Perle IOLAN SDG4 W User manual

IOLANSDG4WQuickStartGuide‐P/N5500416‐10(RevC)
IOLAN SDG4 W
Quick Start Guide
______________________________________________________________
Thisguidecoversbasicinstallationandconfigurationandisintendedforfirsttime
setuporproductevaluation.
Completedetailscanbefoundinthefollowingguidesatwww.perle.com/downloads.
 IOLANUser’sGuide
 IOLANCommandLineInterfaceReferenceGuide
 IOLANSDG4WHardwareInstallationGuide
What’s in the box?
 TheIOLANSDG4W
 QuickStartGuide(thisdocument)
 2XRPSMAantennae
 Poweradapter,strainreliefstrapandrubberfeet
 Wallmountbrackets
Hardware Overview


IOLANSDG4WQuickStartGuide‐P/N5500416‐10(RevC) 2
Button/SwitchFunctions
ResetButton
ToreboottheIOLANSDG4Winsertapaperclipintotheinsetholelabelledas
Resetandgentlypressinwardsandrelease.ThePower/ReadyLEDsontheIOLAN
SDG4WwillgoOnandthenmomentarilyOffwhenreleasedtoshowthattheunit
hasbeenrebooted.Ifyouholdtheresetbuttonbetween3and10seconds,the
IOLANSDG4Wwillresettheconfigurationtofactorydefault(eitherthePerleor
customdefaultconfiguration).Ifyouholdtheresetbuttongreaterthan10
seconds,thentheIOLANSDG4WwillresettheconfigurationtothePerlefactory
defaultconfiguration.
WPSButton
InsertapaperclipintotheinsetholelabelledasWPSandgentlypressinwards.
Pressingthisbuttonforlessthan3secondswillputtheIOLANSDG4WinWPS
mode,greaterthan4secondswillputtheunitinSoft‐APmode.
ConsoleSwitch
ThedipswitchontheIOLANSDG4Wissetinthefactorytoserial(downposition).
Unlessyouplantoattachaconsoletoserialport1oftheIOLANSDG4W,leave
thedipswitchintheserialposition
SerialPort
Pleaserefertothepin‐outtableintheIOLANSDG4WHardwareInstallation
Guideforyourdeviceandensureyouhavetheappropriatecableforconnecting
yourserialdevicestotheserialportsontheIOLANSDG4W.
Connecting the Hardware
Power
EitherthebarrelorTB(TerminalBlock)canbeusedtopowertheIOLANSDG4W.

Connectingthebarrelconnector
Plug the power adapter into a power socket and connect the barrel connector end
into the IOLAN SDG4 W. The Power/Ready LED should show a solid green.
Connectingtheterminalblockconnector
1. EnsurepowerisNOTappliedtothewirespriortoconnection.
2. Oneachendwire(12‐20AWG),removetheinsulationfromthecopperwire5
mm(3/16ofaninch).
3. Loosentheleftscrewonthetopoftheterminalconnectorblock,theninsert
yourpositive(+)wireintotheleftterminalandscrewitdowntight(.51Nm
torque).Loosentherightscrewonthetopoftheterminalconnectorblock,

IOLANSDG4WQuickStartGuide‐P/N5500416‐10(RevC) 3
theninsertyournegative(‐)wireintotherightterminalandscrewitdown
tight(.51Nmtorque).
4. Re‐inserttheterminalblockconnectorifremoved.
5. Connectthepowercordstrainrelief,ifdesired.SeeIOLANSDG4WHardware
Guidefordetails.
6. Connectthegroundinglug(notprovided)tothegroundingscrew,ifdesired.
SeeIOLANSDG4WHardwareInstallationGuidefordetails.
ConnectingtheAntennas,Ethernetcableandserialdevice
1. ConnecttheWi‐Fiantennabysimplyscrewingtheantennaontothe
connectorsontheIOLAN.
2. ConnecttheEthernetcable(Cat5/5e)fromtheRJ‐45plug(10/100/1000)to
theHUBorswitchthatwillprovidenetworkconnectivity(ifapplicabletoyour
application).
3. Connecttheserialdevicestotheserialports.SeetheSDG4WHardware
InstallationGuideforpinoutdetails.
Turnonpoweratsource.

