Philips HF3485/01 User manual

HF3485

1

2 3 4 5
6 7 8 9
10 11 12 13
14 15 16 17
18 19 20 21

HF3485
ENGLISH 6
DANSK 18
DEUTSCH 30
 43
ESPAÑOL 57
SUOMI 70
FRANÇAIS 81
ITALIANO 94
NEDERLANDS 106
NORSK 119
PORTUGUÊS 131
SVENSKA 144
TÜRKÇE 156
Table of contents

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.com/welcome.
The Philips Wake-up Light helps you wake up more pleasantly.The light intensity of the lamp
gradually increases to the set level in the set sunrise simulation time (the default time is 30 minutes).
The light gently prepares your body for waking up at the set time.To make waking up an even more
pleasant experience, you can use natural wake-up sounds, the FM radio or even downloaded sounds
or your own music from a USB stick.
The effects of theWake-up Light
The Philips Wake-up Light gently prepares your body for waking up during the last 20 to 40 minutes
of sleep, depending on the sunrise simulation time you set. In the early morning hours our eyes are
more sensitive to light than when we are awake. During that period the relatively low light levels of
a simulated natural sunrise prepare our body for waking up and getting alert. People who use the
Wake-up Light wake up more easily, have a better overall mood in the morning and feel more
energetic. Because the sensitivity to light differs per person, you can set the light intensity of your
Wake-up Light to a level that matches your light sensitivity for an optimal start of the day.
For more information about the Wake-up Light, see www.philips.com.
General description (Fig. 1)
A Top cover with vents
B Lamp housing
C Mains cord
D Antenna
E Display
1 Clock time/alarm time
2 Light intensity symbol
3 Sunrise simulation time symbol
4 Radio symbol
5 ‘Bird’ sound symbol
6 ’Yoga’ sound symbol
7 ’Cowbell’ sound symbol
8 ’Forest’ sound symbol
9 ‘USB stick’ symbol
10 Radio frequency symbol
11 Volume level symbol
12 Display brightness symbol
13 Sunset simulation symbol
14 Alarm sound symbol
15 Alarm 2 symbol
16 Alarm 1 symbol
17 Clock time symbol
F Menu ‘-’ button
G MENU button
H SELECT button (also FM presets selection)
I Menu ‘+’ button
J Control lever with ‘alarm off’,‘alarm 1’ and ‘alarm 2’ positions
K USB socket
L Buttons on the side of the appliance
1 Light intensity increase button
2 Lamp on/off button
3 Light intensity decrease button
ENGLISH

4 Volume increase button
5 Radio on/off button
6 Volume decrease button
Important
- Read this user manual carefully before you use the appliance and save it for future reference.
- This appliance is double insulated according to Class II (Fig. 2).
Danger
- Water and electricity are a dangerous combination. Do not use this appliance in wet
surroundings (e.g. in the bathroom or near a shower or swimming pool).
- Do not let water run into the appliance or spill water onto the appliance (Fig. 3).
Warning
- Check if the voltage indicated on the appliance corresponds to the local mains voltage before
you connect the appliance.
- Do not place anything on top of or close to the appliance that could cause water or any other
liquid to drip or splash onto the appliance.
- As you can only disconnect the appliance from the mains by removing the mains plug from the
wall socket, always make sure the mains plug is within easy reach when the appliance is
connected to the mains.
- The appliance is suitable for a mains voltage of 230V and a frequency of 50Hz.
- If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by
Philips or similarly qualied persons in order to avoid a hazard.
- Always let the appliance cool down for approx. 15 minutes before you open the top cover to
remove the lamp.The lamp and the metal part of the top cover become hot during use and you
may burn your ngers when you touch them. (Fig. 4)
- This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for
their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- This appliance is for indoor use only (Fig. 5).
Caution
- Do not drop the appliance on the oor, hit it hard or expose it to other heavy shocks.
- Place the appliance on a stable, level and non-slippery surface.
- Do not use the appliance at room temperatures lower than 10°C or higher than 35°C.
- Make sure the vents in the top and in the bottom of the appliance remain open during use.
- Never use the appliance if the lamp housing or top cover is damaged, broken or missing.
- Consult your doctor before you start using the appliance if you have suffered from or are
suffering from serious depression.
- Do not use this appliance as a means to reduce your hours of sleep.The purpose of this
appliance is to help you wake up more easily. It does not diminish your need for sleep.
- The appliance has no on/off switch.To disconnect the appliance from the mains, remove the
plug from the wall socket.
- This appliance is only intended for household use, including similar use for instance in hotels.
General
- This appliance allows you to choose the light intensity level you want to wake up to (see section
‘Setting the light intensity’ in chapter ‘Using the appliance’).
- If you often wake up too early or with a headache, reduce the light intensity level and/or the
sunrise simulation time.
ENGLISH 7

