Philip Payne SPRITE 870 Series User manual

Surface Ceiling IP20 Class 1 SPRITE 870 Series
Emergency Downlighter
Dimensions
252
160
48 200 CENTRES
50
CENTRES
36
CENTRES
36
CENTRES
Ø5 FIXING HOLES
Ø20
CABLE ENTRY
Ø20KNOCKOUT (THIS SIDE ONLY)
15
Connections
USLN
DALIDALI
N
NM3
AutoTest DALI
USL
SPRT870LN
220-240V AC 50/60 Hz
NM3
SPRT870YS
220-240V AC 50/60 Hz
NM3 AutoTest
SPRT870DS
220-240V AC 50/60 Hz
DALI
NM3
Maximum luminaires on a
Type B, 10A circuit breaker
90 luminaires
90 luminaires
90 luminaires
Supply voltageDownlighter features Part No.
Do not stare at operating lamp.
It may be harmful to the eyes.
Basic insulation between L/N and
DALI/DALI terminals.

Important-Safety
Before carrying out any servicing on this luminaire, ensure that the mains supply is fully isolated.
Disconnect luminaire before insulation testing of the installation.
Installation Method
Philip Payne Ltd
A SUBSIDIARY OF F.W. THORPE PLC
Thornhill Road, Solihull, B91 2HB, England.
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]
Website: http://www.philippayne.co.uk
Philip Payne Ltd registered in England No. 1361523 ISO9001
FM55077 21LFT053_4
Operation and Maintenance
Continual operation at mains voltages in excess of the rated voltage will reduce LED and expected gear life.
This luminaire uses plastic components in its construction and when installed in environments containing chemicals, degradation may occur.
Please contact our Technical Department for advice.
Modifications
Philip Payne products should not be modified.
Any modification may render the product unsafe and will invalidate any Safety/Approval marks.
Philip Payne will not accept any responsibility for any modified products or for any damage caused as a result of their modification.
Monthly and Annual Tests
Monthly and Annual tests should be carried out in accordance with BS EN 50172:2004, 7.2.
Testing can be carried out by using a sub circuit isolator or by switching off the lighting circuit at the circuit breaker (not for AutoTest or DALI versions).
Battery pack shall be replaced if the specified 3 hour duration is not met.
For replacement battery pack contact Philip Payne Ltd.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Cleaning Instructions
REAR CABLE
ENTRY
SURFACE
CABLE ENTRY
OPTION
1 2

Surface Ceiling IP20 Class 1 SPRITE 870 Series
Emergency Downlighter
Dimensions
Connections
LN
DALIDALI
DALI
LN
SPRT870DA
110-240V AC 50/60 Hz
176-280V DC
DALI
SPRT870LA
198-264V AC 50/60 Hz
176-264V DC
Maximum luminaires on a
Type B, 10A circuit breaker
30 luminaires
30 luminaires
Supply voltageDownlighter features Part No.
Do not stare at operating lamp.
It may be harmful to the eyes.
160
160
47
15
35.9
12
35
53
71
148
45
62
80
98
115
Ø20 KNOCKOUT (THIS SIDE ONLY)
Ø5 FIXING HOLES Ø20 CABLE ENTRY
Basic insulation between L/N and
DALI/DALI terminals.

Important-Safety
Before carrying out any servicing on this luminaire, ensure that the mains supply is fully isolated.
Disconnect luminaire before insulation testing of the installation.
Installation Method
Philip Payne Ltd
A SUBSIDIARY OF F.W. THORPE PLC
Thornhill Road, Solihull, B91 2HB, England.
Tel: [phone]
Fax: [phone]
e-mail: [email protected]k
Website: http://www.philippayne.co.uk
Philip Payne Ltd registered in England No. 1361523 ISO9001
FM55077 21LFT065_2
Operation and Maintenance
Continual operation at mains voltages in excess of the rated voltage will reduce LED and expected gear life.
This luminaire uses plastic components in its construction and when installed in environments containing chemicals, degradation may occur.
Please contact our Technical Department for advice.
Modifications
Philip Payne products should not be modified.
Any modification may render the product unsafe and will invalidate any Safety/Approval marks.
Philip Payne will not accept any responsibility for any modified products or for any damage caused as a result of their modification.
Monthly and Annual Tests
Monthly and Annual tests should be carried out in accordance with BS EN 50172:2004, 7.2.
Testing can be carried out by using a sub circuit isolator or by switching off the lighting circuit at the circuit breaker (not for AutoTest or DALI versions).
Battery pack shall be replaced if the specified 3 hour duration is not met.
For replacement battery pack contact Philip Payne Ltd.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Cleaning Instructions
1 2
REAR CABLE
ENTRY
SURFACE
CABLE ENTRY
OPTION

Surface Ceiling IP6X Class 1 SPRITE 870 Series
Emergency Downlighter
Dimensions
Connections
L
NM3
AutoTest DALI
DALI
250 62
160
238 FIXING CENTRES
129 FIXING CENTRES
Ø4.2FIXING HOLES
DALIDALI
N L N USL DALIDALI
N
USL N
SPRP870DA
SPRP870LN
220-240V AC 50/60 Hz
NM3
110-240V AC 50/60 Hz
176-280V DC
DALI
SPRP870LA
198-264V AC 50/60 Hz
176-264V DC
SPRP870YS
220-240V AC 50/60 Hz
NM3 AutoTest
SPRP870DS
220-240V AC 50/60 Hz
DALI
NM3
Maximum luminaires on a
Type B, 10A circuit breaker
30 luminaires
30 luminaires
90 luminaires
90 luminaires
90 luminaires
Supply voltageDownlighter features Part No.
Do not stare at operating lamp.
It may be harmful to the eyes.
NOTICE TO CONTRACTOR - PLEASE PASS THIS LEAFLET TO THE END-USER.
Basic insulation
between L/N and
DALI/DALI terminals.

Installation Method
1
BASE ENTRY
OPTION
4 x FIXING
SCREWS
(NOT SUPPLED)
4 x GEAR TRAY
SCREWS
2
DRILL 19mm CABLE ENTRY.
USE GLAND SUPPLIED.
SIDE ENTRY
OPTION

Important-Safety
Before carrying out any servicing on this luminaire, ensure that the mains supply is fully isolated.
Disconnect luminaire before insulation testing of the installation.
Installation Method
Philip Payne Ltd
A SUBSIDIARY OF F.W. THORPE PLC
Thornhill Road, Solihull, B91 2HB, England.
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
Website: http://www.philippayne.co.uk
Philip Payne Ltd registered in England No. 1361523 ISO9001
FM55077 21LFT054_7
Cleaning Instructions
34
6 x LID SCREWS -
TORQUE SETTING -
100Ncm
Operation and Maintenance
Continual operation at mains voltages in excess of the rated voltage will reduce LED and expected gear life.
This luminaire uses plastic components in its construction and when installed in environments containing chemicals, degradation may occur.
Please contact our Technical Department for advice.
Modifications
Philip Payne products should not be modified.
Any modification may render the product unsafe and will invalidate any Safety/Approval marks.
Philip Payne will not accept any responsibility for any modified products or for any damage caused as a result of their modification.
Monthly and Annual Tests
Monthly and Annual tests should be carried out in accordance with BS EN 50172:2004, 7.2.
Testing can be carried out by using a sub circuit isolator or by switching off the lighting circuit at the circuit breaker (not for AutoTest or DALI versions).
Battery pack shall be replaced if the specified 3 hour duration is not met.
For replacement battery pack contact Philip Payne Ltd.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.