Pepperl+Fuchs Bebco EPS 5500 Series User manual

5500 Purge System
User Manual
Bebco EPS® 5500 Series Type Z and
Ex pzc Purge and Pressurization System

With regard to the supply of products, the current issue of the following document is applicable:
The General Terms of Delivery for Products and Services of the Electrical Industry, published by the
Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie
(ZVEI) e.V.) in its most recent version as well as the supplementary clause: “Expanded reservation of
proprietorship”.
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [e-mail]
North American Headquarters
Pepperl+Fuchs Inc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [email protected].com
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [email protected]
https://www.pepperl-fuchs.com
ii
•

Table of contents
1. Introduction.............................................................................................6
1.1. Content of this Document ............................................................................. 6
1.2. Target Group, Personnel................................................................................7
1.3. Symbols Used...............................................................................................8
1.4. Pertinent Laws, Standards, Directives, and Further Documentation.............. 9
1.5. Declaration of Conformity..............................................................................9
2. Product Description .............................................................................10
2.1. Introduction.................................................................................................10
2.2. 5500 System Overview ...............................................................................10
2.3. Control Unit................................................................................................. 10
2.3.1 Technical Data: Control Unit ...................................................................11
2.3.2 Electrical Connections............................................................................17
2.3.3 Dimensions ............................................................................................ 18
2.3.4 Hardware Kit .......................................................................................... 21
2.3.5 Torque Requirements: Control Unit.........................................................21
2.3.6 Internal-Mounting the Control Unit.......................................................... 22
2.3.7 External-Mounting the Control Unit ........................................................23
2.4. EPV-5500 Vents .......................................................................................... 24
2.4.1 Technical Data: EPV-5500 Vents ............................................................24
2.4.2 Flow Rate Curves................................................................................... 26
2.4.3 Dimensions: EPV-5500 Vents.................................................................30
2.4.4 Torque Requirements: EPV-5500 Vents.................................................. 30
2.5. Manifold Valves........................................................................................... 30
2.5.1 Technical Data: 5500 Manifolds.............................................................. 32
2.5.2 Dimensions: 5500 Manifolds ..................................................................34
2.5.3 Torque Requirements: Manifolds............................................................36
3. Installation and Operation...................................................................37
3.1. Installation...................................................................................................37
3.1.1 For Gas Atmospheres ............................................................................ 37
3.1.2 For Dust Atmospheres........................................................................... 38
3.1.3 Setting up the System ............................................................................38
3.2. Operation.................................................................................................... 39
3
5500 SerieS Manual  Table of conTenTS
DOCT-B3R8 • 01/2024

4. Programming ........................................................................................40
4.1. User Interface ............................................................................................. 40
4.1.1 LED Indication........................................................................................ 40
4.1.2 Buttons................................................................................................... 41
4.1.3 Adjusting the Contrast ........................................................................... 41
4.1.4 LCD Backlight ....................................................................................... 41
4.2. Default Settings........................................................................................... 42
4.3. Menu Structure ........................................................................................... 43
4.4. Purge Programs.......................................................................................... 44
4.4.1 Program 1...............................................................................................45
4.4.2 Program 2...............................................................................................46
4.4.3 Program 3...............................................................................................47
4.4.4 Program 4...............................................................................................48
4.4.5 Program 5...............................................................................................49
4.5. Purging Timer..............................................................................................50
4.5.1 Determining Purge Time.........................................................................50
4.5.2 Pressure Settings................................................................................... 52
4.5.2.1 Minimum Enclosure Pressure “P1”...................................................... 52
4.5.2.2 Alarm Pressure “P2”...........................................................................52
4.5.2.3 Purging Pressure “P3”........................................................................ 53
4.5.2.4 Maximum Internal Pressure “P4”........................................................ 53
4.5.3 Programming K2 .................................................................................... 55
4.6. Shuto Delay Timer for K1 .......................................................................... 56
4.7. Number of PT100 Temperature Sensors Used............................................ 57
4.8. Temperature Inputs PT1 and PT2................................................................58
4.9. Bypass........................................................................................................59
4.10. Units ............................................................................................................60
4.11. Temp Enabled.............................................................................................. 60
4.12. Change Password........................................................................................ 61
4.13. User Parameter Setting Sheet ..................................................................... 62
5. ProductIdentication ..........................................................................63
5.1. Specic Conditions of Use..........................................................................63
5.2. Applied Standards and Markings................................................................63
5.3. Type Codes................................................................................................. 64
5.4. Markings (Labelling) ...................................................................................65
4
5500 SerieS Manual  Table of conTenTS
DOCT-B3R8 •01/2024

