Pepperl+Fuchs VPH-F200-T User manual

VPH-F200-T
Climate Control Housing
Manual

With regard to the supply of products, the current issue of the following document is applicable:
The General Terms of Delivery for Products and Services of the Electrical ndustry, published
by the Central Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elek-
troindustrie (ZVE ) e.V.) in its most recent version as well as the supplementary clause:
"Expanded reservation of proprietorship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [email protected]
North American Headquarters
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [email protected]
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [email protected]rl-fuchs.com
https://www.pepperl-fuchs.com

VPH-F200-T
Contents
2019-10
3
Introduction................................................................................................................ 4
. Content of this Document............................................................................. 4
.2 About This Documentation ........................................................................... 4
.3 Symbols Used ................................................................................................ 5
2 Safety Information ..................................................................................................... 6
3 Product Description .................................................................................................. 7
4 Transport and Storage .............................................................................................. 9
5 Mounting................................................................................................................... 0
6 Commissioning........................................................................................................ 25
7 Servicing................................................................................................................... 26

2019-10
4
VPH-F200-T
ntroduction
Introduction
. Content of this Document
This document contains safety-relevant information for using the device. This information is
required to use the product in the relevant phases of the product life cycle. This may include
information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
.2 About This Documentation
Note on Figures in the Documentation
The figures in this documentation are provided for basic understanding and may deviate from
the actual design.
Note
Availability of the Complete Product Documentation
Full information about the product can be found in the product documentation online at
www.pepperl-fuchs.com. This documentation can be accessed by entering the product name
(type code) or the item number of the product into the search field on the website.

VPH-F200-T
ntroduction
2019-10
5
.3 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Warning Messages
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
Informative Symbols
Action
. This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

2019-10
6
VPH-F200-T
Safety nformation
2 Safety Information
Read the information in this document carefully and observe this information when working
with the device. Failure to observe the safety information and warning messages in this docu-
mentation can lead to malfunctions of the safety devices of the machines or plants in which
they are fitted.
This can result in serious personal injury or death.
Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
The personnel must be appropriately trained and qualified in order to carry out mounting,
installation, commissioning, operation, maintenance, and dismounting of the device. The
trained and qualified personnel must have read and understood the instruction manual.
Prior to using the product make yourself familiar with it. Read the instruction manual carefully.

VPH-F200-T
Product Description
2019-10
7
3 Product Description
The "VPH-F200-T" climate control housing (hereinafter referred to as the VPH housing)
extends the range of applications for the chosen sensor modules, allowing them to be used at
an ambient temperature of up to +80 °C. The sensor fixture is designed for the Data Matrix
positioning system (PXV) with the "F200" housing design.
The VPH housing encloses the sensor module, creating a compact component for integration
at the operating location. Based on a constant difference in temperature, the internal housing
temperature is regulated in line with the ambient temperature. This means that the system will
follow temperature fluctuations after a specific delay.
Figure 3.1 Overview
1. Upper shell
2. Sensor fixture
3. Housing base
4. Mounting foot
5. Sensor (example)
6. 4 mm and 5 mm Allen wrenches (not included in the scope of delivery)
7. Mounting screws for the upper shell (11 screws)
8. Sealing rings for the upper shell (11 sealing rings)
9. Silica gel bag
10.Mounting screws for the sensor (two screws included in the scope of delivery) and sensor
fixture (two screws)
11.Solid state relay (SSR)
2
3
5
4
6
10
7
8
9
1
11

2019-10
8
VPH-F200-T
Product Description
Front View
The key feature on the front of the VPH housing is the central protective panel. The protective
panel is embedded in the front of the upper shell. The protective panel provides an opening to
allow the chosen sensor module to capture positioning information and other data. The protec-
tive panel must be cleaned regularly to prevent the sensor from generating incorrect measure-
ments and error messages. When mounting the VPH housing, do not obstruct the sensing
range of the sensor.
Rear View
The rear of the VPH housing features cable glands for supplying electricity to the VPH housing
and the chosen sensor module. The number of cable glands used may vary depending on the
chosen sensor module. Unused cable glands must be fitted with a blind cap. The fan openings
are located underneath the cable glands.
Dimensions
Figure 3.2 Dimensions of the VPH housing
Caution!
Do not obstruct the air flow
The fan openings must remain uncovered and be kept clean. Do not insert objects into the fan
openings.
239
305
349

VPH-F200-T
Transport and Storage
2019-10
9
4 Transport and Storage
Retain the original packaging. Always store or transport the device in the original packaging to
protect it from electrostatic discharge (ESD) and mechanical damage.

