Philips LDTS07 User manual

Lightolier Controls
2828 Trade Center Drive, Suite 130B
Carrollton, TX 75007
+ 1-800-526-2731 (In the United States and Canada)
214-647-7880
Fax: [phone]
www.lolcontrols.com
Lightolier Controls is a Philips Controls brand.
This manual is for informational use only and is subject to change without notice.
Lightolier Controls assumes no responsibility or liability for any claims resulting from errors or inaccuracies that may appear in this manual.
Version as of: July 6, 2009
Document: 85-6369A0
Lytemode Designer Suite Touch Screen User’s Guide
© 2009 Philips Controls. All Rights Reserved.

DESIGNER SUITE TOUCH SCREEN USER’SGUIDE CUSTOMER SERVICE
1
Table of Contents
About the Lytemode Designer Suite System ...................................................................................................2
Designer Suite Touch Screen Overview ..........................................................................................................3
Installation .......................................................................................................................................................4
LDTS07 (Wall-Mount) .............................................................................................................................4
LDTS07RM (Rack Mount) ......................................................................................................................5
Setup and Operation ........................................................................................................................................6
Customer Service
Technical and Sales assistance for Lytemode products are available worldwide.
Phone: [phone] (In the United States and Canada)
[phone] (Worldwide)

ABOUTTHE LYTEMODE DESIGNER SUITE SYSTEMDESIGNER SUITE TOUCH SCREENUSER’SGUIDE
2
About the Lytemode Designer Suite System
The Lytemode Designer Suite System is designed to control architectural lighting by distributing
both power and intelligence. The system provides processing power and control at each respective
Pushbutton, Slider or Touch Screen Station, eliminating the need for a central processor.
Slider Stations provide individual control of up to 15 channels, as well as 8 dynamically programmable
pushbuttons to provide one-touch access to a variety of commands including: preset scenes, toggle on/
off, smart"matrix" commands, room link, raise, lower and more.
By combining Lytemode Designer Suite Slider Stations, Lytemode Designer Suite Button Stations and
Lytemode Designer Suite Touch Screens, the system provides remote access to scenes, master raise/
lower control, multi-room partition control, station lockout, toggle on/off, smart "matrix" commands,
and more.
Lytemode Designer Suite Stations are compatible with Lyteswitch, Capio Plus, Optio, and
Intelligent Raceway dimming systems, as well as Intelligent Power Systems (IPS) Dimmer Strips,
Dimmer Boxes, and Bak Pak dimmers.
Lytemode Designer Suite products are controlled by the Lytemode network protocol. All Lytemode
Designer Suite control devices must be connected to the system and given a unique ID (or address) in
order to interact properly. The ID identifies the device onthe network and allows the device toavoid
network collisions when transmitting data.

DESIGNER SUITE TOUCH SCREEN USER’SGUIDE DESIGNER SUITE TOUCH SCREEN OVERVIEW
3
Designer Suite Touch Screen Overview
The Lytemode Designer Suite Touch Screen provides a simple-to-use graphical interface for
controlling Designer Suite Systems. The color screen mimics the layout of any selected station. Access
to programmable pushbuttons and channel adjustments can be made with just a few simple touches of
the screen.
The following Touch Screen models are covered in this manual:
• LDTS07 - 7" Full Color VGA Touch Screen, Wall-Mount
• LDTS07RM - 7" Full Color VGA Touch Screen, Rack-Mount
All models feature a Real Time Clock, which allows a large number of lighting events to coincide with
specific times, days, or sunrise/sunset, including exceptions for holidays or other events.

