Philips AVENT scf356 User manual

User manual
SCF356
Always here to help you
Register your product and get support at
www.philips.com/welcome
Specications are subject to change without notice
© 2016 Koninklijke Philips N.V.
All rights reserved
4213.354.3668.4

1
2345
6789
10 11 12 13
14 15 16 17
18 19 20 21
22 23 24 25
26

SCF356
ENGLISH 6
DANSK 20
ΕΛΛΗΝΙΚΑ 34
ESPAÑOL 49
SUOMI 65
ITALIANO 79
NORSK 95
PORTUGUÊS 109
SVENSKA 125

6
General description (Fig. 1)
1. Baby bottle warmer
2. Progress indicator
3. Settings and on/o knob
4. Defrost setting
5. Milk warming setting 1
6. Milk warming setting 2
7. Milk warming setting 3
8. Baby food warming setting
9. On/o button
Important
To fully benet from the support that Philips
oers, register your appliance at
www.philips.com/welcome.
Read this user manual carefully before you
use the baby bottle warmer and save it for
future reference.
Danger
-Never immerse the appliance in water or
any other liquid, nor rinse it under the tap.
Warning
-Only use the appliance indoors.
-This appliances can be used by persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
ENGLISH

-Cleaning and user maintenance shall not
be made by children.
-This appliance shall not be used by
children. Keep the appliance and its cord
out of reach of children.
-Children shall not play with the appliance.
-Do not immerse the cord, plug or
appliance in water or any other liquid.
-Do not let the mains cord hang over the
edge of a table or worktop. Excess cord
can be stored in the base of the baby
bottle warmer to ensure stability of the
appliance.
-Keep the mains cord away from hot
surfaces.
-Only connect the appliance to an earthed
wall socket. Always make sure that the
plug is inserted into the wall socket
properly.
-Check if the voltage indicated on the
bottom of the appliance corresponds to
the local mains voltage before you
connect the appliance.
-If you need to use an extension cord,
make sure it is an earthed extension cord
with a rating of at least 13 amperes.
ENGLISH 7

-Do not use the appliance if the plug, the
mains cord or the appliance itself is
damaged. If the mains cord is damaged,
you must have it replaced by Philips, a
service centre authorised by Philips or
similarly qualied persons in order to
avoid a hazard.
-Do not place the appliance on or near a
hot gas or electric cooker, or in a heated
oven.
-Do not preheat the appliance.
-Always place a fully assembled bottle
with cap in the baby bottle warmer before
you add water.
-Make sure you add water before you
switch on the baby bottle warmer.
-Hot water can cause serious burns. Be
careful when the baby bottle warmer
contains hot water.
-The accessible surfaces of the appliance
may become hot during use.
-Do not move the appliance when it
contains hot water.
-Always check the baby food temperature
before you feed your child.
Caution
-This appliance is intended to be used in
household and similar applications such
ENGLISH8

as farm houses, bed and breakfast type
environments, sta kitchen areas in
shops, oces and other working
environments, and by clients in hotels,
motels and other residential type
environments.
-Unplug the appliance when it is not in
use.
-Store any excess mains cord in the base
to ensure stability of the baby bottle
warmer.
-Let the appliance cool down before you
clean it.
-Follow the descaling instructions to avoid
irreparable damage.
-Do not try to open or repair the appliance
yourself. You can contact the Philips
Consumer Care Centre in your country (see
www.philips.com/support).
-The food should not be heated for too
long.
-Only use the appliance as described in
the user manual to avoid potential injury
due to misuse.
-The surface of the heating element is
subject to residual heat after use.
ENGLISH 9

Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards
and regulations regarding exposure to electromagnetic elds.
Using the baby bottle warmer
With this baby bottle warmer, you can safely warm and
defrost milk in Philips Avent feeding bottles and milk or baby
food in containers.
The baby bottle warmer helps to preserve the valuable
nutrients and vitamins in breast milk because it never
overheats the milk. If milk becomes too warm, nutrients and
vitamins are damaged. To help preserve the quality of your
breast milk, it is important to heat the milk in a safe and
controlled way. The baby bottle warmer is designed to warm
gently and evenly and to avoid hot spots, as the milk
circulates during warming. The built-in sensor tracks and
controls the milk temperature, to avoid overheating at all
times.
Note: Philips Avent breast milk bags and Philips Avent
2oz/60ml bottles cannot be used in this baby bottle
warmer.
Explanation of settings
-You can choose between the following settings: (Fig. 2)
-Defrost setting: To defrost a bottle or container with frozen
milk or frozen baby food. No warming occurs.
-Milk warming settings: Select one of these settings when
you want to warm a bottle of milk to a safe temperature.
Setting 2 warms your milk to approximately body
temperature. Setting 1 warms your milk to a slightly lower
temperature and setting 3 warms your milk to a slightly
higher temperature.
-Baby food warming setting: Select this setting when you
want to warm a container or jar with baby food.
ENGLISH10

Using the baby bottle warmer to warm milk
1 Put the mains plug in the wall socket (Fig. 3).
2 Place a bottle centrally in the baby bottle warmer (Fig. 4).
Note: To warm milk in a milk storage container, follow the
same steps as indicated for warming milk in a bottle.
3 Fill the baby bottle warmer with the same amount of
drinking water as the amount of milk you want to warm
up (for example, to warm up 125ml/4oz of milk, you need
to use 125ml/4oz of drinking water). If you want to heat
up a large amount of milk (>180ml/6oz), the maximum
water level is approximately 1cm/0.4 inches under the
rim of the baby bottle warmer (which corresponds to
adding 160ml/4.5oz of drinking water). An accurate water
level ensures correct warming performance. (Fig. 5)
4 Select the desired setting (Fig. 6).
Note: Experience teaches that babies may have a
preference for a specific milk temperature. This can be due
to personal preference or external factors (e.g. environment
temperature). All three settings ensure that the milk is
warmed to a safe temperature which is comfortable for your
child and helps to preserve the nutrients and vitamins in the
milk.
5 Press the on/o button to switch on the appliance. The
light in the button lights up to indicate that the baby
bottle warmer is on (Fig. 7).
Note: The baby bottle warmer starts warming up right after
you press the button.
6 The progress indicator starts to ll up gradually with
white light to show the progress of the milk warming
process (Fig. 8).
ENGLISH 11

Note: The progress indicator shows the progress of the milk
warming process. The progress indicator starts flashing when
the appliance is on. When the first warming phase has been
completed, the bottom segment lights up continuously and
the next segment starts flashing to show that the second
warming phase is in progress. These steps continue until the
third warming phase has been completed. Then the entire
progress indicator lights up continuously.
Note: During the warming process, the milk circulates to
ensure even warming. It takes about 10 minutes to warm
90ml/3oz of room-temperature milk. It takes slightly longer
to warm cold milk or a large amount of milk.
Caution: Do not take the bottle out of the baby bottle
warmer while the progress indicator is ashing.
7 When the entire progress indicator lights up
continuously, the milk has reached the set temperature.
-When the milk is warm, you can either take the bottle out
of the baby bottle warmer to feed your baby right away
(see section ‘Feeding your baby immediately’) or you can
keep it warm in the baby bottle warmer (see section
‘Keeping milk warm’).
Increasing the milk temperature
1 If you want the milk to be warmer, you can increase the
milk temperature gradually after it is ready by switching
to milk warming setting 3 and leaving the bottle in the
appliance at the keep-warm mode (Fig. 9).
2 If you just switched o the baby bottle warmer or if it just
switched o automatically, switch it back on without
removing the warm water from it, and follow the above
step (Fig. 10).
3 The baby bottle warmer switches o automatically after
20 minutes of keep-warm mode (Fig. 11).
ENGLISH12