Philips dynalite User manual

14th November 2019 www.philips.com/dynalite
Hardware
Installation Guide
Installing the Data Network
ADo NOT connect DALI or mains power to DyNet data terminals.
1. The data cable is connected to all devices as per the project
schematic following correct color code and DyNet terminations.
Devices may be wired in any order.
2. The recommended connection method is to ‘daisy chain’ devices in sequence, starting at the first device,
then looping in and out of each device, with a single cable terminating at the last device. There should
not be any branching, and only the first and last device should terminate a single cable, all other devices
should terminate two cables.
3. The cable tail can be returned to the original distribution board. Ground and Power can be connected in a
loop but D+ and D– must NOT be connected in a loop.
4. A data cable that is connected to an energized device is live. Do not cut or terminate live data cables.
5. Maximum data cable current = 2 Amps.
6. The data cable should be segregated from mains cables by a minimum of 50 mm (2 in) for shielded cable
and 300 mm (12 in) for unshielded cable. If the data cable crosses over any mains cables, it should cross
at 90°.
7. On Button Panels and Sensors, the Shield wires must be terminated into the shield terminal. Shield wires
are automatically earthed on each controller. For controllers that do not have a shield terminal, the shield
should be twisted together and taped to the cable sheath to maintain continuity.
8. The maximum recommended length for DyNet cables between two network bridges is 800 m (2620 ft).
For cable runs over 300 m (1000 ft), (or baud rates over 9600 bps) a 120 Ωend-of-line resistor must be
installed across the D+ and D- terminals of the DyNet connector strip on the first and last device.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 2
.......................................
14th November 2019 www.philips.com/dynalite
Data Cable Termination
1. Strip off outer jackets of cables being daisy chained.
Shielded cables only: Cut foil or braid flush to outer jacket.
DO NOT cut drain (shield) wire.
2. Strip insulation from each of the conductors.
3. Wind electrical tape (or use a cable tie) around the end of
the two cables to tie them together (see final drawing).
4. Separate the blue and the blue-white wires from each other.
Then combine them with the matching wires from the other
cable; blue to blue and blue-white to blue-white.
5. Twist remaining conductors ends with the matching colored
wires and fold ends in half. Isolate the unused pair with a
connector or tape.
6. Reuse a wire insulation offcut (or heat shrink tubing) and fit
over drain wire.
7. Terminate the wires on the pluggable screw terminal block.
(If used, shrink the heat-shrink tubing)
8. Label or tag the cable appropriately.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 3
.......................................
14th November 2019 www.philips.com/dynalite
Recommended cable types
For serial port connections, the recommended cable is screened RS-485/Cat5e data cable with at least three
twisted pairs, such as DyNet-STP-CABLE-LSZH.
Supplier
Cable
Dynalite
DyNet-STP-CABLE-LSZH
Dynalite
DyNet -SFLAT6-CABLE. limited to 9600 bps. Maximum length 100 m (330 ft).
Ethernet cable
Cat5e
Belden
1502R or 1502P
Belden 9503
Garland
MCP3S
Other cable types may be used provided they are shielded and have three or four twisted pairs with
wire cross section ≥0.5 mm2(20 AWG)
•Use of STP (shielded) CAT5 stranded cable is recommended within the limitations outlined in the table.
•Use of UTP (unshielded) CAT5 stranded cables is not recommended, however, may be allowed for short
runs of under 15 m (50 ft) where there is no risk of noise coupling. UTP cables must be installed in
grounded metal conduits if there is a risk of noise coupling from Mains and Class 1 cables (switched
power circuits, high-frequency power electronics devices, HVAC and motor drives, etc.).
Maximum number of devices on a single cable run
Distances over 300 meters (1000 ft), can be achieved with good quality industry standard cables, such as Belden
1502 or equivalent, only with very low or no DC load. CAT5e/6 has higher resistance. We recommend 300 m
(1000 ft), as a conservative limit for CAT5e/6 provided GND and +V use a twisted pair.
Cable Length Belden 1502P, 1502R Cat5 STP, 8 x 0.2 mm2(24 AWG) Cat5 UTP, 8 x 0.2 mm2(24 AWG)
< 15 m (50 ft)
100
64
64
75 m (250 ft)
55
30
-
150 m (500 ft)
30
15
-
300 m (1000 ft)
15
8
-

