Philips CDR779 User manual

Published by DP 0071 Service DPS Hasselt Printed in the Netherlands Subject to modification 53104 125 40190
©
Copyright 2000 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic, mechanical,
photocopying, or otherwise without the prior permission of Philips.
Compact disc recorder CDR779
/00
AUDIO CD RECORDABLE/REWRITABLE
OPEN / CLOSE
PLAY/ PAUSE STOP
REC
TYPE
Recordable
ON / OFF
OPEN / CLOSE
PLAY/ PAUSE STOP
EXT
SOURCE
ERASE
FINALIZE
OPEN / CLOSE
PLAY/ PAUSE STOP
EXT
SOURCE
ERASEFINALIZE
AUDIO CD RECORDABLE/REWRITABLE
AUDIO CD RECORDABLE/REWRITABLE
RECORD
CDR CD
DOUBLE SPEED
CDR775 AUDIO CD RECORDER
6
5
6K
K
J
J
5
AUDIO CD PLAYBACK
AUDIO CD PLAYBACK
PLAY/PAUSE
STOP OPEN/CLOSE
PLAY/PAUSE
STORE/
MENU
STORE/
MENU
EASY JOG
EASY JOG CANCEL/
DELETE
CANCEL/
DELETE
STOP OPEN/CLOSE
ENTER
IR SENSOR
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN
I
I
CD
RW
CHANGER
SYNC MANUAL RECORD
REM
TOTAL
AB
ALL
TRACK
TIME STEP
TRACK
CD
RW
12
3456789
10 11 12 13 14 15 16 17 18 19 20 +
DISPLAY SCROLL DJ MODE
REPEAT
SHUFFLE
PROG PHONES
CL 96532086_000.eps
080999
SERVICING
For servicing CDR779, the set can be devided into three parts
1. The display board (partly) 1002, the I/O board 1004, the
headphone board (partly) 1002, the IR board (partly) 1002, the
ON/OFF & Standby LED board (partly) 1002 and the CD-out
board (partly) 1002 have to be repaired at component level. The
power supply unit 1003 is available as spare part, but can also be
repaired at component level.
2. The CDR module (containing the CDR loader 81, CDR main
board 1001 and loader bracket 82, 83) can also be repaired at
component level with the help of COMPAIR release 1.6 and
higher. With this tool the diagnosing of the set can be done in an
interactive way. In the tool also the adjustment procedure has
been implemented. This is absolutely necessary in case the CDR
mainboard and/or (CDR loader) CDM is disconnected from the
matched production combination. Only designated workshops
can perform these repairs. Please send the complete set to the
designated workshop.
3. The CD module (containing the CD loader 131, CD mainboard
1005 and loader bracket 132) is a new module with VAL1250
loader assy but also a separate CDM and separate loader parts
will be available via service stock. The CD mainboard can be
repaired at component level.
Also available : Circuit Description “The Basics of Compact Disc
Recordable/Rewriteable”. Service codenumber 4822 725 25242.
Second line Repairmanual . Service codenumber 3104 125 40110.
Contents Page
1. Technical Specifications 2
2. Warning and Servicing Hints 4
3. User Instructions 7
4.
Mechanical Instructions
Wiring Diagram CDR 19
Wiring Diagram CD loader 20
Exploded View CDR 21
Exploded View CD loader 22
Dismantling Instructions 23
5.
Block diagram, Circuit diagrams and PWB’s Diagram PWB
Overall Blockdiagram 24
Display Board 25 26
IR / On/Off &Standby LED Board 27 27
Headphone / CD-out Board 28 28
I/O Board: EXT DAC (Diagram 1) 29 35
I/O Board: Cinch (Diagram 2) 30 35
I/O Board: Mic ADC (Diagram 3) 31 35
I/O Board: Power supply (Diagram 4) 32 35
I/O Board: DAC filter (Diagram 5) 33 35
I/O Board: DAC (Diagram 6) 34 35
Power Supply Unit 36 37
CD-Mainboard: Decoder & Servo (Diagram 1A) 38 42/43
CD-Mainboard: Servo drivers (Diagram 1B) 39 42/43
CD-Mainboard: Audio (Diagram 1C) 40 42/43
CD-Mainboard: Microprocessor (Diagram 2) 41 42/43
6. Diagnostic Software 45
7. Faultfinding Trees 49
8. Faultfinding Guide 55
9. List of Abbreviations 69
10. Partslist (mechanical and electrical) 75

Technical Specifications CDR779
GB 2 CDR7791.
