Philips SCF355 User manual

SCF355

1
1
2
3
5 4 8 7 6

SCF355
ENGLISH 6
DANSK 15
ΕΛΛΗΝΙΚΑ 24
ESPAÑOL 34
SUOMI 44
NORSK 52
PORTUGUÊS 61
SVENSKA 71
86

6
General description (Fig. 1)
1 Bottle warmer
2 Light
3 Settings knob
4 Off setting
5 Defrost setting
6 Milk warming setting for contents up to 180ml/6oz
7 Food warming setting
8 Milk warming setting for contents over and including 180ml/6oz
Important
To fully benet from the support that Philips offers,
register your appliance at www.philips.com/
welcome.
Read this user manual carefully before you use the
bottle warmer and save it for future reference.
Danger
- Do not immerse the cord, plug or appliance in
water or other liquid.
Warning
- Only use the appliance indoors.
- Do not let the mains cord hang over the edge of
a table or worktop. Excess cord can be stored in
the base of the bottle warmer.
- Keep the mains cord away from hot surfaces.
- Only connect the appliance to an earthed wall
socket. Always make sure that the plug is inserted
into the wall socket properly.
ENGLISH

- Check if the voltage indicated on the bottom of
the appliance corresponds to the local mains
voltage before you connect the appliance.
- If you need to use an extension cord, make sure it
is an earthed extension cord with a rating of at
least 13 amperes.
- Do not use the appliance if the plug, the mains cord
or the appliance itself is damaged. If the mains cord
is damaged, you must have it replaced by Philips,
a service centre authorised by Philips or similarly
qualied persons in order to avoid a hazard.
- Do not place the appliance on or near a hot gas
or electric cooker, or in a heated oven.
- This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Cleaning and user maintenance
shall not be made by children unless they are
older than 8 years and supervised.Keep the
appliance and its cord out of the reach of children
aged less than 8 years.
- Children shall not play with the appliance.
- Do not spill water on the mains plug.
- Only use the appliance as described in the user
manual to avoid potential injury due to misuse.
ENGLISH 7

- Do not preheat the appliance.
- Always place a fully assembled bottle with cap in
the bottle warmer before you add water.
- Make sure you add water before you switch on
the bottle warmer.
- Hot water can cause serious burns. Be careful
when the bottle warmer contains hot water.
- The accessible surfaces of the appliance may
become hot during use and are subject to residual
heat after use.
- Do not move the appliance when it contains hot
water.
- When the food or milk has reached the required
temperature, remove the bottle or container from
the bottle warmer. If you leave food or milk in the
bottle warmer, the temperature of the food or
milk increases.
- Always check the food temperature before you
feed your child.
Caution
- This appliance is intended to be used in
household and similar applications such as farm
houses, bed and breakfast type environments, staff
kitchen areas in shops, ofces and other working
environments, and by clients in hotels, motels and
other residential type environments.
- Unplug the appliance when it is not in use.
ENGLISH8

- The surface of the heating element is subject to
residual heat after use.
- Let the appliance cool down before you clean it.
- Follow the descaling instructions to avoid
irreparable damage.
- Do not try to open or repair the appliance
yourself. You can contact the Philips Consumer
Care Centre in your country
(see www.philips.com/support).
You can nd the production date code YYWW in
the cord storage compartment in the base of the
bottle warmer.
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic elds.
Using the bottle warmer
With this bottle warmer, you can safely warm all Philips Avent feeding
bottles and milk/baby food in containers and other baby food jars.
Note: Philips Avent breast milk bags and Philips Avent 2oz/60ml bottles
cannot be used in this bottle warmer.
Explanation of settings
- Off setting:The bottle warmer is switched off and the light is off.
On every other setting, the appliance is switched on and the light is
lit (Fig. 2).
- Defrost setting: Defrost a bottle/container of milk/baby food to liquid
state. No warming occurs.
- Milk warming setting for contents up to 180ml/6oz: Select this setting
when you want to warm a bottle of milk with a content up to
180ml/6oz.
ENGLISH 9