2019-10
10
VPH-F200-T
Mounting
5 Mounting
Mounting the Sensor
. Loosen the 11 screws in the upper shell. Carefully lift up the upper shell. Place the upper shell
to one side.
2. Remove the silica gel bag from the inside of the housing.
3. Loosen the four screws in the sensor fixture.
Caution!
Malfunctions caused by condensation
Severe fluctuations in the ambient temperature can impair the sensor functionality.
•Avoid excessive temperature fluctuations to prevent condensation forming on the protec-
tive panel at the front of the VPH housing.
Note
The VPH housing is designed for horizontal mounting. Mounting the housing is an alternative
position is not permitted.
Caution!
Property damage caused by electrostatic discharge
f the housing is opened, the electronics may be damaged by electrostatic dis-
charges.
•Avoid electrostatic charges.
•Allow only qualified electricians to carry out work on the electrical compo-
nents.

VPH-F200-T
Mounting
2019-10
11
Figure 5.1 Mounting the sensor
4. Carefully lift the sensor fixture away from the connection board (1). Be careful with the cabling
connected to the sensor fixture.
5. nsert the sensor into the designated recess (2).
6. Using two screws (3), secure the sensor in place from underneath the sensor fixture.
7. Position the sensor fixture on the connection board on the housing base. Be careful with the
cabling connected to the sensor fixture.
3
1
2

2019-10
12
VPH-F200-T
Mounting
Figure 5.2 Securing the sensor fixture
8. Tighten the four screws (1) in the sensor fixture.
1

VPH-F200-T
Mounting
2019-10
13
Cabling
The cable gland comprises the modular SK NTOP ® CUBE system. The 40x40 mm seal insert
in the scope of delivery must be used for the power supply cable of the VPH housing. Various
other seal inserts in different sizes are available for the sensor supply. The appropriate blind
inserts must be fit into any unused space to achieve the designated protection class standards.
. Remove the upper shell to connect the cables.
2. Route the cables through the cable glands at the rear of the upper shell.
Figure 5.3 nstallation
Danger!
Danger to life due to electrical current
Making contact with live parts causes electric shocks, which pose an immedi-
ate danger to life.
•Allow only qualified electricians to carry out work on the electrical compo-
nents.
•Before working on electronic components, disconnect the power supply.
Note
A SK NTOP ® CUBE cable gland comprises two identical halves. The halves
are placed around the cable and they plug into each other so that the retaining
clips engage. These cable glands are inserted into the fixture and secured with
the retaining bracket.
Carry out these steps in reverse order to dismount the housing. To release the
cable gland from the cable, release the retaining clips on each half and then
pull the two halves apart.

2019-10
14
VPH-F200-T
Mounting
Figure 5.4 Removal

VPH-F200-T
Mounting
2019-10
15
Electrical Connection
The figure below shows the cabling of the climate control housing.
Figure 5.5 Connector assignment on the connection board
Connector assignment
The +24 VDC, GND, and PE connections at terminal -X1 represent the power supply of the cli-
mate protection housing and must be connected in line with the connection diagram above.
Apart from the fault monitoring function, the -X2 terminal is delivered fully connected.
The -X3 connection grounds the aluminum profile in the climate control housing. This connec-
tion is created via the mounting screws in the board. There is no need to make the connection
retrospectively.
Make sure that the SSR1, SSR2, and SSR3 markings refer to the terminals of the solid state
relay.
Caution!
Damage to the device
Connecting an alternating current or excessive supply voltage can damage the device or cause
the device to malfunction.
Electrical connections with reversed polarity can damage the device or cause the device to
malfunction.
Connect the device to direct current (DC). Ensure that the supply voltage rating is within the
specified device range. Ensure that the connecting wires on the single-ended female cordset
are connected correctly.
-VPH-F200-T_W1
YSLYCY
7x1,5
-VPH-F200-T_W2
LiY - CY
4x0,75
VPH-F200-T
/ Signal1_Switching Output
/ Signal2_Switching Output
/ Signal1_+
/ Signal2_+
VPH-F200-T_NC_5
Switch cabinet Clima Control Housing+A1
/ PE
/ L1
/ L0
-X1 PE62
1
2
-V1
-F1
U
-1
-4
+2
+3
-SSR1
230 V
power supply
provided by customer
-X10
1
2
PE
-X11
1
2
3
4
3
4
5
6
SH
SH
VPH-F200-T
_NC_6
Not used
Connection Board
-X1 1 2 -X2 1 2 -X2 10 113 4 5
Overtemperature
-Q1
Ventilator Fault
-Q2
+24VDC GND GND SSR1:+3 SSR1:+1
max.100mA max.100mA
-X3
24V/20A
B16A