- If you share a bedroom with someone else, this person may unintentionally wake up from the
light of the appliance, even though this person is further removed from the appliance.This
phenomenon is the result of differences in light sensitivity between people.
- The power consumption of the appliance is lowest if the radio, the USB playback function and
the lamp are switched off.

This Philips appliance complies with all standards regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.
Preparing for use
Setting the clock
1 Put the plug in the wall socket.
,The hour indication on the display starts ashing to indicate that you have to set the clock
time (Fig. 6).
2 Press the menu - or + button to select the hour.
3 Press the SELECT button to conrm.
,The minute indication starts ashing (Fig. 7).
4 Press the menu - or + button to set the minutes.
5 Press the SELECT button to conrm.
,The appliance leaves the menu and the display shows the set clock time.
The appliance is now ready for use.
Note: The method described above only applies when you plug in the appliance for the rst time, when
there has been a power failure or when the mains plug has been removed from the wall socket for more
than 15 minutes. In these cases, the hour indication ashes to indicate that you have to set the clock
time. In all other cases, you have to use the menu to set the clock time (see section ‘Menu functions’ in
chapter ‘Using the appliance’).
Using the appliance
Menu functions
Below you nd a description of all functions that can be set in the menu. These functions appear in
the menu in the following order:
- Clock time
- Alarm time 1
- Alarm time 2
- Alarm sound
- Sunset simulation
- Display brightness
You can set the menu functions in the following way:
1 Press the MENU button to enter the menu (Fig. 8).
Note: If you do not press any button within 30 seconds, the appliance exits the menu and the display
shows the clock time again.
2 Press the menu - or + button to select a function. (Fig. 9)
3 Press the SELECT button to enter this function (Fig. 10).
4 Press the menu - or + button to change a setting. (Fig. 9)
ENGLISH8

5 Press the SELECT button to conrm (Fig. 10).
Setting the alarm
Setting the alarm time
When you set the alarm, you set an alarm time and light intensity and you choose the type of sound
you want to wake up to. The alarm is set when the alarm symbol is visible on the display.The light
intensity slowly increases to the selected level during the set sunrise simulation time before the set
alarm time.The default sunrise simulation time is 30 minutes.This is the recommended time, but as
the sensitivity to light differs from person to person, it is possible to adjust the sunrise simulation
time to your own preference (see section ‘Setting the sunrise simulation time’ in this chapter).At the
set alarm time (after the sunset simulation time), the alarm sound slowly increases in 90 seconds to
the selected level.
Note: You can set two different alarm times, for example if you want to wake up at a different time in the
weekend than on weekdays.
Note:The volume you set for the alarm is also used as the volume for the radio and music on your
USB stick. To set the alarm volume, press the volume increase or decrease button. If you do not want to
wake up to the lamp or to a sound, select a light intensity or volume level of 0. See sections ‘Using the
appliance as a bedside lamp’ and ‘Setting the volume’ in this chapter.
1 Push the control lever to the middle position if you want to set alarm 1. Push the control
lever to the top position if you want to set alarm 2 (Fig. 11).
,The hour indication of the alarm time starts ashing (Fig. 12).
,To adjust the time, follow steps 2 to 5.
2 Press the menu - or + buttons to set the hour (Fig. 9).
Note: You can only do this when the hour indication ashes. If this is not the case, push the control lever
down and up again to enter the alarm time function. You can also set the alarm time in the menu (see
section ‘Menu functions’ in this chapter).
3 Press the SELECT button to conrm (Fig. 10).
,The minute indication of the alarm time starts ashing (Fig. 13).
4 Press the menu - or + buttons to set the minutes. (Fig. 9)
5 Press the SELECT button to conrm or wait for a few seconds (Fig. 10).
,The appliance leaves the menu and the display shows the clock time.
The alarm time is now set.
Setting the light intensity
You can set the light intensity you prefer for the simulated sunrise that takes place before the alarm
goes off.
Note: The light intensity you set is used for the alarm function as well as for the lamp function (see
section ‘Using the appliance as a bedside lamp’ below).
1 Press the lamp on/off button. (Fig. 14)
Note: It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.
Note: You can also set the light intensity when the lamp is out, but switching on the lamp makes it easier
to determine the preferred light intensity.
2 Press the light intensity increase and decrease buttons to select a light intensity (Fig. 15).
You can choose a light intensity between 1 and 20.
If you do not want the lamp to go on gradually as a simulated sunrise before the alarm goes off, set
the light intensity to 0.
ENGLISH 9

