with WCS read heads .................................................................. 23
5.1 Data Protocols ............................................................................................. 23
5.2 Option-E—Extended, Type WCS3B-LS2*E*, RS-485................................. 26
6 Appendix .................................................................................................................. 29
6.1 Software Tool for RSLogix 5000, V15, and V17 ......................................... 29
6.2 Cable Routing in the RS-485 Bus ............................................................... 29
6.3 Data Cable .................................................................................................... 32

2020-03
4
WCS-E G410
ntroduction
1 Introduction
1.1 Content of this Document
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
n addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•nstruction manual
•Other documents
1.2 Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product. The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the nternet at
www.pepperl-fuchs.com.

WCS-E G410
ntroduction
2020-03
5
1.3 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Warning Messages
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
Informative Symbols
Action
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

2020-03
6
WCS-E G410
Product Description
2 Product Description
2.1 Use and Application
The WCS-EIG410 interface module acts as an interface between the WCS read head and the
EtherNet/ P controller. Data is transferred between the WCS read head and the interface mod-
ule via an RS-485 interface. The data from the interface module to the controller is transferred
via the EtherNet/ P protocol.
You can connect a maximum of four LS221 (and/or LS121) WCS read heads to one WCS-
E G410 interface module. f you connect several WCS read heads, they must have different
addresses. The number of connected WCS read heads is configured in the hardware project
planning.
The interface module supports the operation of read heads with the Extended option (WCS3B-
LS*E*), with distances of up to 629 meters.
2.2 Dimensions
The interface module housing has the following dimensions.
Figure 2.1 Dimensions
115
100 23

WCS-E G410
Product Description
2020-03
7
2.3 Design of the Device
Device Components
Figure 2.2 nterface module overview
1RS-485 bus termination slide switch
2X1: RS-485 interface
3Mounting bracket
4X2: Connection for power supply
5X3: EtherNet/ P communication interface
6Front panel with rotary coding switch and LED status indicator
4
3
5
6
2
1

2020-03
8
WCS-E G410
Product Description
Front Panel
Figure 2.3 Front panel overview
WCS read head: LED status indicator and rotary coding switch
Power:
The "Power" LED lights up green: power supply is present.
State:
The "State" LED is green: Data is being exchanged with the WCS read heads. The four "Error
No/Select D" LEDs are used to display the number of the currently polled WCS read head.
The "State" LED lights up red: The interface module has detected an error or a warning. The
interface module displays the binary-coded error and/or warning number via the "Error
No/Select D" LEDs.
Error No/Select ID Read head
address
8 4 2 1
00010
00101
01002
10003
Table 2.1 Display via the four "ErrorNo/Select D" LEDs when the "State" LED lights up green
Error (No. 1...5): Switch the interface module off and back on. f the error occurs
again, the module must be replaced.
Warning (No. 6...15): The warning provides information. The interface module displays
the warning for one minute and then resets automatically.
Power
1
2
4
8
State
WCS-EIG410 Modul
Net Status
Power Link/Act. P1 Link/Act. P2
EtherNet/IP
Mod Status
S4 S5
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9

WCS-E G410
Product Description
2020-03
9
Rotary Coding Switches S4 and S5
Rotary coding switches S4 and S5 are used to determine the number of read heads and the
protocol used (WCS or WCS Extended); see chapter 4.2.
LED ErrorNo/Select ID Error number Error description
LED8 LED4 LED2 LED1
00000
Reserved
00011
Hardware error
00102
EEPROM error
00113
nternal memory error
01004
Fieldbus hardware error or incorrect
fieldbus D
01015
Script error
01106
Reserved
01117
WCS read head communication, RS
send buffer overflow
10008
WCS read head communication, RS
receive buffer overflow
10019
WCS read head communication, RS
timeout
1 0 1 0 10
General fieldbus error
1 0 1 1 11
Parity error or frame check error
1 1 0 0 12
Reserved
1 1 0 1 13
Fieldbus configuration error
1 1 1 0 14
Fieldbus data buffer overflow
1 1 1 1 15
Reserved
Table 2.2 Significance of the error codes (display via the four "Error No/Select D" LEDs when the
"State" LED lights up red and thus indicates an error or a warning)

2020-03
10
WCS-E G410
Product Description
EtherNet/IP: LED status indicator
Net Status:
Mod Status:
Power:
The "Power" LED lights up green: This LED is directly connected to the supply voltage of the
serial interface (RS232/422/485).
Link/Activity P1:
The "Link/Activity Port 1" LED is directly activated by the Ethernet controller and lights up green
when the interface module at port 1 is on a working network. When there is data traffic on the
network, the LED flashes green at the same speed as the sent/received data.
Link/Activity P2:
The "Link/Activity Port 2" LED is directly activated by the Ethernet controller and lights up green
when the interface module at port 2 is on a working network. When there is data traffic on the
network, the LED flashes green at the same speed as the sent/received data.
"Net Status" LED Interface state
Flashes green/red Self-test
Lights up green Connection present, data exchange is active
Flashes green Waiting for a connection to be established
Flashes red Connection has timed out
Lights up red P address assigned twice
Table 2.3 "Net Status" LED indicator
"Mod Status" LED Interface state
Flashes green/red Self-test
Lights up green Data exchange active
Flashes green Standby/module waiting for connection
Flashes red Module error
Lights up red Serious module error
Table 2.4 "Mod Status" LED indicator