1. Technical Specifications CDR779
1.1 General
Mains voltage : all range version 84-
230V
Mains frequency : 50-60 Hz
Power consumption : 12W
DC output : +5V ±10%, 50mA
max.
1.2 Input/output
1.2.1 Line output (CDR & CD)
Output level : 2Vrms at 0dB
Output resistance : 200Ω
1.2.2 Line input
Input sensitivity : 500mVrms
Input impedance : 50kΩ
Max. input voltage : 2.5Vrms
1.2.3 Digital output (CDR & CD)
Format : AES/EBU format
according IEC958
(consumer format)
Sampling frequency : 44.1kHz
Output resistance : 75Ω
1.2.4 Digital input
Format : AES/EBU format
according IEC958
(consumer format)
Sampling frequency : 32 to 48kHz
Input resistance : 75Ω
1.2.5 Optical input
Format : AES/EBU format
according IEC958
(consumer format)
Sampling frequency : 32 to 48kHz
1.3 Audio performance
1.3.1 Cinch analog output (CDR play-back)
Output voltage : 2Vrms ±2dB. (0dB
digital).
Frequency range F.R. : 20Hz < F.R. <
20kHz.
Amplitude linearity : ±0.15dB.
: typical.: ±0.1dB.
Channel unbalance : <0.3dB at 1kHz.
:typical:±0.2dB.
Phase non-linearity : <0.2deg at 1kHz.
Outband attenuation : 50dB above 30kHz.
Channel separation : >100dB at 1kHz.
: typical: 110dB.
: >84dB from 20Hz.
until 20kHz.
: typical: >85dB.
S/N-ratio A-weighted : >99dB.
: typical: 100dB.
S/N-ratio unweightes : >97dB.
: typical: 98dB.
Dynamic range : > 94dB. at 1kHz.
: typical: 95dB.
THD+N : > 89dB from 20Hz.
until 20kHz.
: typical: 90dB.
1.3.2 Cinch analog input/output (monitor path CDR)
Measued with Audio precision system one.Input voltage is
2Vrms.
input voltage : 2Vrms ±2dB. (0dB
digital).
Frequency range F.R. : 20Hz < F.R. <
20kHz.
Amplitude linearity : ±0.2dB.
: typical.: ±0.1dB.
Channel unbalance : < 0.2dB at 1kHz.
:typical:±0.15dB.
Input resistance : 25k(
Phase non-linearity : < 0.2deg at 1kHz.
Outband attenuation : 50dB above 30kHz.
Channel separation : > 90dB at 1kHz.
: typical: 100dB.
S/N-ratio A-weighted : > 87dB.
: typical: 93dB.
S/N-ratio unweighted : > 87dB.
: typical: 90dB.
Dynamic range : > 86dB. at 1kHz.
: typical: 90dB.
: > 86dB from 20Hz.
until 20kHz.
: typical: 90dB.
THD+N : > 86dB from 20Hz.
until 20kHz.
: typical: 87dB.
1.3.3 Cinch analog output (CD play-back)
Output voltage : 2Vrms ±2dB. (0dB
digital).
Frequency range F.R. : 20Hz < F.R. <
20kHz.
Amplitude linearity : ±0.3dB.
: typical.: ±0.1dB.
Channel unbalance : <0.3dB at 1kHz.
:typical:±0.2dB.
Output resistance : 200(.
Phase non-linearity : <0.2deg at 1kHz.
Outband attenuation : 60dB above 30kHz.
