Perlesmith PSMFK13 User manual

Thank you for choosing this Perlesmith product! At Perlesmith
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.perlesmith.com/pages/reviews if
you are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA/DE/UK/FR/IT/ES/AU)
Website:
www.perlesmith.com
V1.0
Model:PSMFK13
TV Wall Mount
Instruction Manual

Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our Technical Support line at 1-800-556-6806 or customer service at
[email protected]
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, and concrete
block walls
• DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
MAX:400mm/16 in.
MAX:400mm/16 in.
Check the VESA Pattern of Your TV before the Installation
IMPORTANT SAFETY INFORMATION
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Verify Your Wall Construction
If you are are not sure the
wall construction, please
contact our product
support line at
1-800-556-6806 or
customer service at
[email protected]
Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)
If your TV VESA is greater than 400x400 mm/16x16 in. or less than VESA
75x75mm/3x3in., this mount is NOT compatible.
75 mm ≈ 3 in.
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
300 mm ≈ 11 3/4 in.
400 mm ≈ 15 3/4 in.

M6 x 20mm x4 M6 x 12mm x4
Spacer x4 M6 x8
F1 F2
F3 F4
BoltBolt
Nut
Warning:This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our Product
Support line at 1-800-556-6806 or customer service at
[email protected]
• Please note: Not all hardware included in this package will be used.
Awl
Stud Finder Tape Measure Pencil Drill
5/32 in.(4 mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
1/2in.(13mm)
Socket Wrench Screwdriver
Hammer
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Arm Assembly/Wall Plate
x1
01
TV Bracket
x4
02
3/8 in.(10mm)
Wrench

Spacers [if needed]
[Only one bolt size fits your TV]
04 05
M6
[B] x4
Washer
TV Bolts
06
M6 x 15mm
[D1] x4
M8 x 25mm
[E1] x4
M8 x 35mm
[E2] x4
M8 x 50mm
[E3] x4
M6 x 35mm
[D2] x4
M6
M8
L2.5mm
[C1] x8 L10mm
[C2] x4
L20mm
[C3] x4
Note: The bolts are shown in accordance with the actual size
Note: The spacers are shown in accordance
with the actual size
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Note: The lag screw is shown in accordance with the actual size
Lag Screw
M7x70mm [G]
x4
A1

Step 1 Secure the TV Plate to TV Bracket Assembly
3 in. (75mm)x3 in. (75mm)
4 in.(100mm)x4 in.(100mm)
8 in. (200mm)x8 in. (200mm)
12 in.(300mm)x12 in.(300mm)
16 in.(400mm)x16 in.(400mm)
3 in. (75mm)
4 in.(100mm)
3 in. (75mm)
4 in.(100mm)
Loosen the preassembled bolt [S] to detach the TV plate [a] from the arm
assembly/wall plate [01], and keep the preassembled bolt [S] for the use in step 5
①
②
a
S
Choose the Combination that Applies to Your VESA Hole Pattern
Option A
Option B
11 3/4 in.(300mm)
15 3/4 in.(400mm)
11 3/4 in.(300mm) 15 3/4 in.(400mm)
7 7/8 in.(200mm)
7 7/8 in.(200mm)
Wall
Anchor
x4
A2
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!

Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Note: If necessary, the spacers can be used in multi-layer. If the installation fails
after trying various methods, please contact customer service at
[email protected]
Too Short Too Long Correct Correct
F4
01
02
F2
F4
02
F1 F3
Adjust the width of the two vertical brackets
according to the width of the VESA pattern
holes.Then secure the other two brackets [02] to
the two horizontal brackets [02]with TV plate [a]
using bolts [F1], spacers [F3] and nuts [F4].
Secure the TV brackets [02] to the TV
plate [a] using bolts [F2] and nuts [F4].
M6 M8
Only one bolt size fits your TV.
Step 2 Secure the TV Plate or TV Plate with Brackets Assembly to TV
Select TV Bolts

CAUTION: Ensure the TV plate
assembly are EQUALLY CENTERED
on your TV and securely fastened in
place.
Option A (For Flat Back TV)
Option B (For Round Back TV)
05
04
06 D2/E2/E3
B
C1/C2/C3
04
06 D1/E1
B
05
C1/C2
（If Needed）
UP
Alternate Spacer Setups
Alternate Spacer Setups

D2/E2/E3
06
B
04
C1/C2/C3
05
06
04
B
D1/E1
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
Option D
For cable interference or inset holes, use spacers [05] to create extra space
between the TV and TV plate assembly
05
04
06 D2/E2/E3
B
C1/C2/C3
Alternate Spacer Setups
Alternate Spacer Setups
05
C1/C2
（If Needed）

Position the arm assembly/wall
plate [01] at your desired height
and line up the holes with your
stud center line. Level the arm
assembly/wall plate [01] and
mark the holes.
Step 3 Attach the Arm Assembly/Wall Plate [01] to Wall
WARNING:
16 in.(406mm)
Use a stud finder(not
included) to locate wood
studs or use an awl (not
included) to verify the
edges. Mark the edge
and center locations.
Awl
(Not lncluded)
3A-1
3A-2
Step 3A Wood Stud Option
X
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x
3½ in. (38 x 89 mm)
● Stud center must be verified
●Ensure the arm assembly/wall plate [01] is securely fastened to
the wall before continuing to the next step.
●DONOT USE ANCHOR [A2] FOR THIS STEP!
●Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly
against the wall plate.
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
HEAVY! You may need
assistance with this step.
If the stud is not quite well where you'd
like, please refer to the step 3A-3 in Page
09 (Horizontal Shift) to adjust the position
CAUTION!

3A-3-1
3A-3-2
3A-3-3
3A-3 Shift the Arm Assembly（If Needed）
To better position your mount and TV on your wall,the mount can be horizontal shifted
side to side by following these steps
Lossen the four preassembled bolts using wrench, and keep the four bolts for
use in the step 3A-3-3
Shift the arm assembly to your desired position.
Wrench
3/8 in.(10mm)
Wrench
3/8 in.(10mm)
Fasten the four bolts using wrench to fix the arm assembly to your desired
position.