Philio PST07 User manual

3 in 1 Multi Sensor
PST07
PST07-A PST07-B
PST07-C PST07-D
The multi-sensor PST07 has PIR, temperature and light sensors
function in one, based on Z-WaveT technology.
The multi sensor is a Z-WaveT enabled device which is fully compatible
with any Z-WaveT enabled network. This device is a security enabled
Z-Wave Plus product that is able to use encrypted Z-Wave Plus
messages to communicate to other security enabled Z-Wave Plus
products. Z-WaveT enabled devices displaying the Z-WaveT logo can
also be used with it regardless of the manufacturer, and ours can also
be used in other manufacturer’s Z-WaveT enabled networks.
The product supports ver The Air( TA) feature for the products
firmware upgrade.
This product can be included and operated in any Z-WaveT network
with other Z-WaveT certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-WaveT 500 series chip, when your Z-WaveT
network system is all made by Z-WaveT 500 series devices. The
network system will have the advantages as below.
•Concurrent multi-channel support reduces external interference.
•Better RF range, improve about 10 meters in indoor.
•Support 100 Kbps transmit speed, speed up communication.
Specification
Rated DC3V (CR123A)
RF distance in. 40 indoor,
100 outdoor line of sight,
RF Frequency 868.40 Hz, 869.85 Hz(EU)
1

908.40 Hz, 916.00 Hz(US)
920.9 Hz, 921.7 Hz,
923.1 Hz(TW/SG/Thai/KR)
RF aximum Power +5dBm
ALS Sensing Range 0-10000 lux
Temperature Sending Range -10 to 40° C
Dimension 89*83*62
Weight 91.4g (PST07-A),
96.0g (PST07-D)
IP classification IPX4
Operation temperature -10 to 40° C
FCC ID RHHPST07
arking CE/NCC
Specifications are subject to change and improvement without
notice.
Function Compare A/B/C/D
odel Description
PST07-A Wall mount
PST07-B Ceiling mount with Square shape
PST07-C Ceiling mount with Round shape
PST07-D Wall mount with lens cover
Troubleshooting
Symptom Cause of Failure Recommendation
The device can not
join to Z-Wave™
network
The device may in a Z-
Wave™ network.
Exclude the device
then include again.
For Instruction to http:// www.philio-tech.com
overview
2

Add to/Remo e from Z-Wa eTM Network
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-WaveT network.
The table below lists an operation summary of basic Z-Wave functions.
Please refer
to the instructions for your Z-WaveT Certificated Primary Controller to
access the
Setup function, and to Add/Remove/associate devices
Notice: Including a node ID allocated by Z-WaveT Controller means
“Add” or “Inclusion”. Excluding a node ID allocated by Z-WaveT
Controller means “Remo e” or “Exclusion”.
Function Description
Add
1. Have Z-WaveT Controller entered inclusion mode.
2. Pressing tamper key three times within 2 seconds
to enter the inclusion mode.
3. After add successful, the device will wake to
receive the setting command from Z-WaveT
Controller about 20 seconds.
Remove
1. Have Z-WaveT Controller entered exclusion mode.
2. Pressing tamper key three times within 2 seconds
to enter the exclusion mode.
Node ID has been excluded.
Reset
Notice: Use this procedure only in the e ent
that the primary controller is lost or
otherwise inoperable.
1. Pressing button four times and keep about 5
seconds.
2. IDs are excluded and all settings will reset to
factory default.
SmartStart
1. Product has a DSK string, you can key in first five
digit to increment smart start process, or you can
scan QR code.
2. SmartStart enabled products can be added into a
Z-Wave network by scanning the Z-Wave QR Code
present on the product with a controller providing
SmartStart inclusion. No further action is required
and the SmartStart product will be added automati-
cally within 10 minutes of being switched on in the
network vicinity.
*notice1:The QR code can be found on the device
or in the box.
Association
3. Have Z-WaveT Controller entered association
mode.
4. Pressing tamper key three times within 1.5 seconds
to enter the association mode.
Note: The device support 2 groups. The group 1 is for
receiving the report message, like triggered event,
temperature, illumination etc. The group 2 is for light
control, the device will send the “Basic Set” command
to this group. A group one support 1 nodes maximum
and group two support 5 nodes maximum.
•Failed or success in add/remove the node ID can be viewed
from Z-WaveT Controller.
3