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 4
.......................................
14th November 2019 www.philips.com/dynalite
DyNet-STP-CABLE-LSZH
Color Signal
Shield Cover with insulated sleeve
Green/Green-White
Paralleled for Ground
Blue
Data +
Blue-White
Data –
Orange/Orange-White
Paralleled for +12/24 Volts
Brown/Brown-White
Spare pair can be used as a
drain for unshielded cable or
to replace damaged cable
Daisy chained First and last device
DyNet-SFLAT6-CABLE
RJ12 Pins Color Signal
-
1
Silver
Drain
2
White
Ground
3
Red
Data +
4
Green
Data –
5
Yellow
+12 Volts
6
Brown
Not connected
-
Cat5e Ethernet cable
RJ45 Pins Color Signal
1
Green-White
Data +
2
Green
Data –
3
Orange-White
Not connected
4 Blue +12/24 Volts
5 Blue-White +12/24 Volts
6 Orange Not connected
7
Brown -White
Ground
8
Brown
Ground
1 Silver Drain
2 White GND
3 Red D+
4 Green D-
5 Yellow +12 V
6 Brown N/C
1 Green-whit e D+
2 Green D-
3 Ora nge-whit e N/C
4 Blue 12/24 V
5 Blue-whit e 12/24 V
6 Ora nge N/C
7 Brown-whit e GND
8 Brown GND

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 5
.......................................
14th November 2019 www.philips.com/dynalite
Other control cable types
There are two types of data cable commonly used to connect to electronic drivers with LEDs or fluorescent
lamps.
1-10V cabling
1-10V mains rated polarized cabling. Single pair figure-eight cable. Positive wire with dashed line.
DALI Cabling
DALI (and DSI) mains rated non-polarized cabling. Single pair figure-eight cable. Maximum bus length of 300 m
(1000 ft). Maximum 2 V voltage drop between any two DALI devices.
BDALI is not touch-safe and shall be treated as ELV per IEC Classification. DALI could be mains potential.
Only basic isolation is provided. The DALI control cable must be handled as live up to 230VAC.
Total loop resistance on longest run < 18 Ohms. The cable run distance from any point to the DALI controller
should not exceed 300 m (1000 ft).
Wire gauge
Maximum cable distance
1.5 mm2(16 AWG)
150 to 300 m (500 to 1000 ft) Typical
0.75 mm2(18 AWG)
Between 100 to 150 m (330 to 500 ft)
0.5 mm2(20 AWG)
Up to 100 m (330 ft)

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 6
.......................................
14th November 2019 www.philips.com/dynalite
DALI Topology
DALI Broadcast
Each independent lighting group requires individual wiring.
DALI Addressable
DALI bus wiring to DALI enumerated lamp drivers. A DALI universe has up to 64 unique driver addresses.
DALI Multimaster
DALI bus wiring to DALI enumerated lamp drivers and DALI multimaster devices. DALI Multimaster devices
include sensors (e.g. DUS360CR-DALI) and dry contact input devices (e.g. DPMI940-DALI).
DALI Multimaster device and driver limits.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 7
.......................................
14th November 2019 www.philips.com/dynalite
Installing load controllers
AThe control equipment is connected to potentially lethal power supplies. To ensure safety during system
maintenance, Installers must always follow safety installation rules and isolation procedure.
1. When deciding on the mounting position, controllers must be mounted in a dry, well-ventilated location.
Consider that controllers may emit some mechanical noise.
2. Observe recommended spacing around controllers.
3. Ensure suitable circuit overload and safety protection is installed and labelled.
4. DIN rail controllers must be mounted horizontally in a Standard Electrical Enclosure.
5. Wall mounted controllers must be mounted vertically (unless otherwise stated) following ventilation
guidelines.
6. Power and data wires should be segregated as per standard practice. Terminate according to the
installation instructions in compliance with the local wiring code.
7. Mains controlled light fittings are installed and connected to the load controller output terminals.
8. The number of loads connected to individual channels and total box loading must be within the specified
ratings limit for each type of load.
9. Load controllers are connected to mains supply.
10. Auxiliary input is a programmable dry contact interface that is active low. A dry contact is connected
between the AUX and GND terminals on the DyNet connector strip. Ensure that the cable length between
the dry contact and terminal strip is no longer than 20 m (65 ft). DyNet and Aux wiring must meet SELV
installation and insulation requirements as per local wiring code.
DyNet RS-485 Serial Connector with Auxiliary terminal
11. DALI Controllers:
a. Run a two core DALI bus cable to the loads. This cable is in addition to the mains feed.
b. DALI must have no more than 64 drivers per universe.
(Recommend approximately 50 drivers per universe to allow for expansion).
c. DALI MultiMaster controllers can have a limited number of user interface devices on each
universe. Refer to product specification sheet for more information.
12. PWM LED controllers do not connect to mains supply. They require a suitable DC power supply.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 8
.......................................
14th November 2019 www.philips.com/dynalite
Example Installations
DIN rail mounted controllers
Wall mounted controllers