Channel separation : >95dB at 1kHz.
: typical: 100dB.
: >90dB from 20Hz.
until 20kHz.
: typical: >93dB.
S/N-ratio A-weighted : >98dB.
: typical: 100dB.
S/N-ratio unweighted : >92dB.
: typical: 95dB.
Dynamic range : >92dB. at 1kHz.
: typical: 96dB.
: >90dB from 20Hz.
until 20kHz.
: typical: 96dB.
THD+N : >82dB from 20Hz.
until 20kHz.
: typical: 85dB.

Technical Specifications CDR779 GB 3CDR779 1.
1.3.4 Headphone output (all functions)
Output voltage : 2Vrms (0dB)/16Ω
S/N : > 80dB
THD+N : > 78dB
Channel separation : > 60dB between
20Hz until 20kHz
1.4 Laser device
Material : GaAlAs
Wave length : between 780 and
800nm (at 25°C)
Laser output : 1mW max. during
reading, 20mW
max. during writing
Class : 3B
1.5 Dimensions and weight
Number and height of feet : 4x11mm foiled
Apparatus tray closed (WxDxH) : 435x305x75mm
(without feet)
Weight without packaging : 3.2kg
Weight with packaging : 4.2kg

Warnings and Servicing Hints
GB 4 CDR7792.
2. Warnings and Servicing Hints
SHOCK, FIRE HAZARD SERVICE TEST:
CAUTION: After servicing this appliance and prior to returning to customer, measure the resistance between
either primary AC cord connector pins (with unit NOT connected to AC mains and its Power switch ON), and the
face or Front Panel of product and controls and chassis bottom,
Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC
power is applied, and verified before return to user/customer.
Ref.UL Standard NO.1492.
NOTE ON SAFETY:
Symbol : Fire or electrical shock hazard. Only original parts should be used to replace any part with symbol
Any other component substitution(other than original type), may increase risk or fire or electrical shock hazard.
FATTENTION
Tous les IC et beaucoup d'autres semi-
conducteurs sont sensibles aux décharges
statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu'aucune précaution
n'est prise a leur manipulation.
Lors de réparations, s'assurer de bien être
relié au même potentiel que la masse de
l'appareil et enfiler le bracelet serti d'une
résistance de sécurité.
Veiller a ce que les composants ainsi que les
outils que l'on utilise soient également a ce
potentiel.
DWARNUNG
Alle IC und viele andere Halbleiter sind
empfindlich gegen elektrostatische
Entladungen (ESD).
Unsorgfältige Behandlung bei der Reparatur
kann die Lebensdauer drastisch vermindern.
Sorgen sie dafür, das Sie im Reparaturfall
über ein Pulsarmband mit Widerstand mit
dem Massepotential des Gerätes verbunden
sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls
auf diesem Potential.
NL WAARSCHUWING
Alle IC's en vele andere halfgeleiders zijn
gevoelig voor elektrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie
kan de levensduur drastisch doen
verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
IAVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevita potrebbe essere fortemente
ridatta in caso di non osservazione della piu
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello
della massa dell'apparecchio tramite un
braccialetto a resistenza.
Assicurarsi che i componenti e anche gli
utensili con quali si lavora siano anche a
questo potenziale.
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce
life drastically.
When repairing, make sure that you are
connected with the same potential as the
mass of the set via a wrist wrap with
resistance.
Keep components and tools also at this
potential.
GB WARNING
GB
Safety regulations require that the set be restored to its original condition
and that parts which are identical with those specified be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkelijke
toestand wordt terug gebracht en dat onderdelen, identiek aan de
gespecifieerde worden toegepast.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten.
Der Originalzustand des Gerats darf nicht verandert werden.
Fur Reparaturen sind Original-Ersatzteile zu verwenden.
I
Le norme di sicurezza esigono che l'apparecchio venga rimesso nelle
condizioni originali e che siano utilizzati pezzi di ricambiago idetici a quelli
specificati.