Tip: When you use the appliance for the rst time, set the light intensity to 20. The moment you wake up,
check which light intensity level the appliance has reached by briey pressing the light intensity increase
or decrease button. When you do this, the current alarm light intensity level appears on the display. Set
the alarm light intensity to this level for the next day.
3 To switch off the lamp, press the lamp on/off button again.
Setting the alarm sound
Note: You can adjust the volume level of the alarm sound to your preference (see section ‘Setting the
volume’ in this chapter). If you do not want to wake up to an alarm sound, set the volume level to 0.
1 Follow the instructions in section ‘Menu functions’ above and select the alarm sound function.
2 Press the SELECT button to conrm.
3 Press the menu - or + buttons to select the desired alarm sound (see below).
,The display shows the symbol of the selected alarm sound.
4 Press the SELECT button to conrm.
You can choose one of the following sounds:
- Radio (see also section ‘Using the radio as alarm sound’ below’) (Fig. 16)
- ’Bird’ sound (Fig. 17)
- ’Yoga’ sound (Fig. 18)
- ’Cowbell’ sound (Fig. 19)
- ’Forest’ sound (Fig. 20)
- Downloaded wake-up sounds or your own music from a USB stick (see also section
‘Using music on a USB stick as alarm sound’ below). (Fig. 21)
Tip:You can download more wake-up sounds at www.philips.com.
Using the radio as alarm sound
1 Follow instructions 1-4 in section ‘Setting the alarm sound’ to select the radio as
alarm sound.
,The display shows P1, which is preset radio station 1 (Fig. 22).
If you want to select another preset radio station, press the menu - or + button (see section ‘Using
the radio/playing music from a USB stick’). If you want to change the frequency of the preset radio
stations, see section ‘Using the radio/playing music from a USB stick’ in this chapter)
2 Press the SELECT button to conrm.
,The selected preset radio station is now set as the alarm sound.
Using music on a USB stick as alarm sound
Note: You can only use music on a USB stick if it is in MP3 or WMA format. You can check this on your
computer. The extension of the les should be .mp3 or .wma.
Refer to chapter ‘USB specications’ for more USB information.
1 Insert the USB stick in the USB socket of the appliance.
2 Follow instructions 1-4 in section ‘Menu functions’ above to select music from a USB stick as
alarm sound.
,The display shows 0001 to indicate the rst song on the USB stick. (Fig. 23)
To select another song, press the menu - and + buttons.
3 Press the SELECT button to conrm.
,The selected song is now set as the alarm sound.
ENGLISH10

Setting the sunrise simulation time
The sunrise simulation time is the time in which the light intensity of the lamp gradually increases to
the set level before the alarm sound is played.The default sunrise simulation time is 30 minutes,
because this is the optimum time for your body to prepare for waking up.As the sensitivity to light
differs from person to person, it is possible to adjust the sunrise simulation to your own preference.
You can reduce the sunrise simulation time to 20 or 25 minutes or increase it to 40 minutes.
1 Simultanuously press and hold the light intensity increase and decrease buttons for
3 seconds (Fig. 24).
,The sunrise simulation symbol and the default sunrise simulation time of 30 minutes appears
on the display. (Fig. 25)
2 Press the menu - or + button to increase or decrease the sunrise simulation time. (Fig. 9)
3 Press the SELECT button to conrm (Fig. 10).
Snoozing
1 Tap on the surface of the Wake-Up light with the inside of your hand to snooze the appliance
(some force needs to be applied to prevent accidental snoozing) (Fig. 26).
,The lamp continues to be on at the selected intensity level, but the alarm sound stops. After
9 minutes, the alarm sound is automatically played again.
Note: The 9-minute snooze time is xed. This time cannot be adjusted.
Switching the alarm function off and on
1 To switch off the alarm function when the alarm goes off, push down the control lever to the
bottom position (Fig. 27).
Note:The lamp stays on to light your room.You can switch off the lamp by pressing the lamp on/
off button.
Note: If you forget to switch off the alarm, the alarm (sound and/or light) automatically switches off after
90 minutes.
2 If you want the alarm to go off at one of the set alarm times the next day, set the control
lever to alarm 1 or alarm 2 again.
Alarm demonstration
If you want to get a quick demonstration (60 seconds) of the gradually increasing light intensity and
sound level, activate the test function of the appliance.
1 Simultanuously press and hold the menu - or + buttons until the word TEST appears on the
display (Fig. 28).
2 Simultanuously press the menu - or + buttons again to stop the demonstration.
Note:The appliance continues to run the alarm demonstration until you press the menu + and - button
again.The test automatically stops after 9 hours.
Using the radio/playing music from a USB stick
Switching on the radio
1 To switch on the radio, press the radio on/off button (Fig. 29).
,The radio starts to play.
Note: The radio function has 3 preset stations. To select one of the preset stations, press the SELECT
button below the display.
2 To select the desired radio frequency, press the menu - or + button. (Fig. 30)
ENGLISH 11

