Philips HD4690 User manual

ServiceManual
Philips Consumer Lifestyle
Published by Philips Consumer Lifestyle Printed in the Netherlands © Copyright reserved Subject to modification
Kettle
HD4690
09/08
PRODUCT INFORMATION
- Product meets the requirements regarding interference
suppression on radio and television.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as laid
down officially established at this moment.
TECHNICAL INFORMATION
- Voltage : 220 - 240 V
- Frequency : 50 - 60 Hz
- Power consumption : 2000 - 2400 W
- Contents Kettle : 500 - 1500 cc
- Colour setting : Anodised brushed Aluminium
- Sounding : Mechanical boil ready signal
- Indications : Blue light ring in base plate

HD4690
2-4
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- Disassembly Heater assy.
Remove the base by unscrewing the 8 Torx screws.
Disconnect the wires that are connected to the heater assy.
Remove the switch assy by removing the 3 Nuts.
Remove the Cir clip that fixes the heater assy.
Open the lid and gently push (force maybe needed) on the
inside of the heater.
The heater and Gasket will move out of the Kettle body.
Remove the Gasket from the heater.
- Re-assembly the heater assy.
Place the gasket on the heater assy. (see picture for
placement details.)
Make the outside of the gasket and the inside of the Kettle
housing were the gasket will be placed wet with plain water.
Gently push the heater assy with gasket equable in the
Kettle body. While pushing inwards check if the gasket
keeps well around the heater assy.
The heater assy and gasket has to be pushed over the ridge.
Check visual if the gasket is correct placed.
Reassembly the Cir clip for fixation of the heater assy.
By filling the kettle with plain water and leave it for half an
hour, you can check if the gasket properly sealed the Kettle.
- Reassemble the switch assy.
Connect the wires again.
Fix the base again.
Check the functions of the Kettle.
REPAIR INSTRUCTION
- Electrical circuit
When the appliance does not work, check the electrical
Circuit.
- De-scaling
Fill the kettle with water up to three-quarters of the
maximum level indication and press the on/off switch.
After the kettle has switched itself off, add white vinegar
(8% acetic acid) or an appropriate descaler up to the
maximum level indication.
Leave the solution in the kettle overnight.
Empty the kettle and rinse the inside thoroughly.
Repeat this procedure if there is still some scale left in the
kettle.
- Cleaning filter
Clean the filter by rinsing it under a running tap.
If necessary, you can use a soft nylon brush.
The scale filter can also be cleaned in the dishwasher or
clean the filter by de-scaling it in the same way as the kettle.
Let the filter soak in a cup of warm water with some white
vinegar or an appropriate descaler.
Take the filter out of the cup and rinse it thoroughly.
OPTIONAL (accessories)
- No specific issues.
PARTS LIST
Pos Service code Description
1
2
3
4
5
6
7
8
9
10
11
12
9965 000 32729
9965 000 32730
9965 000 32728
9965 000 32731
9965 000 32727
9965 000 32725
9965 000 32724
9965 000 32726
9965 000 32723
9965 000 32732
9965 000 32715
9965 000 32716
Alu lid wrap
Lid opening switch
Lid cover
Lid locker
Lid seal ring
Alu body wrap
Filter
Wire filter
Lower filter
Damper assy complete
Handle cover
Handle
Pos Service code Description
13
14
15
16
17
18*
19
20*
21
22
23
24
9965 000 32722
9965 000 32721
9965 000 32717
9965 000 32714
9965 000 32713
9965 000 32720
9965 000 32712
9965 000 32719
9965 000 32718
9965 000 32709
9965 000 32710
9965 000 32711
Seal ring
Heater
Switch toggle
Switch ring
Switch lever Alu
Circlep
Lower steam guide
Switch assy
Kettle base
Plug CS7
Base Cover
Rubber feet
* Not available for appliances produced after week 832
= changed

HD4690
3-4
EXPLODED VIEW
1
10
20
21
18
13
14
15
16
19
17
11
125
6
9
7
8
3
4
2

HD4690
4-4
EXPLODED VIEW
22
23
24