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 9
.......................................
14th November 2019 www.philips.com/dynalite
Installing Gateways
In multi-story buildings, each floor typically contains an independent network segment called a spur. Spurs can
be joined via network gateways to a trunk network (RS-485 or Ethernet) installed in a riser linking all floors
together. The trunk typically connects to the System Manager head-end software or to a BMS enabling full
access to the entire system.
BAll circuits and cables connected to gateways must be SELV/Class 2 (UL).
DyNet RS-485 trunk network and DyNet RS-485 spur network
Ethernet trunk network and DyNet RS-485 spur network
13. For RS-485 networks, terminate both trunk and spur connections to gateway.
a. Spur (Floor sub-network) is terminated to Port 1.
b. Trunk (Building backbone) is terminated to Port 2.
14. An RS-485 gateway is powered from the DyNet network spur connected to
Port 1. Up to 150mA of power from the DyNet network on Port 1 is fed to Port 2,
so providing there is sufficient power available on the spur, it is normally not
necessary to provide a network power supply for the trunk network.
15. When implementing repeaters for long runs, connect the link to Port 2 of both
gateways (and bridges). Shielded cable must be used for long runs (refer to
Recommended cable types). Provide additional DyNet power supplies where
required.
16. Gateways (or bridges) are required when there are more than
100 devices on a run, or the current would exceed the cable limit.
17. RS-485 Gateway Port 2 is used for DMX Receive/Transmit or for third-party integration.
RS-485 Gateway with third party integration options
RS-485 SPUR
Port 1 Port 2
RS-485 SPUR
RS-485 TRUNK
Port 1 Port 2
RS-485 SPUR
RS-485 SPUR
ETHER NET TRUNK

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 10
.......................................
14th November 2019 www.philips.com/dynalite
Installing user interfaces
1. All devices come with three barcode labels, one on the device, and two extras, one for the plan and one
for site documentation.
2. Follow device Installation Instructions to select appropriate physical placement of user interfaces.
3. Take care not to damage the wall surface surrounding the user interface particularly when it has the light
wash feature.
4. All devices must be level and mounted consistently (vertically or horizontally) using the screws provided.
A wall box may be required to comply with local electrical standards. The mounting plate must sit flat
onto the wall surface.
5. Where panels and buttons are engraved, check all labels are in the correct position before clipping into
position.
6. Antumbra and touchscreen sensor holes must be positioned at the bottom of the device. Devices have
arrows to show correct orientation.
7. Antumbra panels should have 30 cm (12 in) clearance from any metal objects or nearby cables (mains
and data). Unearthed nearby metal objects such as stud work and door frames, may lead to false
triggering of the proximity sensor. Ensure wall box and mounting plate are earthed according to the
supplied installation instructions.
8. For all user interfaces, the cable should exit towards the bottom of the panel.
9. Touchscreens require an external power supply.
Antumbra Touchscreen

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 11
.......................................
14th November 2019 www.philips.com/dynalite
Installing sensors
Motion detection positioning
CA single Dynalite sensor can perform motion detection, light regulation and IR receive simultaneously.
CTypical detection range is measured at ≤25°C (77°F). Range is reduced at higher temperatures.
CSensors must receive specified supply voltage (12-18 V or 20-26 V) from the DyNet network. If necessary,
add a network power supply to ensure adequate network voltages during day to day fluctuations.
Position sensor to detect motion in the specified area:
1. Install correct sensor type for location and application
(wall or ceiling mounted, PE, PIR, ultrasonic, high bay, outdoor)
2. Ensure correct orientation for long and short field of view.
3. Install sensor out of direct sunlight.
4. Install sensor away from air conditioning vents and sources of electromagnetic interference.
5. Lift inbuilt mask where applicable, to limit sensor detection area.
Lights trigger only upon entry Using detection area mask May trigger from passersby