Tip: To scan radio frequencies automatically, press and hold the menu - or + button for approx. 2 seconds.
Tip: To make sure you get a good radio signal, fully unwind the antenna and move it around until you
have found a position at which reception is best.
3 To switch off the radio, press the radio on/off button again.
Changing the preset radio stations
The radio of the Wake-Up light has 3 preset radio stations.If you want to set different radio stations
as the preset stations, follow the steps below.
1 Press the radio on/off button to switch on the radio. (Fig. 31)
,The display shows P1, which is preset station 1 (Fig. 22).
Note: Press the SELECT button one or more times if you want to select another preset station.
2 To scan radio frequencies in order to change the preset station, press the menu - or +
button (Fig. 30).
,The appliance automatically stores the selected radio frequency.
Playing music from a USB stick
Note: You can only use music on a USB stick if it is in MP3 or WMA format. The appliance does not play
any other format.You can check this on your computer. The extension of the les should be .mp3 or
.wma. For more information, see chapter ‘USB specications’.
1 To play music from a USB stick, press the radio on/off button twice. (Fig. 31)
,If there is a USB stick in the USB socket, the appliance automatically starts scanning the
number of MP3 or WMA les on the USB stick. This may take a few minutes. Then the
number of songs is shown on the display and the appliance starts playing the rst song on the
USB stick.
,If the appliance detects that the les on the USB stick are not in MP3 or WMA format, the
display shows ‘ERR’.
2 To select the desired song le, press the menu - or + button. (Fig. 30)
If you hold down the menu - or + button, the song selection function skips through the songs faster.
3 To stop playing music from the USB stick, press the radio on/off button again.
Note: Put your music les in the root folder of the USB stick to ensure faster scanning.
Note: The songs are ordered based on the date that the music was put on the USB stick. If you want the
songs to be played in a specic order, put them in this order on your computer rst and then copy them
to your USB stick.
Setting the volume
1 To set the volume for the radio or music from a USB stick, press the volume increase or
decrease button. (Fig. 32)
You can choose a volume level between 1 and 20.
Note:The volume level you have selected is automatically set as the volume level for the alarm as well.
Sunset simulation
You can use the sunset simulation when you want the light and/or the sound of the Wake-up Light
to stay on and dim gradually during a set period of time (15 minutes to 1.5 hours) before you go to
sleep.The lamp and/or sound switch off automatically after the set time.
Note:The light intensity you set for the start of the sunset simulation is also used as the light intensity for
the sunrise simulation
ENGLISH12