F
Les normes de sécurité exigent que l'appareil soit remis a l'état d'origine et
que soient utilisées les pièces de rechange identiques à celles spécifiées.
“Pour votre sécurité, ces documents
doivent être utilisés par des
spécialistes agrées, seuls habilités à
réparer votre appareil en panne.”
CL 96532086_021.eps
080999

Warnings and Servicing Hints GB 5CDR779 2.
SERVICING HINTS
In the set, chip components have been applied. For disassembly and assembly check the figure below.
CL 96532086_022.eps
080999

Warnings and Servicing Hints
GB 6 CDR7792.
CL 96532086_023.eps
080999

Directions for use GB 7CDR779 3.
3. Directions for use
English
9
1Connection to mains 2ANALOG OUT ............connects CD player deck to the
line input of an amplifier (left and right)
3DIGITAL OUT CD ......connects CD player deck to the
digital coaxial input of e.g. amplifier or recording device
4ANALOG IN ................connects to the line output of an
amplifier (left and right)
5ANALOG OUT CDR & CD
......................................connects to the line input of an
amplifier (left and right)
6DIGITAL IN..................connects to the digital coaxial
output of an external CD player
7DIGITAL OUT CDR & CD
......................................connects to the digital coaxial
input of e.g. amplifier or recording device
8OPTICAL IN ................connects to the digital optical
output of an external CD player
1REM/REC TIME ..........remaining time/remaining
recording time/recording time
2TRACK ........................track number 3
FE
..............................balance (lights during balance
adjustment)
4TOTAL REM
TRACK TIME ..............total or remaining time of disc or
track
5}................................remote control active 6STEP ............................indicates the number of tracks in a
program
7Track bar ....................indicates
- tracks on a disc or in a program - track in play
8+ 0 ..............................disc or program contains more
than 20 tracks
9PROG(ram) ..................flashes during programming/lights
in program mode
0REPEAT TRACK/ALL..lights up when a track/ complete
disc (or program) is repeated
!SCAN ..........................lights up when the first 10
seconds of each track are played
@SHUFFLE......................plays tracks in random order #
s
..............................CD player deck selected
$c..............................CD inserted (a pre-recorded CD or
finalized CDR or CDRW disc)
%fRECORDg............lights during recording from the
internal CD
^L/R; ;........................record/play level bar. Indicates the
audio signal level
&j k ........................DJ mode selected *iCHANGERh........changer mode selected
(;..................................pause function active
)B................................lights during play ¡R(W) ............................unfinalized CDR(W) disc inserted ™0................................lights during recording £ANALOG......................- analog input selected for
external recording
- analog recording
≤OPTICAL I ..................optical input I selected for external
recording
∞DIGITAL I ....................digital input I selected for external
recording
§SYNC ..........................automatic or synchronised start of
external recording
≥MANUAL ....................manual operation of external
recording
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17 18 19 20 +
1 2 3 4 5
10
1617
19202122
23
24
27 26 25
12131415
6
7
8 9
11
18
DISPLAY indicationsConnections at the back
CONTROLS AND CONNECTIONS DISPLAY
English
8 CD recorder 1ON/OFF ........................turns the CD recorder ON or OFF (if
the recorder is in Standby mode, any key press will activate the CD recorder)
2Standby indicator 3Disc tray 4OPEN/CLOSE /..........opens/closes disc tray 5PLAY/PAUSE 2;......starts play/interrupts play or
recording
6STOP 9........................stops/clears a program 7REC(ord) TYPE ............selects recording modes
8RECORD ......................starts recording, finalizing, erasing 9FINALIZE ....................selects finalize mode 0ERASE..........................selects erasing mode (disc or track) !EXT SOURCE ..............selects external input source @CDR ............................selects CD recorder deck
display/keys
CD player $CD ..............................selects CD player deck
display/keys
)PLAY/PAUSE 2;......starts play/interrupts play ¡STOP 9........................stops/clears a program ™OPEN/CLOSE /..........opens/closes disc tray £Disc tray General #Display..........................information screen %Q............................- searches backward
- cursor control in Menu/Prog.