- Food warming setting: Select this setting when you want to warm
a container/jar of baby food.
- Milk warming setting for contents over and including 180ml/6oz:
Select this setting when you want to warm a bottle of milk with
a content over and including 180ml/6oz.
Using the bottle warmer to warm milk
1 Put the mains plug in the wall socket (Fig. 3).
2 Place a bottle in the bottle warmer (Fig. 4).
3 Fill the bottle warmer with drinking water up to the level of the
milk in the bottle. In case of large amounts of milk, the maximum
level of water is approximately 1 cm below the top of the bottle
warmer.An accurate water level ensures correct warming
performance (Fig. 5).
4
Select the desired setting. See the warming reference table at the end
of this chapter to check how long the milk needs to be warmed in
the selected setting (Fig. 6).
Note:The speed of warming milk depends on the amount of the milk
warmed and on its initial temperature, i.e. room temperature (20°C) or fridge
temperature (5°C).
5 The orange light goes on when you select a setting.This indicates
that the bottle warmer is on (Fig. 7).
Note:Whilst warming the milk circulates and heats evenly.
6 Check the warming reference table for the time required to warm
the milk. Remove the bottle from the bottle warmer after the time
indicated in the warming reference table has passed (Fig. 8).
Tip: When you nd the milk is not warm enough, you can place the bottle
back into the appliance for a maximum of 30 seconds of extra warming.
This will create a slightly warmer result but without overheating.
Caution: If you leave the bottle in the bottle warmer longer than the
time indicated in the settings table, the milk may become overheated.
Note: If you overheat breast milk, valuable nutrients and vitamins may be lost.
ENGLISH10

7 Always check the temperature before you feed your baby.
Gently shake the bottle or milk storage container and check the
temperature of the milk by sprinkling a few drops on the inside of
your wrist (Fig. 9).
8 Turn the knob back to the ‘off’ position (Fig. 10).
Caution: If you do not turn the knob back to the ‘off’ position,
the water keeps warming.
Using the bottle warmer to warm baby food
1 Follow the same steps as indicated in the previous paragraph.
2 Make sure to stir the baby food during warming as it does not
circulate automatically. Be careful not to burn your ngers when
holding the container/jar while stirring. (Fig. 11)
After warming test the baby food with a spoon to ensure it is not too hot.
If the baby food is not warm enough, put the container back into the bottle
warmer and warm the baby food until it has the desired temperature.
Note: Due to the high variety of baby food consistencies, it is strongly
recommended to continuously stir and check while you are warming the baby
food for an optimal result.
Defrost setting
At this setting, your frozen milk can be defrosted till liquid state.
Check the warming reference table for the expected defrost timings,
as indication one small and one larger milk volume are included in the
table. When your milk is defrosted, choose one of the warming settings.
Consider the start temperature of your milk around room temperature
for the warming timings as rough guideline.
Note: Due to the high variety of baby food consistencies, it is strongly
recommended to continuously stir and check while you are defrosting the
baby food for an optimal result.
ENGLISH 11

Warming reference table
Start temperature
of milk
Milk content 20°C 5°C Frozen
60-90ml/2-3oz 3 min 4.5 min 1-1.5 hrs
90-110ml/3-4oz 3 min 5.5 min
125-150ml/4-5oz 3 min 3.5 min
180-210ml/6-7oz 4 min 5.5 min 1.5-2.5 hrs
240-260ml/8-9oz 4.5 min 7 min
290-330ml/10-11oz 5 min 7.5 min
Note:The indicated warming times are based on Philips Avent Classic and
Natural PP bottle ranges. Be aware that warming timings of Philips Avent
standard bottles and glass bottles deviate from these indications.
The characteristics of bottles such as material or thickness may also impact
the warming times, therefore it may take less time to warm a larger volume
of milk.
Note:The indicated defrosting times are based on Philips Avent food
containers.
Note: Due to the high variety of baby food consistencies, it is not possible to
indicate warming timings for baby food.
Note:The food or milk may feel cool to you, but for a newborn baby its
temperature is very pleasant.
ENGLISH12

Cleaning and descaling
Cleaning
1 After each use, unplug the bottle warmer and let it cool down
(Fig. 12).
2 Remove the water from the bottle warmer for hygienic reasons
(Fig. 13).
3 Wipe the outside and inside of the bottle warmer with a moist
cloth (Fig. 14).
Do not use abrasive, anti-bacterial cleaning agents, chemical solvents or
sharp tools to clean the bottle warmer.
Note: If you used the bottle warmer to warm containers with baby food,
make sure that no spilled baby food remains on the bottom of the bottle
warmer.
Descaling
It is recommended to descale the bottle warmer every four weeks to
ensure it continues to work efciently.
1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold water to
descale the bottle warmer. Switch on the bottle warmer, select the
milk warming setting for contents under 180ml/6oz and let the
appliance operate for 10 minutes. Leave the solution in the bottle
warmer until all scale has dissolved (Fig. 15).
Note:You can also use citric acid based descalers.
Note: Do not use other types of descalers.
2 Unplug the bottle warmer before you empty it (Fig. 12).
3 Empty the bottle warmer and rinse its inside thoroughly.
If you still see traces of scale after rinsing, repeat the descaling
procedure (Fig. 13).
ENGLISH 13

Recycling
- This symbol on a product means that the product is covered by
European Directive 2012/19/EU. Inform yourself about the local
separate collection system for electrical and electronic products.
Follow local rules and never dispose of the product with normal
household waste. Correct disposal of old products helps prevent
negative consequences for the environment and human health.
(Fig. 16)
Guarantee and support
If you need information or support, please visit www.philips.com/
support or read the separate worldwide guarantee leaet.
ENGLISH14