1 Switch on the lamp and/or the radio or music from a USB stick. See sections ‘Using the
appliance as a bedside lamp’ and/or ‘Using the radio/playing music from a USB stick’ in
this chapter.
2 Follow the steps in section ‘Menu functions’ in this chapter to select the sunset simulation
function and to set the sunset simulation time.
,You can choose a time from 15 to 90 minutes (15, 30, 60 or 90).
Note: After the set time, no matter whether only the light and/or the radio are on, the sunset simulation
switches off both light and sound.
Tip:You can also press the light on/off button for 3 seconds to activate the sunset simulation
function (Fig. 33).
Using the appliance as a bedside lamp
You can use the appliance as a bedside lamp.
1 To switch on the lamp, press the lamp on/off button. (Fig. 14)
Note: It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.
2 Press the light intensity increase and decrease buttons to select a light intensity (Fig. 15).
You can choose a light intensity between 1 and 20.
Note:The light intensity you have selected is automatically set as the light intensity level for the alarm
as well.
3 To switch off the lamp, press the lamp on/off button again.
Setting the display brightness
1 Follow the steps in section ‘Menu functions’ in this chapter to select the display brightness
function and to set the desired display brightness. (Fig. 34)
,You can select a display brightness between 1 and 4.
Tip: If you set the display brightness to level 1, the appliance consumes the least power.
Note: The display brightness automatically increases to maximum level when setting the appliance to
allow the user optimal visibility. When the user has nished setting the appliance and leaves the menu,
the display brightness automatically returns to the set level.
Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone
to clean the appliance.
Regularly remove dust from the outside of the appliance with a dry cloth.
1 Unplug the appliance before you clean it.
2 Clean the outside of the appliance with a dry cloth.
Do not let water run into the appliance or spill water onto the appliance (Fig. 3).
Replacement
Except for the lamp, the appliance does not contain any serviceable parts.
The lamp has to be replaced when it stops burning or when the light output decreases (also see
chapter ‘Important’).You must replace the lamp with a Philips Halogen lamp, 100W, 12V, GY6.35.
Only this lamp provides the correct light intensity.
Note: This appliance has been designed to be used with self-shielded lamps only (Fig. 35).
ENGLISH 13

For more information, visit our website www.philips.com.
Replacing the lamp
1 Unplug the appliance before you replace the lamp.
2 If the lamp is still hot, let it cool down for approx. 15 minutes.
3 To unlock the top cover, press it and turn it anticlockwise until the O symbol on the top
cover is aligned with the 1symbol on the lamp housing. (Fig. 36)
4 Remove the top cover. (Fig. 37)
5 Remove the old lamp from the lamp holder (Fig. 38).
6 Insert the pins of the new lamp into the lamp holder. (Fig. 39)
Do not touch the lamp with your ngers. Use a cloth or paper towel when you place
the lamp (Fig. 40).
7 Place the top cover back onto the appliance.
8 Lock the top cover by turning it clockwise until the 1 symbol on the top cover and the 1
symbol on the lamp housing are aligned. (Fig. 41)
Environment
- Do not throw away the appliance with the normal household waste at the end of its life, but
hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the
environment (Fig. 42).
Guarantee and service
If you need service or information or if you have a problem, please visit the Philips website at
www.philips.com or contact the Philips Consumer Care Centre in your country (you nd its phone
number in the worldwide guarantee leaet). If there is no Consumer Care Centre in your country,
go to your local Philips dealer.
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If
you are unable to solve the problem with the information below, contact the Consumer Care
Centre in your country.
Problem Solution
The appliance does not
work at all. Perhaps the plug is not inserted properly in the wall socket. Put the plug properly in the wall socket.
Perhaps there is a power failure. Check if the power supply works by
connecting another appliance.
The appliance functions
properly, but the lamp
does not work
anymore.
Perhaps the lamp has reached the end of its life.The life depends on
how you use the appliance. In case of heavy use, the lamp may not last
as long as you expect. If the lamp breaks down, you can order a new
one or buy it at your local retailer. Contact the Philips Consumer Care
Centre in your country.
The appliance becomes
hot during use. This is normal, as the appliance is heated up by the light of the lamp and the electronics.Always let the appliance cool down before you replace
the lamp.
ENGLISH14