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 12
.......................................
14th November 2019 www.philips.com/dynalite
Light regulation positioning
When positioning sensors, there are two methods of light regulation to consider:
•If the sensor is used for Closed loop sensing, then position the sensor so it sees a mixture of indoor and
outdoor light.
•If the sensor is used for Open loop sensing, then position the sensor so it sees the light level from one
light source such as daylight, to adjust light levels elsewhere.
Closed loop light regulation Open loop light regulation
Testing using the inbuilt indicator LED.
When first connected and powered from the network the red indicator LED on the sensor will flash for 3 minutes
when it receives a button message. This allows the installer to confirm that the sensor is terminated correctly and
communicates with other networked devices.
Indicator LED:
Red = PIR motion detection (All sensors).
Green = Ultrasonic motion detection (DUS804CS-UP).
Blue = Low network voltage (DUS804CS-UP)
.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 13
.......................................
14th November 2019 www.philips.com/dynalite
Installing dry contact input devices
DLLI8I8O and DPMI940-DALI
1. Install as close to the switching source as possible.
2. DLLI8I80 has an RS-485 interface and can be connected to eight open/close contacts and eight indicator
LEDs.
3. DPMI940-DALI has a DALI interface and can be connected to four open/close contacts
(must be used with a Dynalite DALI Multimaster controller).
ARefer to installation instructions for cable length, safety insulation, requirements, and limitations.
DLLI8I8O DPMI940-DALI
DDMIDC8
1. Robust device recommended for locations with EMF noise, long cable runs up to 50 m (165 ft), where
additional optical isolation for dry contacts is required or for analog control integration.
2. Can be installed without a DIN rail by extending DIN rail clips to expose mounting screw holes.
3. If used, connect voltage-free contacts or 0-24V AC/DC inputs to any of the eight opto-isolated inputs.
Remove the cover and ensure that the internal jumpers for each input are set to the appropriate 0-24V or
voltage-free setting, according to the input type.
4. Setting the internal jumper to the volt-free position increases the current consumption of the device from
15mA to 40mA. This must be considered when selecting DyNet data cable and supply capacity.
5. If used, connect 0-5 V or 0-10 V inputs to the analog ports. Ensure the input is a maximum of 10 VDC.
Faders can be directly connected to the analog inputs by using the adjacent +5V terminal as a supply.
Suggested fader value is 10K ohm. Analog input circuits must be SELV/Class 2 (UL).
6. Only draw a maximum of 25mA from the +5V terminal.
DDMIDC8

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 14
.......................................
14th November 2019 www.philips.com/dynalite
Installing wireless devices
PDZG-E Wireless Gateway
The PDZG-E connects up to 25 ZigBee nodes (SNS401CMPs) to the Dynalite system over an
Ethernet trunk to a PDEG. This allows communication and control between ZigBee and DyNet
devices anywhere on the network.
The ZigBee protocol’s mesh networking feature allows any device on the network to pass messages along to
other devices within range, even if they are not visible to the gateway. This allows true flexibility with installation
and layout.
As long as each ZigBee node is within 10 meters of at least one other node, it will operate as a seamless
component of the Dynalite system.
SNS401CMP ZigBee Receiver with Multifunction Sensor
The SNS401CMP receives DyNet commands over ZigBee from the PDZG-E and sends DALI
messages over an SR bus. The variant used is the SNS401CMP, which is sold with a circular
mounting plate as shown here.
The SNS401CMP is paired with a Philips Xitanium SR Bridge to control a single DALI
Broadcast channel, or with a Philips Advance SR Bridge to control a 1-10V channel.
The SNS401 also includes a PIR motion sensor and a light level sensor.
RS-485 SPUR
ETHERNET
ETHERNET TRUNK
ETHERNET SWITCH
PDEG PDZG-E
(25x)
SNS401CMP Xitanium/Advance SR Bridge
DAL I/1-10 V Bus
SR Bus
DALI DR IVER
L AMPS
PDEG SENSOR
WIRELESS SPUR
ANT U MBR ACONTROLLER PDTS
5 V
12/24 V