6. Product Lifetime Care ..........................................................................67
6.1. Maintenance and Repair.............................................................................67
6.2. Dismantling and Decommissioning............................................................. 67
6.3. Troubleshooting........................................................................................... 68
5
5500 SerieS Manual  Table of conTenTS
2018-12

1. Introduction
1.1. Content of this Document
This document contains information required to meet the safety and protection
requirements for systems with explosion protection in equipment Group II Zones 2 or
22, Class I or II, Division 2 when installing, commissioning, and using the 5500 control
unit and its components.This important information will help you use the 5500 purge
and pressurization system safely and correctly.
This may include information on the following:
 Product identication
 Delivery, transport, and storage
 Mounting and installation
 Maintenance and repair
 Disposal
Knowledge of the basic safety regulations and additional training and experience in
the area of explosion protection are essential for the safe handling and failure-free
operation of the 5500 series purge and pressurization system.
These operating instructions contain important data and information to ensure the
safe use of the 5500 system in hazardous areas and to meet the requirements of
Directive 2014/34/EU. This manual, particularly the safety information, must be
followed by all personnel who work on the system.
WARNING!
Failure to follow these instructions may impair the safety protection and
function of the equipment.
Note
For complete information on this product, see further documentation at
www.pepperl-fuchs.com.
Information about individual components can be provided on request.
The documentation comprises the following parts:
 This document
 Safety instruction manual
 Datasheet
6
5500 SerieS Manual  inTroducTion
DOCT-B3R8 • 01/2024

In addition, the documentation may comprise the following parts, if applicable:
 Manufacturer declaration of conformity
 EU declaration of conformity
 Control drawings
 Additional documents
1.2. Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and
dismounting of the 5500 series lies with the plant operator. Personnel working on this
system must:
 be familiar with the occupational safety and accident prevention regulations and
have been briefed regarding handling of the unit.
 have the additional knowledge of explosion protection that is requied for work on
explosion-protected components.
 be familar with the relevant rules and regulations for the installation, operation,
and maintenance of explosion-protected systems.
 have read the safety section and warnings in this manual.
The operator and/or installer must also ensure that:
 the 2-wire RTDs for temperature sensors are suitable for the area classication,
Zone 2, or Zone 22, Class I, Zone 2. Maximum length is 3m.
 the bypass switch is suitable for the area classication, Zone 2 or Zone 22, Class
I, Zone 2.
 the intrinsically safe aspects of the system are installed in accordance with
manufacturer’s control drawing number 116-B026.
 that the 5500 system is used as a purge controller and not protected by purging
and pressurization
 all electrical, mechanical, and pneumatic connections have been made in
accordance with this manual and any other applicable standards and laws.
7
 inTroducTion
DOCT-B3R8 • 01/2024
5500 SerieS Manual  inTroducTion

1.3. Symbols Used
This document contains symbols to identify warning messages and information
messages.
Warnings
You will always nd warning messages whenever hazards could result from your
actions. It is essential that you observe these warning messages to ensure your
personal safety and to prevent property damage.
Warning messages are shown in descending order according to the risk level, as
follows:
DANGER!
This symbol warns you of an immediate and present danger.
If you do not observe this warning message, there is a risk of personal injury and
even death.
WARNING!
This symbol warns you of a potential fault or hazard.
If you do not observe this warning message, there is a risk of personal injury or
severe property damage.
CAUTION!
This symbol warns you of a potential fault.
Failure to observe this warning message may result in the malfunctioning or
complete failure of the product or any systems and plants connected to it.
Information Symbols and Messages
Note
This symbol draws your attention to important information.
Action instructions
This symbol highlights an action.You are prompted to perform an action or sequence
of actions.
8
5500 SerieS Manual  inTroducTion
DOCT-B3R8 • 01/2024