Problem Solution
The appliance does not
respond when I try to
set different functions.
Remove the plug from the wall socket and wait 20 minutes before you
reinsert it.When you reinsert the plug, the appliance goes back to the
factory settings and you have to set all functions again.
The lamp does not go
on when the alarm
goes off.
Perhaps you set a light intensity level that is too low. Increase the light
intensity level.
Perhaps you switched off the alarm function by setting the control lever
to the bottom position.To switch on the alarm function, set the control
lever to the middle position (alarm 1) or top position (alarm 2),
depending on the time at which you want to wake up.
Perhaps the appliance is defective. Contact the Philips Consumer Care
Centre in your country.
The lamp does not go
on right away when I
switch it on.
It takes approx. 1 second for the lamp to go on.This is normal, the lamp
needs to heat up.
I do not hear the alarm
sound when the alarm
goes off.
Perhaps you set a sound level that is too low.To set a higher sound level,
see chapter ‘Using the appliance’, section ‘Setting the volume’.
Perhaps you switched off the alarm function by setting the control lever
to the bottom position.
If you selected the radio as the alarm sound, the radio may be defective.
Switch on the radio after you switch off the alarm to check if the radio
works. If it does not work, contact the Philips Consumer Care Centre in
your country.
If you selected a downloaded wake-up sound or music on a USB stick
as the alarm sound, it is possible that the sounds or songs do not have
the correct format. This appliance only supports .mp3 and .wma les. If
the sound or music on the USB stick cannot be played, the appliance
automatically sets the bird sound as alarm sound to ensure
that you wake up at the set alarm time anyway.
The radio does not
work. The radio may be defective. Contact the Philips Consumer Care Centre in your country.
Perhaps you set the volume too low. Increase the volume level.
The radio produces a
crackling sound. Perhaps the broadcast signal is weak.Adjust the frequency (see chapter ‘Using the appliance’ section ‘Using the radio/playing music from a USB
stick’) and/or change the position of the antenna by moving it around.
Make sure you have unwound the antenna completely.
The alarm went off
yesterday, but it did not
go off today.
Perhaps you switched off the alarm function by setting the control
lever to the bottom position.
Perhaps you set a volume level and/or light intensity level that is too
low. Set a higher volume level and/or light intensity level.
ENGLISH 15

Problem Solution
Perhaps there was a power failure that lasted more than approximately
15 minutes. In this case, the appliance goes back to factory settings.You
need to set all functions again.
I wanted to snooze, but
the alarm did not go
off again after
9 minutes.
You probably pushed down the control lever to bottom position.This
switches off the alarm function altogether. If you want to snooze, you
have to tap on the appliance.
Perhaps you set the volume level to 0.
The light wakes me too
early. Perhaps the light intensity level you have set is not appropriate for you. Try a lower light intensity level if you wake up too early. If light intensity
1 is not low enough, move the appliance further away from the bed.
The light wakes me too
late Perhaps the appliance is positioned at a lower level than your head. Make sure the appliance is located at a height at which the light is not
blocked by your bed, duvet or pillow. Also make sure the appliance is
not placed too far away.
The lamp ashes. Perhaps the appliance is not suitable for the voltage to which it is
connected. Make sure that the voltage indicated on the appliance
corresponds to the local mains voltage.
The appliance does not
recognise the USB stick. Perhaps the USB stick is not inserted into the USB socket properly. Make sure you push the USB stick far enough into the USB socket.
An error message
appears on the display
when I insert the USB
stick into the USB
socket.
Perhaps the music on the USB stick does not have the right format.
Make sure that the song is an MP3 or WMA le. You can check this on
your computer. The extension of the les should be .mp3 or .wma. See
chapter ‘USB specications’ for more information.
I have programmed the
appliance to wake me
up with music on a
USB stick, but instead I
hear a bird sound.
Perhaps you have removed the USB stick from the appliance or it is not
inserted into the USB socket properly. If the appliance does not detect
a USB stick, it automatically sets the bird sound as alarm sound to
ensure that you wake up at the set alarm time anyway.To use music on
a USB stick as alarm sound, the USB has to be in the USB socket
permanently.

Compatible USB devices
- USB ash memory (USB2.0 or USB1.1)
- USB ash players (USB2.0 or USB1.1)
- Memory cards (requires an additional card reader to work with this audio system)
Note: If your USB device a boot function, please wait until it has nished booting and is ready for use
before you connect it to the USB port of the appliance.
Supported formats
- USB or memory le format (FAT12, FAT16, FAT32 (sector size: 512 bytes)
- MP3 bit rate (data rate): 32-320 Kbps and variable bit rate
- WMA v7, v8 or v9
- Directory nesting up to a maximum of 8 levels
ENGLISH16

- Number of albums/folders: maximum 99
- Number of tracks/titles: maximum 999
- File name in Unicode UTF8 (maximum length: 128 bytes)
Unsupported formats:
- Empty albums: an empty album is an album that does not contain MP3/WMA les and is
not shown on the display.
- Unsupported le formats are skipped. For example Word documents (.doc) or MP3 les with
extension .dlf are ignored and not played.
- AAC, WAV and PCM audio les
- DRM protected les are not supported.
- WMA les in Lossless format
- Hidden les
ENGLISH 17