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 15
.......................................
14th November 2019 www.philips.com/dynalite
Energizing the System
Power-up tests
ADanger: The manual override buttons/switches on the controllers do not provide permanent isolation.
Controllers may be fed from multiple circuits. To isolate the controller outputs, power must be
disconnected at the circuit breakers feeding mains to the controller and to any pass-through circuits.
1. Once the network is connected and energized, a button press on any panel, controls all the dimmers.
An unresponsive light indicates that the driver or lamp is faulty or incorrectly wired.
2. Go to the last panel in the run according to the wiring diagram and push buttons 1 and 4 (on and off) to
confirm the integrity of the wiring all the way back to the distribution board. Lights should respond with a
2 second fade time and relays should turn off when all lights are set to 0%. Sensors will flash for
3minutes.
3. On each panel, push the buttons to confirm that the panel is working. The indicator LED should illuminate
on the pushed button. Buttons on other panels should match to track the button pushes.
4. If a button LED indicator does not light, remove the panel and check the wiring and network voltage.
Repair as necessary (refer to the troubleshooting section).
5. For touchscreens, Use the Preset buttons or Sliders on the page to dim channels and confirm that the
touchscreen is communicating with the network.
6. All devices are pre-programmed for out-of-the-box operation. Dynalite load controllers (dimmers) are
set to provide full output by default, irrespective of having the network connected.
7. Where provided for convenience, use the manual override switch to test output circuits and loads. Ensure
the correct circuits switch accordingly.
8. To turn the lights on to full, push the service switch on the load controller three times in succession.
9. To run the DALI flash sequence, push the service switch on the DALI controller four times in succession.
Drivers will flash the lights for 5 minutes, then return to their original state. Hold down the service switch
for 5 seconds to reset the controller and stop the flash sequence.
Default Preset Scenes
The factory default presets for User Interface panels are listed below. Note that some panel types hide or occupy
more than one button position.
Button Preset Light level Button Preset
Light level
1 Preset 1 100% (ON) 5 Preset 5
80%
2 Preset 2 70% 6 Preset 6 60%
3 Preset 3 40% 7 Preset 7 50%
4 Preset 4 0% (OFF) 8 Preset 8
20%

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 16
.......................................
14th November 2019 www.philips.com/dynalite
Controller Service Switch functions
The relevant Service Switch functions are:
•3 pushes = All Channels 100%. You should do this to normalize the connected driver settings.
(DALI Broadcast Channels will setup the connected drivers with Min/Max/PowerOn/SystemFail levels,
and 2 second Fade Time).
•4 pushes = A DALI enumerated controller will run a flash sequence for 5 minutes.
•Push and hold for 5 seconds and release = Device reset
Controller Service LED functions
The Service LED has four signaling modes:
•Blinking slowly (0.5Hz) = Normal operation.
•Blinking normally (1Hz) = Network activity detected or DMX reception.
•Blinking fast (4Hz) = Device communicating.
•Permanently ON or OFF = Fault.
DSome devices support a bicolor service LED. The same blinking pattern is valid for both Red and Green
LEDs. Red is the standard color for all devices. Green shows reception of DyNet heartbeat from another
DyNet device, such as a Gateway.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 17
.......................................
14th November 2019 www.philips.com/dynalite
Fault finding
After completing the power up tests, all controllers should react to a single button push message. If not, check for
any discrepancies between the installation and the installation instructions and check troubleshooting symptoms.
To rectify problems, follow these five steps:
1. Analyze the symptoms.
2. Diagnose the cause.
3. Repair the problem.
4. Verify the solution.
5. Prevent the issue occurring again.
Electrical characteristics
If faults are occurring, one of the first things to check is the typical DyNet voltages. Incorrect voltages may indicate
short/open/crossed circuit or the need for an additional power supply.
Electrical Property Values
Correct Min – Max
network supply voltages:
European (EU): measurement of 12 to 18 V between Gnd and +12 VDC terminals
North American (NA): 20 V to 26 V between Gnd and +24 VDC terminals
Typical Data voltages with
reference to Gnd:
D- between 0.2 VDC to 1.0 VDC
D+ between 0.5 VDC to 3.8 VDC
D- to D+ must be greater than 300 mV
Max network supply/load
current
2 Amps
BMains fed load controllers and power supplies contribute power to the network.
Gateways, button panels, dry contacts and sensors consume power from the network.
Unresponsive devices
If the controls are not responding as expected, follow the procedure below to isolate the fault.
Isolate a fault in the network:
1. Find the midway point of the spur.
2. Break the network into two halves at a field device (user interface or sensor) and power both halves.
3. Perform power-up tests (refer to page 11) in each half of the network; this will identify which half has the
problem.
4. Continue to break the half into quarters etc. Repeat power-up tests until you have found the fault.
If you are still unable to rectify the fault, make a list of device model numbers used in the system and contact
technical support, contact: support.control[email protected]