1.4. Pertinent Laws, Standards, Directives, and
Further Documentation
NEC, CEC, and other national and local laws, standards, or Directives that are
applicable to the intended use and installation location must be observed. In relation
to hazardous areas, Directive 1999/92/EC must be observed.
The corresponding datasheets, EU Declaration of Conformity, EU Type Examination
Certicates, NEC/NFPA and CEC certicates, and control drawings, if applicable
(see datasheet), are an integral part of this document. You can nd this information
at www.pepperl-fuchs.com.
Due to constant revisions, documentation is always subject to change. Please refer
only to the most up-to-date version, which can be found at www.pepperl-fuchs.com.
1.5. Declaration of Conformity
All products were developed and manufactured under observance of the applicable
European standards and guidelines.
Note
A Declaration of Conformity is included with these instructions and can be
requested from the manufacturer or obtained online at www.pepperl-fuchs.com.
Additional documentation can also be provided for individual components.
The product manufacturer, the Pepperl+Fuchs Group, 68307 Mannheim, has a
certied quality assurance system that conforms to ISO 9001.
ISO9001
9
 inTroducTion
DOCT-B3R8 • 01/2024
5500 SerieS Manual  inTroducTion

2. Product Description
2.1. Introduction
Purge and pressurization is one of the most versatile ignition protection classes.
Purge and pressurization systems are based on the principle that in Zone 2/Class I
Division 2 (gas), the gas mixture in the ambient atmosphere, which may ignite under
certain circumstances, is removed from the housing by an initial purge process.

compensate for leaks in the housing and any installed equipment.This permanent
overpressure prevents any potentially explosive atmosphere in the ambient air from
entering the housing. During the purge phase, an internal pressure is achieved.
Any hot spots that may occur on individual components in the control cabinet are

ensures that no unacceptably high surface temperatures can reach the exterior.
For applications in Zone 22/Class II Division 2 (dust), the purge process is omitted
because purging would raise explosive dust into a cloud, creating a possible hazard.
Instead of pre-purging, the interior of the housing is inspected for dust and cleaned
manually if dust is present.
Purge and pressurization systems are particularly suitable for installed equipment that
is not approved for use in hazardous areas.The equipment can then be used directly
in the hazardous area.
2.2. 5500 System Overview
The 5500 series system consists of a control unit with a user interface mounted in a
316 stainless steel enclosure. The control unit works in conjunction with enclosure
protection vents (EPVs) and pneumatic solenoid valves or manual valves.
The 5500 is a purge/pressurization controller and is not protected by pressurization.
2.3. Control Unit
The 5500 control unit is a control device for Type Z and Ex pzc purge systems. The
unit is suitable for purge time and pressure monitoring in Class I or II, Division 2, Zone

and it maintains and monitors an overpressure relative to the ambient air when
purging is complete.


10
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

Control Unit Components
z5500 control unit
zCable glands / conduit openings available
zMounting bolts and sealing washers for attaching control unit to an enclosure
z
zManual
2.3.1 Technical Data: Control Unit
Item Value
Supply
Rated voltage Ur 100 ... 240 V AC, 0.05 A, 50 ... 60 Hz
20 ... 30 V DC, 0.2 A
Overvoltage category II
Power consumption 100 ... 240 V AC - 2.3 VA (without digital valve)
20 ... 30 V DC - 2.5 W (without digital valve)
Electrical Specications
Fuse Rating F2:
AC: 2 A slow blow, 5 x 20 mm
DC: 3.15 A slow blow, 5 x 20 mm
F1:
AC: 0.08 A (max) slow blow, 5 x 20 mm
DC: 0.5 A (max) slow blow, 5 x 20 mm
Fuse must be UL Recognized under JDYX2/8
11
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

Input
Input I Temperature, up to 2 RTDs per unit
Connection PT100, 2-wire-connection
Input type temperature input
Input accuracy 2.5% of measurement value + PT100 error
Input II 1 Bypass
Connection passive contact (switch)
Input type mechanical contact
Output
Output I
Connection K1, terminals: K1/N0, K1/N0
Output type enclosure power, (1) SPST
Inrush current 6 A
Contact loading 6 A at 250 V AC, 30 V DC resistive load, 6 A at 30 V DC
Output II
Connection K2, terminals: K2 (NO, C, NC)
Output type alarm, (1) SPDT
Inrush current 3 A
Contact loading 3 A at 250 V AC , 30 V DC resistive load, 3 A at 30 V DC
Output III
Connection digital valve, terminals SV
Output type (1) SPST, powered contacts from supply
5 A V AC or V DC
Inrush current 5 A
Indicators/settings
LED indication Membrane Pad
K1: Green–Contact K1 is energized
K2: Amber–Contact K2 is energized
SV/encl press.: Blue for safe pressure, Amber for valve on
Bypass: Amber when bypass is active
PT100 error: Red when fault in PT100 sensor
Safe pressure programmable
Protective gas supply instrument grade air or inert gas
Safe pressure, programmable Gas: 0.7 mbar (0.3 in wc)
Dust: 1.6 mbar (0.65 in wc)
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EU EN 61326-1:2013
12
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