review mode
^R............................- searches forward
- cursor control in Menu/Prog.
review mode
&¡EASY JOG ™........- previous/next track (Play and
(rotate) Program mode)
- recording level control (recording) - selects settings (menu on)
ENTER..........................- plays selected tracks (push) - selects settings in Menu mode
- programs track numbers
*STORE/MENU ............- stores Menu settings
- enters Menu mode
(CANCEL/DELETE ......- deletes tracks from a program
- deletes text in Menu mode - returns to a higher level in the
menu
≤IR sensor ....................receives signals from the remote
control
∞PHONES......................socket for headphones §DJ MODE ....................separate play of CD recorder deck
and CD player deck
≥REPEAT........................repeats play (All, program or track) •SCROLL........................activates scrolling of text over the
display (once)
ªDISPLAY......................selects display information,
permanent text scrolling and time
ºSHUFFLE......................plays CD(RW) or program in
random order
⁄PROG(ram) ..................opens/closes program memory Note: Unless stated otherwise, all controls are on the front of
the CD recorder. When provided on the remote control, you can also use the corresponding buttons, after selecting the CD recorder deck or CD player deck by pressing CD or CD.
Controls on the front
CONTROLS AND CONNECTIONS
AUDIO CD RECORDABLE/REWRITABLE
OPEN / CLOSE
PLAY / PAUSESTOP
REC
TYPE
Recordable
ON / OFF
PHONES
EASY JOGSTORE/
MENU
OPEN / CLOSE
PLAY / PAUSESTOP
EXT
SOURCE
ERASE
FINALIZE
AUDIO CD RECORDABLE/REWRITABLE
CDR
CANCEL/
DELETE
RECORD
CD
DOUBLE SPEED
IR SENSOR
AUDIO CD PLAYBACK
AUDIO CD PLAYBACK
ENTER
DISPLAYSCROLLDJ MODE
REPEAT
SHUFFLE
PROG
CDR 779 AUDIO CD RECORDER
DIGITALDIGITAL
INOUT
OUT
OUT
OPTICAL
IN
ANALOG
ANALOG
IN
L
R
L
R
OUT
L
R
CD
REMTRACK
RECTIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE
REPEAT SCAN
I I
CD
RW
CHANGER
SYNCMANUALRECORD
REM
TOTAL
A-
ALL
TRACK
TIMESTEP
TRACK
CD
RW
123456789
10 11 1213 141
516 17 18 1920 +
CD
CD
CDR
CDRCDR
CD
CDR
1 87
6
5432
26 25
14 15 16 17 18 19 20 21 22
23 24
4 65 9 10 11 12 13
3031 29 2728
7 8
1 2
3

Directions for use
GB 8 CDR7793.