18
Introduktion
Tillykke med dit køb og velkommen til Philips! For at få fuldt udbytte af den support, Philips tilbyder,
skal du registrere dit produkt på www.philips.com/welcome.
Med Philips Wake-up Light får du en mere behagelig opvågning. Lampens lysintensitet stiger gradvist
til det indstillede niveau for simulation af solopgang i løbet af det forudindstillede tidsrum
(standardtiden er 30 minutter). Lyset forbereder nænsomt din krop på at vågne på det indstillede
tidspunkt. Du kan gøre opvågningen endnu mere behagelig ved at bruge naturlige vækkelyde, FM-
radio eller for den sags skyld downloadede lyde eller din egen musik fra en USB-nøgle.
Virkningerne ved Wake-up Light
Philips Wake-up Light forbereder nænsomt din krop på at vågne i løbet af de sidste 20 til
40 minutters søvn, afhængigt af den tid til simulation af solopgang du indstiller. I de tidlige
morgentimer er øjnene mere følsomme over for skarpt lys, end når vi er vågne. I den periode
forbereder det forholdsvist lave lysniveau fra simuleret solopgang kroppen på at vågne og komme i
gang. Personer, der bruger Wake-up Light, vågner nemmere op, er generelt i bedre humør om
morgenen og har mere energi. Da lysfølsomheden er forskellig fra person til person, kan du indstille
lysintensiteten på Wake-up Light til et niveau, der passer til din egen lysfølsomhed, så du får en
optimal start på dagen.
Du nder ere oplysninger om Wake-up Light på www.philips.com.

A Topdæksel med ventilationshuller
B Lampekabinet
C Netledning
D Antenne
E Display
1 Klokkeslæt/vækketidspunkt
2 Symbol for lysintensitet
3 Tidssymbol for simulation af solopgang
4 Radiosymbol
5 Symbol for “fugle”-lyd
6 Symbol for “yoga”-lyd
7 Symbol for “koklokke”-lyd
8 Symbol for “skov”-lyd
9 Symbol for “USB-nøgle”
10 Symbol for radiofrekvens
11 Symbol for lydstyrkeniveau
12 Symbol for displaylysstyrke
13 Symbol for simulation af solnedgang
14 Symbol for vækkelyd
15 Symbol for alarm 2
16 Symbol for alarm 1
17 Klokkeslætsymbol
F Menuknappen “-”
G MENU-knap
H VÆLG-knap (også faste FM-stationer)
I Menuknappen “+”
J Aktiveringsknap med positionerne “alarm fra”,“alarm 1” og “alarm 2”
K USB-stik
L Knapper på siden af apparatet
1 Knap til at øge lysintensiteten
2 Tænd/sluk-knap til lampe
DANSK

3 Knap til at mindske lysintensiteten
4 Knap til at øge lydstyrke
5 Tænd/sluk-knap til radio
6 Knap til at sænke lydstyrke
Vigtigt
- Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i brug, og gem den til
eventuelt senere brug.
- Dette apparat er dobbeltisoleret i henhold til Klasse II (g. 2).
Fare
- Vand og elektricitet er en farlig kombination.Anvend aldrig apparatet i våde omgivelser (f.eks. i
badeværelset eller i nærheden af en bruser eller swimmingpool).
- Sørg for, at der ikke trænger vand ind i apparatet, og at der ikke spildes vand på det (g. 3).
Advarsel
- Kontrollér, om den angivne netspænding på apparatet svarer til den lokale netspænding, før du
slutter strøm til apparatet.
- Placer ikke noget ovenpå eller i nærheden af apparatet, der kan få vand eller anden væske til at
dryppe eller stænke på det.
- Da du kun kan afbryde strømtilførslen til apparatet ved at trække stikket ud af stikkontakten, skal
du altid sørge for at at stikket er inden for rækkevidde, når apparatet tilsluttes til stikkontakten.
- Apparatet kan tilsluttes en netspænding på 230 V og en frekvens på 50 Hz.
- Hvis netledningen beskadiges, må den kun udskiftes af Philips, et autoriseret Philips-
serviceværksted eller en tilsvarende kvaliceret fagmand for at undgå enhver risiko.
- Lad altid apparatet køle ned i ca. 15 min, inden du åbner det øverste låg for at fjerne pæren.
Pæren og metaldelen af det øverste låg bliver varme under brug, og du risikerer at brænde
ngrene, når du rører ved dem. (g. 4)
- Dette apparat er ikke beregnet til at blive brugt af personer (herunder børn) med nedsatte
fysiske og mentale evner, nedsat følesans eller manglende erfaring og viden, medmindre de er
blevet vejledt eller instrueret i apparatets anvendelse af en person, der er ansvarlig for
deres sikkerhed.
- Apparatet bør holdes uden for børns rækkevidde for at sikre, at de ikke kan komme til at
lege med det.
- Apparatet må kun benyttes indendørs (g. 5).
Forsigtig
- Undlad at tabe apparatet på gulvet, og udsæt det ikke for kraftige slag eller andre voldsomme
stød.
- Anbring apparatet på et stabilt, vandret og skridsikkert underlag.
- Undlad at anvende apparatet, hvis rumtemperaturen er under 10°C eller højere end 35°C.
- Sørg for, at ventilationshullerne for oven og for neden på apparatet forbliver åbne under brug.
- Brug ikke apparatet, hvis lampens kabinet eller øvre dæksel er beskadiget, knækket eller mangler.
- Kontakt din læge, før du begynder at bruge apparatet, hvis du har lidt af eller lider af
alvorlig depression.
- Brug ikke apparatet som et middel til at reducere dit søvnbehov. Formålet med apparatet er at
lette opvågningen. Det reducerer ikke søvnbehovet.
- Apparatet har ingen on/off (tænd/sluk)-kontakt.Træk stikket ud af stikkontakten for at afbryde
forbindelsen til lysnettet.
- Dette apparat er kun beregnet til husholdningsbrug, herunder lignende brug f.eks. på hoteller.
Generelt
- Apparatet giver dig mulighed for at vælge, hvilket lysintensitetsniveau du ønsker at vågne op til
(se afsnittet “Indstilling af lysintensiteten” i kapitlet “Sådan bruges apparatet”).
DANSK 19