DANSK 15
Generel beskrivelse (g. 1)
1 Flaskevarmer
2 Lys
3 Indstillingsknap
4 Off-indstilling
5 Optøningsindstilling
6 Indstilling for opvarmning af mælk for asker op til 180 ml/6 oz
7 Indstilling for opvarmning af mad
8 Indstilling for opvarmning af mælk for asker på 180 ml/6 oz og
derover
Vigtigt
For at få fuldt udbytte af den vejledning, som
Philips tilbyder, skal du registrere dit apparat på
www.philips.com/welcome.
Læs denne brugervejledning omhyggeligt igennem,
inden askevarmeren tages i brug, og opbevar den til
eventuel senere brug.
Fare
- Ledning, stik eller apparat må aldrig kommes ned
i vand eller andre væsker.
Advarsel
- Apparatet må kun anvendes indendørs.
- Lad aldrig ledningen hænge ud over kanten af et
bord eller køkkenbord. Overskydende ledning kan
opbevares i bunden af askevarmeren.
- Sørg for, at netledningen ikke kommer i berøring
med varme ader.

- Apparatet må kun sluttes til en stikkontakt med
jordforbindelse. Kontrollér altid, at stikket er sat
korrekt i stikkontakten.
- Kontrollér, om spændingsangivelsen i bunden af
apparatet svarer til den lokale netspænding,
før du slutter strøm til apparatet.
- Hvis du skal bruge en forlængerledning, skal du
sørge for, at det er en forlængerledning med
jordforbindelse og på mindst 13 ampere.
- Brug ikke apparatet, hvis stik, netledning, eller selve
apparatet er beskadiget. Hvis netledningen
beskadiges, må den kun udskiftes af Philips,
et autoriseret Philips-serviceværksted eller en
tilsvarende kvaliceret fagmand for at undgå
enhver risiko.
- Placér ikke apparatet på eller i nærheden af et
varmt gasblus eller en elkoger eller i en varm ovn.
- Dette apparat kan bruges af børn fra 8 år og
opefter og personer med nedsatte fysiske,
sensoriske eller mentale evner eller manglende
erfaring og viden, hvis de er blevet instrueret
i sikker brug af apparatet og forstår de
medfølgende risici. Rengøring og
brugervedligeholdelse må ikke foretages af børn,
medmindre de er over 8 år og er under opsyn.
Hold apparatet og dets ledning uden for
rækkevidden af børn under 8 år.
- Lad ikke børn lege med apparatet.
DANSK16

- Undgå at spilde vand på stikket.
- Brug kun apparatet som beskrevet i
brugervejledningen for derved at undgå mulig
personskade på grund af forkert brug.
- Undlad at forvarme apparatet.
- Placer altid en fuldt samlet aske med låg
i askevarmeren, før du tilføjer vand.
- Sørg for at tilføje vand, før du tænder for
askevarmeren.
- Varmt vand kan forårsage alvorlige brandsår.
Pas på, når der er varmt vand i askevarmeren.
- Ydersiden kan blive varm under brug og udsættes
for spildvarme efter brug.
- Flyt ikke apparatet, hvis det indeholder varmt vand.
- Når maden eller mælken har nået det ønskede
temperatur, skal du fjerne asken eller beholderen
fra askevarmeren. Hvis du efterlader mad eller
mælk i askevarmeren, forøges madens eller
mælkens temperatur.
- Kontroller altid madens temperatur, før du
begynder at made dit barn.
Forsigtig
- Dette apparat er beregnet til brug i hjemmet
og andre lignende steder; såsom gårde, bed and
breakfast-steder, personalekøkkener i butikker,
på kontorer og i andre arbejdspladser. Det kan
også benyttes af gæster på hoteller og moteller.
- Tag stikket ud af apparatet, når det ikke er i brug.
DANSK 17