English
11
Menu messages NO TRACKS ....................when attempting to edit text for a
disc which has no tracks
TEXT EDIT ....................when entering Text Edit mode ALBUM ARTIST ............when editing or erasing an artist
name
ALBUM TITLE ..............when editing or erasing a title ARTIST TR X................when editing or erasing an artist
name per track
TITLE TR X ..................when editing or erasing a title per
track
TEXT ERASE ..................when entering Text Erase mode ALL TEXT ......................when entering All Text mode ERASE OK ......................when confirmation for erasing has
to be given with ENTER key
ERASE ALL OK ............when confirmation for erasing has
to be given with ENTER key
ERASE MEMORY ............when waiting for confirmation
when erasing a disc
MEMORY VIEW ..............when selecting text review per
unfinalized disc in memory
MEMORY EMPTY ............when REVIEW is selected while no
text is in memory
AUTO TRACK ..................when selecting auto track
increment ON or OFF
ON ......................................auto track increment on OFF ....................................auto track increment off SET BALANCE ..............when selecting BALANCE NO TEXT..........................no text stored for disc
For playback on the CD recorder (and/or CD player deck) the following outputs are present - Digital coaxial output (CD & CDR); - Analog output (CD & CDR). We advise you to connect these to the TAPE or CDR input on your amplifier. For external recording the following inputs are present - Digital optical input; - Digital coaxial input; - Analog input. For playback of CD player deck separately (DJ mode) from the CD recorder the following outputs are present - Digital coaxial output (CD); - Analog output (CD). We advise you to connect these to the CD input on your amplifier. The connections you make will depend upon the possibilities your audio equipment offers. Please refer to the user manuals for your other audio equipment first. Digital recordings (optical or coaxial) give the best performance in audio and usability (e.g. auto-track). (The digital optical connection is less sensitive to external disturbances). If your equipment does not offer digital connections, the high quality Analog-Digital-Convertor of your CD recorder will ensure very good audio performance when recordings are made from the analog input. Playback via the digital coaxial output of the CD recorder gives the best audio performance. If your equipment does not offer digital connections, the high quality Digital-Analog-Convertor of the CD recorder ensures a very good sound quality via the analog output. We advise you to always establish both digital and analog connections. In this way you can always make analog recordings when digital recording is not possible. We have described the most common ways of connecting the CD recorder. If you still have difficulties with the connections you can always contact the Philips Consumer Service desk in your country.
Connections general
EASY JOGSTORE/
MENU
CANCEL/
DELETE
AUDIO CD PLAYBACK
ENTER
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
MENU messages - See Menu mode
DISPLAY INSTALLATION
English
10 Messages, as listed and explained here, may appear on the display for your guidance. General READING..........................reading disc information OPEN..................................during tray opening CLOSE ..............................during tray closing NO DISC..........................no disc inserted, disc unreadable
or disc inserted upside down
PROG FULL ....................program full INSERT DISC ..............insert disc or insert disc in correct
way
WRONG DISC/ ................inserted disc is not an audio CD USE AUDIO CD UNFINALIZED ..............unfinalized CDR(W) disc MEMORY XXù ............indicates the amount of text
memory used for unfinalized discs
Recording WAIT..................................- when STOP 9is pressed during
recording
- when STOP 9is pressed during
recording the first 4 seconds of a track
UPDATE ..........................updating disc contents DISC FULL ....................no more recording possible DIGITAL 1 ....................digital coaxial input 1 selected OPTICAL ........................digital optical input selected ANALOG ............................analog input selected COPY PROTECT ............no digital recording can be made
of the external source
NOTFINALIZED ............when opening the tray with an
unfinalized disc inserted (CD recorder)
RECORD FAST ..............high speed recording selected REC LISTEN ..................listen speed recording selected MAKE CD..........................high speed recording of a
complete disc and Auto Finalize function selected
REC EXT DISC ............synchronised start of recording
from external source selected
REC EXT MAN................manual start of recording from
external source selected
_XX DB ............................level is being adjusted DOES NOT FIT ............time left on CDR(W) disc is not
enough for proposed recording
ANALOG REC ..................copy prohibited track found during
recording. Track will be copied analog (Copy Protection Regulations)
ERASE TRACK ..............when erasing one or more tracks ERASE DISC ..................when erasing a disc FINALIZE CD ..............when finalizing a disc FINALIZED ....................when trying to finalize an already
finalized disc
CHECK INPUT ..............when RECORD is pressed while no
digital source is detected
XX XX ERASE................time countdown when erasing a
track or a disc
XX XX FINAL................time countdown when finalizing a
disc
PRESS RECORD ............to start manual recording,
finalizing or erasing
START SOURCE ............to start synchronised recording
from a source (e.g. CD player)
FINALIZED CD ............when trying to record on a
finalized CDR or a prerecorded CD
UNFINALIZE/ ................when trying to record on a PRESS ENTER finalized CDRW PROF SOURCE ..............when a professional source is
connected
REC TEXT ......................when reading CD text from source
disc for recording
TEXT PROTECT ............when CD text of source disc is
subjected to copy protection (CD text will not be recorded)
Play CHANGER MODE ............CD changer-mode selected DJ MODE ..........................DJ- mode selected when recording
keys are pressed in DJ-mode
PROGRAM..........................program mode selected ALBUM TITLE ..............will be followed by album title TRACK TITLE ..............will be followed by track title ALBUM ARTIST ............will be followed by artist name TRACK ARTIST ............will be followed by track artist
name
Others NO AUDIO TR................when the recorder enters a data
track during recording
FINALIZE CD ..............laser power calibration performed
96 times, finalize disc needed
INITIALIZING ............during laser power calibration for
unfinalized discs
DISC RECOVER ............during disc recovering after power
failure
OPC ERROR ....................OPC failure during OPC procedure
(OPC = Optimum Power Calibration)
RECORD ERROR ............recording error in menu mode DISC ERROR ..................when trying to record on or finalize
a recovered disc
MEMORY FULL/..............when text memory is full. To add a FINALIZE CD CD to the list, first finalize or
erase another disc from the list
NOT POSSIBLE ............when trying to erase a CDR
DISPLAY messages
DISPLAY

Directions for use GB 9CDR779 3.