Notice 1: Always RESET a Z-WaveT device before trying to add it to a
Z-WaveT network
Z-Wa eTM Notification
After the device adding to the network, it will wake-up once per day in
default. When it wake-up it will broadcast the “Wake Up Notification”
message to the network, and wake-up 10 seconds for receive the
setting commands.
The wake-up interval minimum setting is 30 minutes, and maximum
setting is 120 hours. And the interval step is 30 minutes.
If the user want to wake-up the device immediately, please remove the
front cover, and press the tamper key once. The device will wake-up 10
seconds.
Z-Wa eTM Message Report
When the PIR motion triggered, the device will report the trigger event
and also report temperature and illumination level.
* Motion Report:
When the PIR motion detected, the device will unsolicited to send the
report to the nodes in the group 1.
Notification Report (V8)
Notification Type: Home Security (0x07)
Event: otion Detection, Unknown Location (0x08)
* Tamper Report:
The tamper keys are pressed over 5 seconds. The device will into the
alarm state. In that state, if any one of the tamper keys be released,
the device will unsolicited to send the report to the nodes in the group
1.
Notification Report (V8)
Notification Type: Home Security (0x07)
Event: Tampering. Product covering removed (0x03)
* Temperature Report:
When the PIR motion detected state changed, the device will
unsolicited to send the “Sensor ultilevel Report” to the nodes in the
group 1.
Sensor Type: Temperature (0x01)
*** Temperature differential report ***
This function default is enabled, to disable this function by setting the
configuration NO.12 to 0.
In the default, when the temperature is changed to plus or minus one
degree Fahrenheit (0.5 degree Celsius), the device will report
temperature information to the nodes in the group 1.
Caution 1: Enable this functionality, it will cause the PIR otion to
disable detection when the temperature measurement. In other words,
The PIR motion will blind one second in every one minute.
* LightSensor Report:
When the PIR motion detected state changed, the device will
unsolicited to send the “Sensor ultilevel Report” to the nodes in the
group 1.
Sensor Type: Luminance (0x03)
*** LightSensor differential report ***
This function default is disabled, to enable this function by setting the
configuration NO.13 not to zero.
And if the LightSensor is changed to plus or minus the value (setting by
the configuration NO.13), the device will report illumination information
to the nodes in the group 1.
Caution 1: Enable this functionality, it will cause the PIR otion to
disable detection when the illumination measurement. In other words,
The PIR motion will blind one second in every one minute.
4

* Timing Report:
Beside the event triggered could report message, the device also
support the timing unsolicited report of the status.
•Battery level report: Every 6 hours report once in default.
It could be changed by setting the configuration NO. 8.
•Low battery report: When the battery level is too low. (Lose
battery report when a power-on or PIR trigger.)
•LightSensor level report: Every 6 hours report once in default.
It could be changed by setting the configuration NO. 9.
•Temperature report: Every 6 hours report once in default.
It could be changed by setting the configuration NO. 10.
Notice: The configuration NO. 8 could be setting to zero to disable
the auto report. And the configuration NO. 11 could change the tick
interval, the default value is 30, if setting to 1, that means the
minimum auto report interval will be one minute.
Power Up Procedure
* Battery Power Check
When the device power up, the device will detect the power level of the
battery immediately. If the power level is too low, the LED will continue
flash about 5 seconds. Please change another new battery.
* Wake
When the device power on, the device will wake about 20 seconds. In
this duration, the controller can communicate with the device. Normally
the device is always sleeping to save the battery energy.
Security Network
The device support the security function. When the device included
with a security controller, the device will auto switch to the security
mode. In the security mode, the follow commands need using Security
CC wrapped to communicate, otherwise it will not response.
CO AND_CLASS_VERSION_V3
CO AND_CLASS_ ANUFACTURER_SPECIFIC_V2
CO AND_CLASS_DEVICE_RESET_LOCALLY
CO AND_CLASS_ASSOCIATION_V2
CO AND_CLASS_ASSOCIATION_GRP_INFO
CO AND_CLASS_POWERLEVEL
CO AND_CLASS_CONFIGURATION
CO AND_CLASS_NOTIFICATION_V8
CO AND_CLASS_FIR WARE_UPDATE_ D_V4
CO AND_CLASS_BATTERY
CO AND_CLASS_SENSOR_ ULTILEVEL_V11
CO AND_CLASS_WAKE_UP_V2
Operation Mode
There are two modes “Test” and “Normal”. “Test ode” is for the user
test the sensor function when installation.“Normal ode” is for the
normal operation.
Operation ode can be switched by pressing button or tamper key two
times. LED can indicate which mode it is. Lighting on one second
means entering test mode, flashing once means entering normal mode.
When the event triggered, normally the LED won't indicated, unless the
battery is in the low level, the LED will flash once. But in the “Test
ode” the LED also will light ON one second.
When the event triggered, the device will emit the signal to turn ON
the lighting equipment, those nodes are in the group 2. And delay a
while to turn OFF the lighting equipment. The delay time is setting by
the configuration NO. 7.
The PIR motion re-detected interval, in the “Test ode” fixed to 10
seconds. In the “Normal ode”, it according to the setting of the
configuration NO. 6.
5

Choosing a Suitable Location
1. The recommended mounting height is 160cm
2. Don't let the device facing the window or the sunlight.
3. Don't let the device facing the source of heat. For instance the
heater or the air-condition.
Battery Installation
When the device reports the low battery message, users should
replace the battery. The battery type is CR123A, 3.0V.
6