INSTALLATION DESIGNER SUITE TOUCH SCREEN USER’SGUIDE
4
Installation
The Designer Suite Touch Screen is available in two mounting configurations: wall-mount, surface or
flush (LDTS07) and rack-mount (LDTS07RM). Refer to appropriate installation method below.
The Lytemode ILS Network consists of a single CAT5e cable connecting all ILS devices in a daisy
chain manner. All units connect to the network using a 9-pin connector (included).
LDTS07 (Wall-Mount)
To install wall-mount unit:
Step 1. Unpack LDTS07 Touch Screen and inspect for any signs of shipping damage.
Step 2. Route ILS network cable through appropriate knock-out hole and install rough-in
box (sold separately) into wall (Figure 1).
Step 3. Connect ILS network cable to Touch Screen ILS connector.
Step 4. Install Touch Screen onto rough-in box using four #6 flat head screws.
Figure 1: Installing LDTS07 Wall-Mount Touch Screen
Rough-In Box
Knock-Out Hole
Touch Screen Assembly
(Wall-Mount Version)
ILS 9-Pin
Connector
From ILS Network
(Part # ILSCLBTSII,
TOP VIEW
ILS Network
1WH/OR(+Data)
2 OR (- Data)
3SHIELD
4WH/GN(+Volts)
5 GN (Ground)
6WH/BL(+Volts)
7 BL (Ground)
8WH/BR(+Volts)
9 BR (Ground)
PIN SIGNAL
WARNING!
Remove power from house service before connecting
any wiring or cables to the Designer Suite Touch Screen.
#6 Flat Head Screw (4)
All other connectors are not
applicable to this installationConnection
Surface
Mounting
Hole (4)
Sold Separately)

DESIGNER SUITE TOUCH SCREEN USER’SGUIDE INSTALLATION
5
LDTS07RM (Rack Mount)
To install rack-mount unit:
Step 1. Unpack LDTS07RM Touch Screen and inspect for any signs of shipping damage.
Step 2. Connect ILS network cable to Touch Screen ILS connector (Figure 2).
Step 3. Install in rack using standard rack mounting hardware.
Figure 2: Installing LDTS07RM Rack-Mount Touch Screen
Touch Screen Unit
(Rack-Mount Version)
Rack Mount
Screw (4)
ILS 9-Pin
Connector
1 WH/OR (+ Data)
2 OR (- Data)
3SHIELD
4WH/GN(+Volts)
5 GN (Ground)
6WH/BL(+Volts)
7 BL (Ground)
8WH/BR(+Volts)
9 BR (Ground)
PIN SIGNAL
WARNING!
Remove power from house service before connecting
any wiring or cables to the Designer Suite Touch Screen.
From ILS Network
TOP VIEW
ILS Network All other connectors are not
applicable to this installationConnection
(not included)

SETUP AND OPERATION DESIGNER SUITE TOUCH SCREEN USER’SGUIDE
6
Setup and Operation
The Lytemode Designer Suite Touch Screen is programmed using Lytemode Designer Suite
Software. The software runs on a PC connected by an ILSCL232 Interface to the Designer Suite
system. For specific programming instructions, refer to the Lytemode Designer Suite Software manual.

THREE YEAR LIMITED WARRANTY
The Philips Controls product, when properly installed and under normal conditions of use
(without overload, abuse or alteration), is warranted to you, the original user, for a period
of three years form the date of original retail purchase, to be free from defects in materials
and workmanship. If during the warranty period you believe the purchased product or any
part thereof has such a defect, you must return the product (or part) at your cost during
such period, with proof of purchase (or if installed by a third-party a written explanation
of installation transaction with proof of date), to Philips Controls, 2828 Trade Center Dr.
Ste. 130B, Carrollton, TX 75007, for repair or replacement (or to an authorized Philips
Controls supplier which agrees in advance to handle the return and replacement by factory
authorization). If the product or part is found by Philips Controls to have been defective in
material or workmanship it will be repaired or replaced (as deemed necessary by Philips
Controls), and the replacement will be returned to you free of charge. The original user is
solely responsible for any costs associated with removal and
re-installation of the product and shipping to Philips Controls or its authorized supplier.
PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF
MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED
WARRANTY PERIOD SET FORTH ABOVE, AND OTHERWISE DISCLAIMS ALL
IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS.
Some states disallow certain limitations on implied warranties so you should consult your
state law if you have a questions regarding this limitation and disclaimer. Philips Controls
disclaims any and all liability for incidental, consequential, special or indirect damage
arising out of any claimed breach of warranty or otherwise. However, some states do not
allow exclusion or limitation of such damages, so this disclaimer may not apply to you.
The remedy provided in the Limited Warranty for defective products is the user’s sole and
exclusive remedy, subject to your state law. Further, this Warranty gives the user specific
legal rights, and the user may also have other rights which may vary from state to state.
If you believe warranty claim is warranted, you may contact your nearest authorized
Philips Controls supplier. If one does not exist in your area, please contact Philips
Controls Customer Service at the above address (or at 1-800-526-2731), or please visit us
at www.lolcontrols.com.