Perlesmith PSXFK2 User manual

Thank you for choosing this Perlesmith product! At Perlesmith
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.perlesmith.com/pages/reviews if
you are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.perlesmith.com
TV Wall Mount
Instruction Manual V1.0
Model: PSXFK2

200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
300 mm ≈ 11 3/4 in.
600 mm ≈ 23 6/10 in.
800 mm ≈ 31 1/2 in.
MAX:800mm/31 in.
MAX:
600mm/24 in.
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our Technical Support line at 1-800-556-6806 or customer service at
[email protected]
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, and concrete
block walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H)
Check the VESA Pattern of Your TV before the Installation
Weight Restrictions
165 lbs.
(75 kg)
IMPORTANT SAFETY INFORMATION
DO NOT exceed the maximum weight
indicated. This mounting system is intended
for use only with the maximum weights
indicated. Use with products heavier than the
maximum weights indicated may result in
failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
If your TV weighs more, this
mount is NOT compatible.
If your TV VESA is greater than 800x600 mm/31x24 in. or less than VESA
200x100mm/8x4in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
01

Warning:This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our Product
Support line at 1-800-556-6806 or customer service at
[email protected]
• Please note: Not all hardware included in this package will be used.
Awl
Stud Finder Tape Measure Pencil Drill
7/32 in.(5.5 mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
1/2 in.(13mm)
Socket Wrench Screwdriver
Hammer
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
TV Bracket
x2
03
Spacers [if needed]Washers
06 07
M8
[B] x4
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Verify Your Wall Construction
If you are not sure the wall
construction, please
contact our product
support line at
1-800-556-6806 or
customer service at
[email protected]
[C1] x8
φ8.5x18x2.5mm
[C2] x4
φ8.5x18x10mm
[C3] x4
φ8.5x18x22mm
02

[Only one bolt size fits your TV]
TV Bolts
M6 x 15mm
[D1] x4
M6 x 35mm
[D2] x4
M8 x 15mm
[E1] x4
M8 x 25mm
[E2] x4
M8 x 50mm
[E4] x4
M6
M8
Note: The bolts are shown in accordance with the actual size
M8 x 35mm
[E3] x4
08
Supplied Parts and Hardware for Step 2
01 x1
Arm Assembly/Wall Plate Level x1 Wall Plate Template
05 x1
03

Only one bolt size fits your TV.
Step 1 Secure the TV Brackets to TV
Select TV Bolts
M6 M8
Note: The lag screw is shown in accordance with the actual size
Washer
M8
A2
Lag Screw
M8x65mm
x6
x6
A1
Wall
Anchor
x6
A3
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
Supplied Parts and Hardware for Step 3 to Step 4
04 x2
End Cap
02 x1
Front Support Wrench x1
04

Option A (For Flat Back TV)
Option B (For Round Back TV)
07
06
08 D2/E2/E3/E4
B
C1/C2/C3
06
08 D1/E1
B
UP
CAUTION: Ensure the TV brackets
[03] are EQUALLY CENTERED on your
TV AND securely fastened in place.
03
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Note: If necessary, the spacers can be used in multi-layer. If the installation fails
after trying various methods, please contact customer service at
[email protected]
Too Short Too Long Correct Correct
Alternate Spacer Setups
05

D2/E2/E3/E4
08
B
06
C1/C2/C3
07
06 B
08 D1/E1
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
Option D
For cable interference or inset holes, use spacers [07] to create extra space
between the TV and TV brackets
06
08 D2/E2/E3/E4
B
C1/C2/C3
07
Alternate Spacer Setups
Alternate Spacer Setups
06

16 in.(406mm)
24 in.(609mm)
WARNING:
Step 2
For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B
Attach the Arm Assembly/Wall Plate [01] to Wall
Step 2A Wood Stud Option
X
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x
3½ in. (38 x 89 mm)
● Stud center must be verified
●Ensure the arm assembly/wall plate [01] is securely fastened to
the wall before continuing to the next step.
●DONOT USE ANCHOR [A3] FOR THIS STEP!
●Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are
pulled firmly against the wall plate.
2A-1
2A-2
Use a stud finder(not included) to
locate wood studs or use an awl
(not included) to verify the edges.
Mark the edge and center locations.
Position the wall plate template
[05] at your desired height and
line up the holes with your stud
center line. Level the wall plate
template [05] and mark the
holes.
05
Awl
(Not lncluded)
07

WARNING:
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly
against the wall plate.
●Ensure the arm assembly/wall plate [01] is securely fastened to the
wall before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Wall
Anchor
A3
Step 2B Solid Concrete or Concrete Block Option
2A-3
2A-4
ø7/32 in.(5.5 mm)
2 9/16 in.(65mm)
1/2 in.(13mm)
Socket Wrench
(Not included)
Drill 4 pilot holes using a 7/32 in.(5.5
mm) diameter drill bit. Make sure the
depth is not less than 2 9/16 in.(65mm).
Install the arm assembly/wall plate
using lag screws [A1] and washer
[A2]. Tighten the lag screws [A1] only
until the washers [A2] are pulled
firmly against the wall plate.
A2
01
A1 A2
You may need
assistance with this step.
08

ø3/8 in.(10mm)
2 3/4 in.(70mm)
Drill 6 pilot holes using a 3/8
in.(10mm)diameter drill bit. Make sure
the depth is not less than 2 3/4
in.(70mm). Never drill into the mortar
between blocks.
1/2 in.(13mm)
Socket Wrench
(Not included)
Use the hammer to knock anchors
[A3] into the wall. Be sure the
anchors [A3] are seated flush with
the concrete surface.
Install arm assembly/wall plate
using lag screws [A1], washers
[A2] and anchors [A3]. Tighten
the lag screws [A1] only until the
washers [A2] are pulled firmly
against the wall plate. DO NOT
over-tighten the lag screws [A1].
2A-1
2A-2
2A-3
2A-4
05
Position the wall plate template
[05] at your desired height, level
the wall plate template and mark
the pilot hole locations.
A1 A2
A2
01
You may need
assistance with this step.
09

Step 3 Secure Front Support to Arm Assembly Wall Plate
Remove the preassembled
bolts [S2] and save to
use, then raise the safety
locks.
Press the safety locks
down.
Then fasten the bolts [S2].
Hang the TV with brackets [03] onto the
front support [02]
3-1
Install the end caps [04] to front support [02] with the
preassembled bolts [S].
S
Step 4 Hang TV with Brackets [03] onto the Front Support [02]
3-2
Secure the front support [02] to arm assembly/wall plate [01]
using preassembled bolts [S1] and washers [W]
Make sure the big button in Front
Support [02] hangs on the hook of the
arm assembly/wall plate.
Wrench
02
02
01
W
S1
04
Loosen the preassembled bolts [S1] and washers
[W] from the back of front support assembly,
and keep them for use in step 3-2.
Screwdriver
(Not lncluded)
Wrench
Screwdriver
(Not lncluded)
or
or
S1
W
You may need
assistance with this step.
10

！
Loosen
！
Tighten
Tilt Nut
T
1. Loosen four tilt nuts [T].
2. Adjust TV to your desired tilt angle.
3. Retighten both tilt nuts [T] to fix the tilt angle.
1. Loosen the two bolts [S1] on the rear of the front support.
2. Level your TV.
3. Retighten both bolts [S1] to hold TV in place.
Step 5 Adjustments
Tilt Adjustments
Level Adjustment
S1 S1
Level the TVLossen 2 bolts [S1] Tighten 2 bolts [S1]
or or
Wrench
Screwdriver
(Not lncluded)
11