- Varmelegemets overade kan være varm efter brug.
- Lad apparatet køle af, før du stiller den væk.
- Følg afkalkningsinstruktionerne for at undgå
uoprettelig skade.
- Prøv ikke selv at åbne eller reparere apparatet.
Du kan kontakte det lokale Philips Kundecenter
(se www.philips.com/support).
Du kan nde produktionsdatokoden YYWW
i rummet til ledningsopbevaring i bunden af
askevarmeren.
Elektromagnetiske felter (EMF)
Dette Philips-apparat overholder alle branchens gældende standarder og
regler angående eksponering for elektromagnetiske felter.
Brug af askevarmeren
Med denne askevarmer kan du på sikker vis varme alle Philips Avent-
sutteasker og mælk/babymad i beholdere og andre glas med babymad.
Bemærk: Philips Avent-modermælksposer og 60 ml/2 oz Philips Avent-
sutteasker kan ikke bruges i denne askevarmer.
Forklaring af indstillinger
- Off-indstilling: Flaskevarmeren er slukket, og lyset er slukket. Ved alle
andre indstillinger er apparatet tændt, og lyset er tændt (g. 2).
- Optøningsindstilling: Optø en aske/beholder med mælk/babymad til
ydende tilstand. Der foregår ingen opvarmning.
- Indstilling for opvarmning af mælk for asker op til 180 ml/6 oz: Vælg
denne indstilling, hvis du vil varme en aske mælk med et indhold på
op til 180 ml/6 oz.
- Indstilling for opvarmning af mad: Vælg denne indstilling, hvis du vil
varme en beholder/et glas med babymad.
- Indstilling for opvarmning af mælk for asker på 180 ml/6 oz og
derover: Vælg denne indstilling, hvis du vil varme en aske mælk med
et indhold på 180 ml/6 oz og derover.
DANSK18

Opvarmning af mælk ved hjælp af askevarmeren
1 Sæt stikket i en stikkontakt (g. 3).
2 Placer en aske i askevarmeren (g. 4).
3 Fyld askevarmeren med drikkevand op til niveauet for mælken i
asken. I tilfælde af store mængder mælk er maksimummarkeringen
for vand ca. 1 cm under toppen af askevarmeren. En præcis
vandstand sikrer passende opvarmningsevne (g. 5).
4 Vælg den ønskede indstilling. Se referencetabellen til opvarmning
sidst i dette kapitel for at nde ud af, hvor længe mælk skal
opvarmes i den valgte indstilling (g. 6).
Bemærk: Hastigheden for opvarmning af mælk afhænger af mængden af
opvarmet mælk og af den oprindelige temperatur, f.eks. stuetemperatur
(20 °C) eller køleskabstemperatur (5 °C).
5 Det orange lys tændes, når du vælger en indstilling. Dette indikerer,
at askevarmeren er tændt (g. 7).
Bemærk: Under opvarmningen spredes og opvarmes mælken jævnt.
6 Se i referencetabellen til opvarmning, hvor lang tid det tager at
opvarme mælken. Fjern asken fra askevarmeren, når den angivne
tid i referencetabellen til opvarmning er gået (g. 8).
Tip: Hvis du ikke synes, at mælken er varm nok, kan du stille asken tilbage
i apparatet til ekstra opvarmning i højst 30 sekunder. Dette vil give et lidt
varmere resultat, men uden overophedning.
Forsigtig: Hvis du efterlader asken i askevarmeren i længere tid end den
angivne tid i indstillingstabellen, risikerer mælken at blive overophedet.
Bemærk: Hvis du overopheder modermælk, kan der forsvinde værdifulde
næringsstoffer og vitaminer.
7 Kontroller altid temperaturen, før du begynder at made barnet.
Ryst forsigtigt asken eller mælkebeholderen, og kontroller
mælkens temperatur ved at dryppe et par dråber på indersiden af
håndleddet (g. 9).
DANSK 19

8 Drej knappen tilbage til “off” (g. 10).
Forsigtig: Hvis du ikke drejer knappen tilbage til “off”, opvarmes vandet
fortsat.
Opvarming af babymad ved hjælp af askevarmeren
1 Følg de samme trin som angivet i forrige afsnit.
2 Sørg for at røre rundt i babymaden under opvarmning, da det ikke
cirkulerer automatisk. Pas på ikke at brænde ngrene, når du holder
beholderen/glasset under omrøring. (g. 11)
Efter opvarmning skal du teste babymaden med en ske for at sikre, at den
ikke er for varm. Hvis babymaden ikke er varm nok, skal du sætte
beholderen tilbage i askevarmeren og opvarme babymaden, indtil den
har den ønskede temperatur.
Bemærk: På grund af den lange række af babymadkonsistenser anbefales det
på det kraftigste at røre rundt konstant og kontrollere, mens du opvarmer
babymaden, for at opnå et optimalt resultat.
Optøningsindstilling
Ved denne indstilling kan din nedfrossede mælk blive optøet til ydende
tilstand. Se i referencetabellen til opvarmning, hvor lang tid optøningen
forventes at tage, som indikator er en lille og en større mængde mælk
inkluderet i tabellen. Når mælken er optøet, skal du vælge en af
indstillingerne for opvarmning. Brug mælkens starttemperatur, der ca.
er på stuetemperatur, som en grov retningslinje for opvarmningstiderne.
Bemærk: På grund af den lange række af babymadkonsistenser anbefales det
på det kraftigste at røre rundt konstant og kontrollere, mens du tør
babymaden op, for at opnå et optimalt resultat.
DANSK20