Power-on Cycle
WhenthepowerisconnectedtotheIOLANSDG4W,thePower/ReadyLEDwill
cyclethroughseveralsequencesandwillendinasolidgreenoncetheunitisfully
bootedandreadytobeconfigured.IftheLEDisnotsolidgreenaftertwominutes,
seeIOLANSDG4WHardwareInstallationGuide.

LED Guide
SystemReady
 Greensolid—SystemReady
 Greenflashing—SystemisbootingorDIPswitchisinconsolemode
 Yellowflashing—Booting
 Red—Errorcondition.SeeIOLANSDG4WHardwareInstallationGuide
Link10/100/1000(onEthernetLinkConnector)
 Green—1000Mbps(flasheswithactivity)
 Green/Yellow—100Mbps(flasheswithactivity)
 Yellow—10Mbps(flasheswithactivity)
 Off—noLANconnection
WPS(Wi‐FiProtectedSetup)
 Yellowpulsing—ThefirstLEDwithinthesignalstrengthLEDdisplaywillpulse
yellowonandoff
Soft‐APMode(AccessPointMode)
 Greenpulsing—ThethirdLEDwithinthesignalstrengthdisplaywillpulse
greenonandoff

IOLANSDG4WQuickStartGuide‐P/N5500416‐10(RevC) 4
WLAN
 Greensolid—Awirelessconnectionhasbeenestablished
 Greenpulsing—Dataisbeingtransmittedoverthewirelessnetwork
 Off—Nowirelessconnectionisestablished
Signal
 WirelesssignalstrengthfromyellowLEDstogreenLEDswithgreenbeingthe
strongestsignalstrength.
Tx/Rx
 Flashing—Indicatestransmit/receiveserialactivity

Connecting to the IOLAN via the Wi-Fi Network
ThefollowingstepsallowforconnectiontotheIOLANforinitialconfiguration.
InitialSetup–UsingSoft‐APMethod
 TheIOLANSDG4Wmustbepoweredup.
 PresstheinsetWPSbutton(usingapaperclip)for4secondstoenableSoft‐
APmode.TheSignalstrengthLEDdisplayshouldshowapulsinggreenLEDon
thethirdlightfromthelefttorighttoconfirmyouareinSoft‐APmode.
 TheIOLANSDG4WislistedonyournetworkconnectionsonyourPCor
wirelessclient.ItwillappearasSSID:IOLAN‐xxxxxx(thelast6digitsofthe
IOLANwirelessMACaddress‐foundontheproductlabel).
 SelectthisSSIDonthePC.
 Whenapasswordisrequested,enterthepasswordprintedontheproduct
label.
 YoushouldnowbeconnectedtotheIOLAN’sWirelessinterface.
 UseaWebbrowsertoconnecttothedefaultaddressoftheIOLANSDG4W
at(192.168.0.1).
 Thedefaultuseridis“admin”andthedefaultpasswordis“superuser”(case
sensitive).
 YoucannowconfigureandmanageyourIOLANSDG4WusingtheIOLAN
WebManagerapplication.
Note:Youshouldchangetheadminpasswordtorestrictunauthorizedaccessto
yourIOLAN.
ForadditionalmethodsofconfiguringyourIOLAN(i.e.,DeviceManager,Telnet,
SNMP),pleaserefertotheIOLANUser’sGuide.

Registering the IOLAN
YoushouldregisterIOLANonlineat:
www.perle.com/support_services/warranty_reg.asp
Contacting Technical Support
ContactinformationforthePerleTechnicalAssistanceCenter(PTAC)canbefound
atthelinkbelow.
www.perle.com/support_services/support_request.shtm