Perlesmith PSLT9 User manual

V1.0
Model: PSLT9
TV Wall Mount
Instruction Manual
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to
provide you with the best quality products and services in the industry. Should you have
any issues, please don't hesitate to contact
AV Supply Group as below:
New Zealand | P: 6492749172 | E: [e-mail]
Australia | P: 61390714585 | E: [email protected]
Large Tilting Wall Mount for 42”– 85”TVs up to 75kg

IMPORTANT SAFETY INFORMATION
Check the VESA Pattern of TV Before the Installation
Weight Restrictions
DO NOT exceed the maximum weight indicated. This
mounting system is intended for use only within the
maximum weights indicated. Use with products heavier than
the maximum weights indicated may result in failure of the
mount and its accessories, causing possible injury.
WARNING
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
600 mm ≈ 23 5/8 in.
400 mm ≈ 15 3/4 in.
MAX:600mm/23.6 in.
MAX
:400mm/15.7 in.
Minimum VESA pattern:200mm/8 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 600x400 mm/23.6x15.7 in. or less
than VESA 200x100mm/8x4 in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[e-mail](NZ)/[email protected](AU) to find a
compatible mount.
165 lbs.
(75 kg)
If your TV weighs more, this
mount is NOT compatible.
Please carefully read all instructions before attempting installation. If you do not understand
the instructions or have any concerns or questions, please contact our customer service
at [e-mail](NZ) /[email protected](AU).
CAUT ION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete block and brick
walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and mount
combined.
01

7/32 in. (5.5 mm)
Wood Drill
3/8 in. (10mm)
Concrete Drill
1/2 in. (13mm)
Socket Wrench
Supplied Parts and Hardware for Step 1
Level
Tools Needed (Not lncluded)
Stud Finder Tape Measure Pencil Drill
Phillips Screwdriver
Hammer
x1
03
Left TV Bracket x1
04
Right TV Bracket
Spacers (if needed)
05 06
[B] x4
M6/M8
Washer
[C1] x8
φ8.5x18x2.5mm
[C2] x4
φ8.5x18x10mm
[C3] x4
φ8.5x18x22mm
Note: The spacers are shown in accordance with the
actual size
Warning:This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our customer
service at [e-mail](NZ)/[email protected](AU)
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware
02

x1
02
Wall Plate
Template
01 x1
Wall Plate
（Only one bolt size fits your TV）
TV Bolts07
[D1] x4
M6 x 15mm
[E1]
x4
M8 x 15mm
[E2]
x4
M8 x 35mm
[E3]
x4
M8 x 50mm
[D2]
x4
M6 x 35mm
M6
M8
Note: The bolts are shown in accordance with the actual size
Note: The lag screw is shown in accordance with the actual size
Washer
M8
A2
Lag Screw
M8x65mm
x4
x4
A1
Supplied Parts and Hardware for Step 2
03

x4
A3
Wall
Anchor
This anchor is for con-
crete or brick walls
ONLY. DO NOT use them in
drywall or wood studs.
CAUTION!
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We
recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Too Short Too Long Correct Correct
Only one bolt size fits your TV.
Step 1 Secure the TV Brackets to TV
M6 M8
Select TV Bolts
CAUTION: Ensure the TV brackets [03] and
[04] are EQUALLY CENTERED on your TV and
securely fastened in place.
UP
Please note: The bolt hole locations on your TV
may very in accordance of the manufacturers
design of the TV. We are only illustrating possible
locations of the bolt holes.
Please Note: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty understanding how to install
the TV bolts or spacers, please contact customer service at info@avsupply.-
co.nz(NZ)/[email protected](AU).
04 03
04

Option B (For Round Back TV)
Option C (For TV with A “Bump”)
Option A (For Flat Back TV)
05 B
Spacers may be necessary for 2 holes ONLY.
D1/E1
07
Alternate Spacer Setups
Alternate Spacer Setups
06
05
C2/C3
B
D2/E2/E3
07
06
05
C2/C3
B
D2/E2/E3
07
05 B
D1/E1
07
05

● Ensure the front support is securely fastened to the wall before
continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in.
(38 x 89 mm)
● Stud center must be verified
WARNING:
● Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly
against the front support.
● Do not use wall anchor [A3] for this step
Step 2
Step 2A
X
For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B
Attach Front Support to Wall
Wood Stud Option
Alternate Spacer Setups
Option D
For cable interference or inset holes, use
spacers to create extra space between the
TV and TV brackets
06
D2/E2/E3
07
C2/C3
06
04
B
05
06

2A-1
2A-2
2A-3
7/32 in. (5.5mm)
2 9/16 in. (65mm)
Position the wall plate template
[02] at your desired height and
line up the holes with your stud
center line. Level the template
and mark the holes.
Drill 4 pilot holes using a 7/32
in. (5.5mm) diameter drill bit.
Make sure the depth is not
less than 2 9/16 in. (65mm)
02
16 in.
(406mm)
24 in.
(609mm)
Use a stud finder(not included) to
locate wood studs or use an awl
(not included) to verify the edges.
Mark the edge and center
locations.
Awl
(Not lncluded)
07

WARNING:
● Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are
pulled firmly against the front support.
● Ensure the front support is securely fastened to the wall
before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16mm)
● Mount the front support directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks.
2A-4
Install the front support using lag screws [A1] and washers [A2]. Tighten
the lag screws [A1] only until the washers [A2] are pulled firmly against
the front support.
Step 2B
Wall
Anchor
A3
Solid Concrete or Concrete Block Option
A1 A2
1/2 in. (13mm)
Socket Wrench
(Not inclued)
08

2B-1 2B-2
3/8 in. (10mm)
2 3/4 in.(70mm)
Position the wall palte template [02] at
your desired height, level the wall plate
template and mark the pilot hole
locations.
Drill 4 pilot holes using a 3/8 in.
(10mm) diameter drill bit. Make
sure the depth is not less than 2
3/4 in. (70mm). Never drill into the
mortar between blocks.
2B-3
Use the hammer to
knock anchors [A3] into
the wall. Be sure the
anchors [A3] are
seated flush with the
concrete surface.
A1
A3
A2
Install the front support using lag screws [A1],
washers [A2] and anchors [A3]. Tighten the lag
screws [A1] only until the washers [A2] are pulled
firmly against the front support. DO NOT over-tighten
the lag screws [A1].
02
1/2 in. (13mm)
Socket Wrench
(Not inclued)
09