2019-10
16
VPH-F200-T
Mounting
Fault Monitoring
The climate control housing has an integrated monitoring system for the fan function and the
excess temperature shut-off function. The respective fault is indicated via a potential-free
switching contact on terminal strip X2. There are also two red control LEDs on the inside of the
board to indicate the status. The table below describes the different switch states.
•Fault output 1 (terminal X2:11—X2:10) indicates that temperature monitoring has been
triggered
•Fault output 2 (terminal X2:2—X2:1) indicates that one or more fans have failed
To monitor the fault outputs, e.g., with a PLC, the following connection diagram must be
adhered to:
Figure 5.6 Connection diagram for PLC
Case of a fault Output Output 2 LED LED 2
Fan 2 is faulty Switched Blocked On Off
Fan 1 is faulty Switched Blocked On Off
Fan 1 and 2 are faulty Switched Blocked On Off
Excess temperature Blocked Switched Off On
1
2
3
4
5
+24 VDC
GND
PE
SSR 3
SSR 1
-X1
1
2
3
4
5
DO-2-
TACHO_FAN1
N_FAN1/2
P_FAN1/2
-X2
6
7
8
9
DO-2+
PN1
PP1
T_high
T_low
PE
PE
-X3
10
11
12
13
14
DO-1-
TACHO_FAN2
N_FAN1/2
P_FAN1/2
-X2
15
16
17
18
DO-1+
PN2
PP2
T_high
T_low
provided by
the customer
factory-
provided

VPH-F200-T
Mounting
2019-10
17
Solid State Relay Connections
The figure below shows how the solid state relay (SSR) is connected. The LED on the SSR
indicates the operating state of the SSR. f the LED is illuminated, this indicates that the SSR
output is connected and the VPH housing is in cooling mode. f the LED is not illuminated, this
indicates that the temperature in the VPH housing is below the limit value (+ 30 °C) or above
the upper limit value (+ 50 °C). The lower limit value is set to prevent the sensor from getting too
cold while the upper limit value is set to ensure the sensor does not overheat.
Figure 5.7 Solid State Relay Connections
Mounting the Solid State Relay
The SSR must be mounted in an open, easily accessible location in the switch cabinet using
the two mounting holes on the inside wall of the switch cabinet.
Figure 5.8 Dimensions of the solid state relay
1- +2
+3
4-
-X1.5 +24V
-X1.4
GND
INPUT
OUTPUT
LED
1- +2
+34-
44,52
61,31

2019-10
18
VPH-F200-T
Mounting
Cable Length
We recommend a maximum cable length of 25 m. The power supply must be readjusted as
shown in the figure below.
Figure 5.9 Voltage drop with a 1.5 mm
2
cable
Distance [s] = m
Value to be set on power supply [U] = V
0 5 10 15 20 25
30,00
28,00
26,00
24,00

VPH-F200-T
Mounting
2019-10
19
Setting the Read Distance
Before mounting the VPH housing, set the correct read distance for the chosen sensor. Pro-
ceed as follows:
Figure 5.10 Read distance
. Mount the sensor so that the lens of the read head with ring light and camera module is
pointing toward the Data Matrix code tape (1).
2. Align the read head at an orientation of 0 ° to the Data Matrix code tape.
3. During mounting, observe the maximum angle tolerances and check that they are not
exceeded. You can fine-tune the angle using the spring unit (4) on the mounting foot of the VPH
housing.
4. Check that the distance Z (2) from the read head to the Data Matrix code tape (1) is the same
as the read distance of the read head.
Note
The optimal read distance between the sensor and the Data Matrix code tape
is set out in the documentation provided with the chosen sensor. To find the
relevant documentation, visit our website at www.pepperl-fuchs.com. Simply
enter the product name or model number in the product/keyword field and
click the search button. Select your sensor from the list of search results and
click the Documentstab in the product information list. A list of all available
downloads is displayed.
1
Y
X
Z
0
2
3
4
233
47

2019-10
20
VPH-F200-T
Mounting
Once you have set the read distance, attach the VPH housing to the system using the
mounting foot.
Note
Note that the read distance of the sensor shifts by approx. 47 mm because the
first clearance hole in the mounting foot sits 47 mm behind the sensor (see the
figure above). We recommend that you measure the distances within the
device before mounting. You can fine-tune the distance to the Data Matrix
code tape by approx. ±2.5 mm using the three screws (3) on the mounting
foot.