Philio PAT12-A User manual

Z-Wave CO2 Sensor PAT12-A/B
The PAT12 CO2 sensor uses advanced NDIR (Non Dispersive Infra-Red) detect
technolo y. The major advanta es of NDIR sensors are low life cycle cost and
precise and stable lon -term operation.
The PAT12 CO2 sensor is a device that allows you to check the air quality in your
home by detectin and measurin CO2 concentrations.
The PAT12 sensor is easy to use and very convenient for your home. Just set the
sensor on the wall in the rooms you would like to control, and you are ready to o.
Moreover, the PAT12 can be inte rated to other Z-Wave certified devices, and
controlled with Philio app “Home Mate 2.” You can now protect your family and your
business and make sure that air you are breathin is safe. Set up your PAT12 to send
re ular notifications and take control even when not at home.
This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-
Wave Plus messa es to communicate to other security enabled Z-Wave Plus
products.
This device must be used in conjunction with a Security Enable Z-Wave Controller in
order to fully utilize all implemented functions.
The device adopts the Z-WaveTM 500 series chip when your Z-WaveTM network
system is made by Z-WaveTM 500 series devices. This network system has the
followin advanta es:
The product supports the Over The Air (OTA) feature for the products firmware
up rade.
Notice:
The PAT12 may exhibit a tolerance addition of 90ppm when first installed. This will et
corrected by the Self Calibration Feature within the first weeks of operation.
Please continue to operate the PAT12 at a condition that was exposed, ambient
reference levels of air at 400 ppm CO2, for at least 7-Days.
Openin external windows can drop the CO2 levels down to 400ppm.
Function Compare A/B
CO2 Accuracy
PAT12-A +/- 75 ppm or 10% of readin , whichever is reater
PAT12-B +/- 30 ppm or 3% of readin , whichever is reater
1

Addin to Z-WaveTM Network
This product can be operated in any Z-Wave network with other Z-Wave certified de-
vices from other manufacturers. All non-battery operated nodes within the network will
act as repeaters re ardless of vendor to increase reliability of the network.
The table below lists an operation summary of basic Z-Wave functions. Please refer
to the instructions for your Z-WaveTM Certificated Primary Controller to access the
Setup function, and to Add/Remove/associate devices
Function Description Annotation
No node ID The Z-Wave Controller does not
allocate a node ID to the Switch.
LED li ht will flash for
120 seconds.
Add (Inclusion) 1. Set your Z-Wave controller
into inclusion mode by
followin the instructions
provided by the controller
manufacturer.
2. Press the include button of
the PAT12 three times within
3 seconds to enter inclusion
mode.
If the learnin code is
successful, the LED
li ht will flash slowly.
Remove (Exclusion) 1. Set your Z-Wave controller
into exclusion mode by
followin the instructions
provided by the controller
manufacturer.
2. Press the include button of
the PAT12 three times within
3 seconds to enter exclusion
mode.
3. Node ID has been excluded.
If the remove
successful,the LED
li ht will flash for 120
seconds.
Reset 1. Press the include button of Use this procedure only
the PAT12 three times within
3 seconds to enter inclusion
mode.
2. Within 1 second, a ain press
the include button of the
PAT12 for 5 seconds.
3. IDs will et excluded.
*notice1:Please use this
procedure only when the
network primary controller is
missin or otherwise
inoperable.
in the event that the
primary controller is
lost or otherwise
inoperable.
SmartStart 1. Product has a DSK strin ,
you can key in the first five
di its to be in with the smart
start process, or you can scan
QR code.
2. SmartStart enabled products
can be added into a Z-Wave
network by scannin the Z-
Wave QR Code present on
the product with a con-troller
providin SmartStart inclu-
sion. No further action is
required and the SmartStart
product will be added
automatically within 10 min-
utes of bein switched on in
the net-work vicinity.
*notice1:The QR code can be
foundon the device PAT12 or
in the box.
If the learnin code is
successful, the LED
li ht will flash slowly.
2