- Hvis du ofte vågner for tidligt eller med hovedpine, skal du reducere lysintensitetsniveauet og/
eller tiden til simulation af solopgang.
- Hvis du deler soveværelse med andre, kan vedkommende blive vækket utilsigtet, selvom han/hun
ligger længere væk fra apparatet. Dette skyldes, at mennesker ikke nødvendigvis har
samme lysfølsomhed.
- Apparatets strømforbrug er lavest, hvis du har slukket for radioen, USB-afspilningsfunktionen
og lampen.
Elektromagnetiske felter (EMF)
Dette Philips-apparat overholder alle standarder for elektromagnetiske felter (EMF).Ved korrekt
anvendelse i overensstemmelse med instruktionerne i denne brugervejledning er apparatet sikkert
at anvende ifølge den videnskabelige viden, der er tilgængelig i dag.
Klargøring
Indstilling af uret
1 Sæt stikket i stikkontakten.
,Timeangivelsen på displayet begynder at blinke for at indikere, at du skal indstille
klokkeslættet (g. 6).
2 Tryk på menuknappen - eller + for at vælge timetal.
3 Tryk på VÆLG-knappen for at fortsætte.
,Minutangivelsen begynder at blinke (g. 7).
4 Tryk på menuknappen + eller - for at indstille minuttallet.
5 Tryk på VÆLG-knappen for at fortsætte.
,Apparatet forlader nu menuen, og displayet viser klokkeslættet.
Apparatet er nu klar til brug.
Bemærk: Den ovenfor beskrevne metode gælder kun, når du tilslutter apparatet for første gang, når der
har været strømsvigt, eller når netstikket har været taget ud af stikkontakten i mere end 15 minutter. I
disse tilfælde blinker timeangivelsen for at indikere, at du skal indstille klokkeslættet. I alle andre tilfælde
skal du bruge menuen til at indstille klokkeslættet (se afsnittet “Menufunktioner” i kapitlet “Sådan
bruges apparatet”).
Sådan bruges apparatet
Menufunktioner
Nedenfor nder du en beskrivelse af alle funktioner, der kan angives i menuen. Disse funktioner vises
i menuen i følgende rækkefølge:
- Klokkeslæt
- Vækketidspunkt 1
- Vækketidspunkt 2
- Vækkelyd
- Simulation af solnedgang
- Skærmlysstyrke
Du kan indstille menufunktionerne på følgende måde:
1 Tryk på MENU-knappen for at åbne menuen (g. 8).
Bemærk: Hvis du ikke trykker på nogen knap inden for 30 sekunder, forlader apparatet menuen, og
displayet viser igen klokkeslættet.
2 Tryk på menuknappen - eller + for at vælge en funktion. (g. 9)
DANSK20