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 18
.......................................
14th November 2019 www.philips.com/dynalite
Troubleshooting
Load Controller Issues
Symptom Probable cause Solution
Controller does not operate at
all. No Service LED activity.
•Faulty mains supply
connection.
•No power available.
•Controller is damaged.
Check power supply connections to the
device. Check Fuse if fitted.
Replace controller or modules if faulty.
Service LED not lit.
•Supply voltage too low.
•Short circuit on network
wiring.
•Faulty controller.
Check supply voltage. Check for correct
DyNet voltages at each device. Isolate
and energize to determine if the fault is
external to the controller. Replace
controller or modules if faulty.
Device appears to be operating
but all channels stay at full
output.
•Incorrect wiring on DyNet
port.
•Panic function activated.
•Check Manual override
switches.
Check DyNet port wiring, verify button
panel is operating correctly. Check if
emergency state has been activated.
Device operates properly but
circuit breakers continually trip.
•Earth leakage is exceeded or
Short circuit on load.
•Device overloaded.
•Incompatible load.
Check load wiring for short circuits.
Verify device loading with current tester
(remember to de-rate for specific loads
and install conditions).
Check total earth leakage.
Check wiring terminals are tight.
Perform a full power cycle to clear fault
condition.
Dimmable lights won’t dim or
continuously flash.
•Wrong type of driver or
driver incorrectly wired.
•Wrong lamp type.
•Missing or mis-wired
dimming bus cable.
Check that bus cable is connected to
drivers.
Inspect the driver to confirm the driver
type.
Check cable polarity if using 1-10V control.
Check wiring against the driver
manufacturer’s diagram.
Check if the driver is DALI certified. Check
for correct DALI bus voltage: 12–21 VDC.
Can’t control lights but was
previously working.
•Integrated third party system
may require configuration.
Disconnect third party equipment to
isolate the system and identify the cause.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 19
.......................................
14th November 2019 www.philips.com/dynalite
Button Panel, Sensor and Dry Contact issues
Symptom Probable cause Solution
Device does not operate or
indicator/display flashes.
•Wiring issue on DyNet bus.
•No or insufficient power
available.
•Low voltage
Check power supply to the device.
Check for broken wires.
Check controllers are online and
contributing to the network supply.
Add power supply to boost voltage.
Light Wash effect false triggers
•Unearthed metal objects
within 30cm (12 in) of panel.
•Wall box and mounting
plate earthing not applied as
per installation instructions.
Ensure that all metal in the wall and
surrounding metal is Earthed.
Connect the DyNet shield, wall box and
mounting plate to Earth.
Ensure that unused wires have been
connected to correctly Earthed shield
terminal (for example brown/Brown-
white pair).
Touchscreen issues
Symptom Probable cause Solution
Device does not operate at all •No power available.
•Wiring issue.
Check power supply adaptor and
ensure correct supply voltage.
Check for broken wires.
Device is on but not able to
control anything
•Broken power supply wire.
•Broken wire on RS-485 bus.
Check plug is inserted correctly.
Check for broken RS-485 wires.
Check voltage at device for correct
electrical values.
Third party system integration issues
Symptom Probable cause Solution
One or both systems no longer
operate
•Bus contention
(incompatibility)
Install a suitable conversion
gateway/interface (for example, a
DTK622-232).
Dynalite controls operate
intermittently
•Third party system (such as
such as AMX, DMX or
Crestron) is streaming
messages and overriding
DyNet.
Install a suitable conversion
gateway/interface (for example, a
DTK622-232).
Disable DMX.
To ensure safety and prevent damage to the system, appropriate isolation shall be provided. Only SELV/Class 2
(UL) systems shall be connected to non-isolated DyNet interfaces.

Dynalite Hardware
.......................................
Installation Guide
.......................................
Page 20
.......................................
14th November 2019 www.philips.com/dynalite
© 2019 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or
warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in
reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
All other trademarks are owned by Signify Holding or their respective owners.
Document Revision: 0
6