Z-Wa e Configuration Settings
NO
.Name Def. Valid Description
1Basic Set
Level 99 0 ~ 99
Setting the BASIC command value to turn
on the light. The 0x63 means turn on
the light. For dimmer equipment 1 to 99
means the light strength.
0 means turn off the light.
3PIR
Sensitivity
80 0 ~ 99
PIR sensitivity settings.
0 means disable the PIR motion.
1 means the lowest sensitivity,
99 means the highest sensitivity.
High sensitivity means can detected long
distance, but if there is more noise signal
in the environment, it will re-trigger too
frequency.
4 Operation
ode 0x31 All Operation mode. Using bit to control.
1Bit0: Setting the temperature scale. (1:
Fahrenheit, 0:Celsius)
0Bit1: Reserve.
0Bit2: Reserve.
0Bit3: Reserve.
1
Bit4: Disable the illumination report after
event triggered.
(1:Disable, 0:Enable)
1
Bit5: Disable the temperature
report after event triggered.
(1:Disable, 0:Enable)
0Bit6: Reserve.
NO
.Name Def. Valid Description
0Bit7: Reserve.
5Customer
Function
3All Customer function switch, using bit
control.
1Bit0: Tamper On/Off (1:On, 0:Off)
1Bit1: Red LED On/Off (1:On, 0:Off)
0
Bit2: otion Off.(1:On, 0:Off)
Note: Depends on the Bit2,
1: Report Notification CC,
Type: 0x07, Event: 0xFE
0Bit3: Reserve.
0Bit4: Reserve.
0Bit5: Reserve.
0Bit6: Reserve.
0Bit7: Reserve.
6
PIR Re-
Detect
Interval
Time
61 ~ 60
In the normal mode, after the PIR motion
detected, setting the re-detect time. 10
seconds per tick, default tick is 6 (60
seconds).
Setting the suitable value to prevent
received the trigger signal too frequently.
Also can save the battery energy.
Notice: If this value bigger than the
configuration setting NO. 7 There is a
period after the light turned off and the
PIR not start detecting.
7Turn Off
Light Time
71 ~ 60 After turn on the lighting, setting the
delay time to turn off the lighting when
the PIR motion is not detected. 10
7

NO
.Name Def. Valid Description
seconds per tick, default tick is 7 (70
seconds).
0 means never send turn off light
command.
8Auto Report
Battery Time 12 0 ~ 127
The interval time for auto report the
battery level.
0 means turn off auto report battery.
The default value is 12. The tick time can
setting by the configuration No.11.
9
Auto Report
LightSensor
Time
12 0 ~ 127
The interval time for auto report the
illumination.
0 means turn off auto report illumination.
The default value is 12. The tick time can
setting by the configuration No.11.
10
Auto Report
Temperature
Time
12 0~ 127
The interval time for auto report the
temperature.
0 means turn off auto report temperature.
The default value is 12. The tick time can
setting by the configuration No.11.
11 Auto Report
Tick Interval 30 0 ~ 0xFF
The interval time for auto report each tick.
Setting this configuration will effect
configuration No.8, No.9 and No.10.
The unit is 1 minute.
12 Temperature
Differential
Report
21~100 The temperature differential to report.
0 means turn off this function.
The unit is 0.5 Fahrenheit.
Enable this function the device will detect
per minutes.
And when the temperature is over 140
NO
.Name Def. Valid Description
degree Fahrenheit, it will continue report.
Enable this functionality will cause some
issue please see the detail in the
“Temperature Report” section.
13
LightSensor
Differential
Report
20 1~100% The LightSensor Differential to report.
0 means turn off this function.
The unit is percentage.
Enable this function the device will detect
every percentage.
And when the lightSensor is over 20
percentage, it will continue report.
14 PIR Trigger
ode 11~3
PIR Trigger ode:
ode1: Normal
ode2: DayTime
ode3: AtNight
15 PIR
NightLine 21~ 10000
PIR night line Lux conditions:
LightSensor determines whether
the level is night. (Unit 1Lux)
Z-Wa e Supported Command Class
Command Class Version Required Security Class
Z-Wave Plus Info 2 None
Version 3 Highest granted Security Class
Manufacturer Specific 2 Highest granted Security Class
Security 2 1 None
8

Device Reset Locally 1 Highest granted Security Class
Association 2 Highest granted Security Class
Association Group Information 1 Highest granted Security Class
Powerlevel 1 Highest granted Security Class
Basic 1 Highest granted Security Class
Configuration 1 Highest granted Security Class
Notification 8 Highest granted Security Class
Firmware Update eta Data 4 Highest granted Security Class
Supervision 1 None
Transport Service 2 None
Battery 1 Highest granted Security Class
Sensor multilevel 11 Highest granted Security Class
Wake up 2Highest granted Security Class
FCC ID: RHHPST07
Disposal
This marking indicates that this product should not be
disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the
return and collection systems or contact the retailer where
the product was purchased. They can take this product for
environmental safe recycling.
Philio Technology Corporation
8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City
24257, Taiwan(R.O.C)
http://www.philio-tech.com
FCC Interference Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
9

•Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Warning
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities. Contact your local government for
information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging
your health and well-being.
When replacing old appliances with new once, the retailer is legally
obligated to take back your old appliance for disposal at least for free
of charge.
警語:
「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使 者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
低功率射頻器材之使 不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停 ，並改善至無干擾時方得繼續使 。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通
信或工業、科學及醫療 電波輻射性電機設備之干擾。」
i
10