RoHS
Directive 2011/65/EU EN 50581:2012
Conformity
Degree of protection EN 60529
Shock resistance EN 60068-2
Ambient conditions
Ambient temperature -20 ... 40 °C (-4 ... 104 °F) at T6
-20 ... 60 °C (-4 ... 140 °F) at T4
Relative humidity 5 ... 95 %, non-condensing
Altitude max. 2000 m
Vibration resistance 5 ... 100 Hz , 1 g, 12 m/s², all axes
Impact resistance 30 g, 11 ms, all axes
Mechanical Specications
Connection type High pressure port: 1/8” NPTF
Low pressure port: 1/8” NPTF
Cable gland Cable size
M12 diameter 3–6.5mm
RTD/Bypass: (3) M12x1.5
M20 diameter 10–12mm
K1, K2, SV:‘P_C’ (3) M20x1.5
Degree of protection Type 4X
IP66 (Device is protected against dust and strong jets of water.)
Pollution degree Device can be installed in environments up to pollution degree 2.
Material Housing: 316 stainless steel
Cable Gland: 316 stainless steel or Nickel Plated Brass
Pressure Ports: 316 stainless steel
Membrane Pad: Autotex F200XE
O-ring: EPDM
Mass approx. 2.7 kg (6 lb)
Dimensions 165 x 124 x 90 mm (6.5 x 4.9 x 3.5 in)
Mounting control unit
(Internal/External) Mounting holes (3x 6.4mm) Screws, nuts, and sealing washers (provided)
Data for application in connection with hazardous areas
 DEMKO 14 ATEX 1282X
13
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

Marking II 3 (3) G Ex ic ec nC [ic Gc] [pzc Gc] IIC T4 Gc

II 3 (3) G Ex ic ec nC [ic Gc] [pzc Gc] IIC T6 Gc

II 3 (3) D Ex ic tc [ic IIIC Dc] [pzc Dc] IIIB T80 °C Dc

II 3 (3) D Ex ic tc [ic IIIC Dc] [pzc Dc] IIIB T60 °C Dc

II 3 (3) D Ex ic tc [ic Dc] [pzc Dc] IIIC T80 °C Dc

II 3 (3) D Ex ic tc [ic Dc ] [pzc Dc] IIIC T60 °C Dc

Directive conformity
Directive 2014/34/EU EN IEC 60079-0:2018, EN 60079-11:2012,
EN 60079-15:2019, EN 60079-2:2014,
EN 60079-7:2015+A1:2018, EN 60079-31:2014
International approvals
UL approval
cULus UL File E184741




IECEx approval IECEx UL 14.0019X



(external version)

(external version)

(internal version)

(internal version)
14
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

Bypass and Temperature Wiring Notes
1. The minimum wire strand in a stranded wire shall have a diameter of 0.1 m or greater.
2. Wire shall be copper only, rated at a minimum of 80 °C.
3. Minimum wire insulation thickness shall be 0.25 mm for each conductor.
4. Terminal torque is 0.220.25 Nm.
5. The wire strip length is 7 mm.
6. There shall be only one wire per terminal.
Item Value
Cable gland ‘L_C’ (3) M12 x 1.5
Cable size: M12 dia
3–6.5 mm
Material 316 stainless steel or nickel-
plated brass, O-ring EPDM
Conductor cross section, solid min. 0.14 mm²
Conductor cross section, solid max. 1.5 mm²
Conductor cross section, stranded min. 0.14 mm²
Conductor cross section, standed max. 1.5 mm²
Conductor cross section, with ferrule without plastic sleeve, min. 0.25 mm²
Conductor cross section with ferrule without plastic sleeve, max. 1.5 mm²
Conductor cross section with ferrule, with plastic sleeve, min. 0.25 mm²
Conductor cross section, with ferrule, with plastic sleeve, max. 0.5 mm²
Conductor cross section, AWG/kcmil min. 28
Conductor cross section, AWG/kcmil max. 16
Control Power Connection General Wiring Notes
1. All applicable local and national wiring codes must be followed when wiring the system. See
IEC 60079-14 for more information.
2. The power supply to this device shall have a separate disconnect. If placed in the hazardous
area, it shall be rated for the area in which it is being installed. Placing the disconnect into the
purged enclosure is not a “safe” area since power needs to be applied to the control unit before
the purge cycle is complete.
3. The protective earth wire must be the same size as largest wire used to bring power into the
enclosure. Terminate using a ring lug that is properly crimped at the protective earth stud in the
bottom of the enclosure.
15
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