Association This machine provides a roup of
nodes. Each roup can set 5 Nodes.
Group 1: Used for returned events.
Report type:
1.Notification report
2.Sensor multilevel report
3.Rest report
※Addin a node ID allocated by Z-Wave Controller means inclusion. Removin a
node ID allocated by Z-Wave Controller means exclusion.
※Failed or success in includin /excludin the node ID can be viewed from the Z-
Wave Controller.
LED Indication
To distin uish what mode the switch is in, view the LED li ht description for
identification.
State Type LED Indication
No node ID Under normal operation, when the Switch has not been allocated a
node ID, the LED li ht will flash on and off alternately at 120 second
intervals. By pressin On/Off button, the li ht will stop flashin
temporarily.
Learnin When the PAT12 is in learnin mode, if the learnin code is success-
ful, the LED li ht will flash slowly.
Z-Wave Messa e Report
*CO2 Report:
When the CO2 Concentration differential over 1 percent(in default) or across the
baseline level , the device will unsolicited to send the “ Sensor Multilevel Report ” to
the nodes in the roup 1.
Multilevel Sensor Report
Sensor Type : CO2 (0x11)
Note:
1.This function default is enabled, to disable this function by settin the confi uration
NO.2 to zero.
2.Baseline level default is disable, to enable this function by settin the confi uration
NO.3、NO.4、NO.5、NO.6、NO.7.
*Tamper Report:
The tamper key pressed over 8 seconds.The device will into the alarm state. In that
state, if the tamper key be released, the device will unsolicited to send the report to
the nodes in the roup1.
Notification Report
Notification Type : Home Security (0x07)
Event : Tamperin . Product coverin removed (0x03)
*Timin Report:
•CO2 report: Every 1 hours report once in default.
It could be chan ed by settin the confi uration NO.1.
Over The Air (OTA) Firmware Update
The device supports Z-Wave firmware update via OTA.
3

Before startin the update, please remove the front case of the device otherwise the
hardware check will fail.
Let the controller into firmware update mode, and press the front tamper key once to
start the update.
After firmware download is complete, the LED li ht will flash intermittently.
Z-Wave Supported Command Classes
The device supports the security function.when the device include with
a security controller, the device will auto switch to the security mode.In
the security mode, the follow commands need usin Security CC
wrapped to communicate.
Command Class Version Required Security Class
Z-Wave Plus Info 2 None
Association 2 Hi hest ranted Security Class
Association Grp Info 1 Hi hest ranted Security Class
Transport Service 2 None
Version 3 Hi hest ranted Security Class
Manufacturer Specific 2 Hi hest ranted Security Class
Device Reset Locally 1 Hi hest ranted Security Class
Powerlevel 1 Hi hest ranted Security Class
Security 2 1 None
Confi uration 1 Hi hest ranted Security Class
Notification 8 Hi hest ranted Security Class
Security 0 1 None
Sensor Multilevel 11 Hi hest ranted Security Class
Supervision 1 None
Firmware Update Meta Data 4 Hi hest ranted Security Class
Z-Wave Confi uration Settin s
NO. Name Size
(Byte) Valid Def. Description
1Auto report CO2 Concentra-
tion time 2 1~32767 60 Units of 1 minute.
2CO2 Concentration differen-
tial report 1 0~100 10
Units of 1 %.
0 means turn off the report
3 Baseline level 1 1 0~50 0
Units of 100 ppm.
0 means turn off the report
4 Baseline level 2 1 0~50 0
Units of 100 ppm.
0 means turn off the report
5 Baseline level 3 1 0~50 0
Units of 100 ppm.
0 means turn off the report
6 Baseline level 4 1 0~50 0
Units of 100 ppm.
0 means turn off the report
7 Baseline level 5 1 0~50 0
Units of 100 ppm.
0 means turn off the report
4

Overview
Specification
Rated Volta e DC 5V/1A from USB
Ran e Minimum 40M in door and 100M in outdoor line of
si ht
Operatin Temperature -10°C ~ 40°C (85% humidity)
Stora e Temperature -20 C ~ 60°C
Location Indoor use only
Dimension 65(L) x 44.1 (W) x 56.3 (H) mm
CO2 65535ppm
Frequency Ran e 868.40MHz; 869.85MHz (EU)
908.40MHz; 916.00MHz (USA/Canada)
916MHz (Israel)
922.5MHz, 923.9MHz, 926.3MHz (JP)
RF Maximum Power (peak) +5dBm (peak)
RF Maximum Power
(Avera e)
-10dBm (Avera e)
RF Modulation Type FSK (Frequency-Shift Keyin )
FCC ID RHHPAT12
Disposal
This markin indicates that this product should not be disposed with
other household wastes throu hout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recyclin .
Philio Technolo y Corporation
8F., No.653-2, Zhon zhen Rd., Xinzhuan Dist., New Taipei City 24257, Taiwan
www.philio-tech.com
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
di ital device, pursuant to Part 15 of the FCC Rules. These limits are desi ned to
5

provide reasonable protection a ainst harmful interference in a residential installation.
This equipment enerates, uses and can radiate radio frequency ener y and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no uarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turnin the equipment off and on, the user is encoura ed to try to correct the
interference by one of the followin measures:
•Reorient or relocate the receivin antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
followin two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, includin interference that may
cause undesired operation.
FCC Caution: Any chan es or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operatin in conjunction with any other
antenna or transmitter.
Warnin
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities. Contact your local overnment for information re ardin the
collection systems available. If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the roundwater and et into the food
chain, dama in your health and well-bein .
When replacin old appliances with new once, the retailer is le ally obli ated to take
back your old appliance for disposal at least for free of char e.
6