4. For earth stud torque and terminal torque values, see Section 2.3.5 Torque Requirements—
Control Unit.
5. All wire shall be copper only, rated at a minimum of 80 °C.
6. The minimum wire strand in a stranded wire shall have a diameter of 0.1 mm or greater.

8. There shall be only one wire per terminal.
9. It is recommended to leave a bit of extra wire loop in the housing.
Connector Component Property
Cable gland ‘P_C’ (3) M20 x 1.5
Cable size: M20 dia
Clamping range single seal: 14.5 ... 16 mm
double seal: 12 ... 14.5 mm
triple seal: 10 ... 12 mm
Material 316 stainless steel or nickel-
plated brass, O-ring EPDM
Conduit “PSH” (3) 1/2” NPTF
Material 316 stainless steel or nickel-
plated brass, O-ring EPDM
Conductor cross section, min. 0.2 mm²
Conductor cross section, max. 6 mm²
Conductor cross section, stranded min. 0.2 mm²
Conductor cross section, standed max. 4 mm²
Conductor cross section, with ferrule without plastic sleeve, min. 0.25 mm²
Conductor cross section with ferrule without plastic sleeve, max. 2.5 mm²
Conductor cross section with ferrule, with plastic sleeve, min. 0.25 mm²
Conductor cross section, with ferrule, with plastic sleeve, max. 4 mm²
Conductor cross section, AWG/kcmil min. 24
Conductor cross section, AWG/kcmil max. 10
16
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

L(+)
F1
SV1
F2
Power
L(+)
L(+)
C
K2
NC SV
K1
NO
K1
NO
N(-)
N(-)
N(-)
N(-) N(-)
NO
Bypass
T1 T2
Internal Mount
Bypass T1 T2
L(+) C
K2
NC
SV K1
NO
N(-) NO
L(+) L(+) K1
NO
N(-)
N(-)
N(-) N(-)
F1
SV
F2
Power
2.3.2 Electrical Connections
External Mount
Terminal Block
L (+) N (-) SV K2 K1
17
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

2.3.3 Dimensions
Dimensions: External Mounting
1. Low pressure port (-): The atmospheric reference.This port shall always be connected such that
the air pressure present on this port is the atmospheric pressure surrounding the enclosure being
protected by pressurization. For monitoring the enclosure pressure.
2. High pressure port (+): For monitoring the enclosure pressure.This port must always connect the
control unit to the monitored enclosure protected by pressurization.
1
Low-pressure port (atmospheric pressure)
2
High-pressure port (enclosure pressure)
18
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

For the external-mount 5500 control unit, the display can be rotated 90 degrees. No
screws are required.To rotate, remove the cover and pop out the display. Position the
display as desired and push it back into the pin on the control unit. Do not rotate more
than +/- 90 degrees. When rotating the display, be careful not to collapse the tubing
by bending in extreme angles.
19
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024

Dimensions: Internal Mounting
1
Low-pressure port (atmospheric pressure)
2
High-pressure port (enclosure pressure)
1
2
1. Low pressure port (-): The atmospheric reference.This port shall always be connected
such that the air pressure present on this port is the atmospheric pressure surrounding the
enclosure being protected by pressurization.
2. High pressure port (+): For monitoring the enclosure pressure.This port must always con-
nect the control unit to the monitored enclosure protected by pressurization.
20
5500 SerieS Manual ProducT deScriPTion
DOCT-B3R8 • 01/2024