English
13
This connection is only required if you want to make recordings from an external CD player with a digital coaxial output. Use the digital coaxial cable supplied. 1For external recording, connect the cable 4between the
DIGITAL IN-socket on the CD recorder and the DIGITAL OUT- socket of an external CD player.
Note: Your CD recorder is equipped with a digital coaxial
output (common output for CD recorder & CD player deck). This output can be used for digital playback.
This connection is only required if you want to make recordings from an external CD player with a digital optical output.
When connecting the Digital Optical cable, make sure it is fully inserted until there is a click.
1Remove the dust caps from the digital optical connection.
(We recommend you save the cap.)
For external recording, connect a fibre-optic cable 5
between the digital optical input of the CD recorder and the digital-optical output of an external CD player.
Note: For playback, the digital coaxial outputs or analog
outputs of the CD Player and CD recorder should be connected to an amplifier.
Digital optical connections CD recorderDigital coaxial connections CD recorder
INSTALLATION
English
12 This connection must be made for playback on the CD recorder deck as well as the CD player deck (cable
2
).
Cable
1
is only required if you want to make recordings from
an external analog source. Use the audio cables supplied. Connect the red plugs to the R sockets, and the white plugs to the L sockets. 1For recording, connect cable 1between the ANALOG IN-
sockets on the CD recorder and the CDR LINE- or TAPE OUT- sockets of an amplifier.
Note: For recording directly from a CD player, the analog input
of the CD recorder should be connected to the analog output of the CD player.
For playback, connect cable 2between the ANALOG OUT-
sockets on the CD recorder and the input sockets of an amplifier e.g. TAPE IN, CDR or AUX.
Note: Never use the PHONO input.
This connection is only required if you want to playback on the CD player deck seperately from the CD recorder deck. This will be the case in DJ-mode. 1For separate playback on the CD player deck, connect a
third cable 3(not supplied) between the ANALOG OUT sockets of the CD recorder and the input sockets of an amplifier e.g. CD, or AUX. (Connect the red plugs to the R sockets, and the white plugs to the L socket.)
Note: - Never use the PHONO input. - Your CD recorder/player is equipped with a digital coaxial
output for the CD player deck. This output can be used for digital playback.
Analog connections CD player deckAnalog connections CD recorder & CD player
INSTALLATION

Directions for use
GB 10 CDR7793.
English
15
STANDBY B....................switches to Standby/On SCAN ................................plays the first 10 seconds of each
track
SHUFFLE............................plays CD(RW) or program in
random order
REPEAT..............................repeat play Number/alphabet keys 0 - 9
......................................- selects a track by number
- selects character for text input
TRACK INCR(ement) ........increases track numbers during
recording
SPACE................................inserts a space character during
text input
SCROLL..............................activates scrolling of text over the
display
CDR ....................................selects CD recorder deck CD ......................................selects CD player deck 2......................................starts CD(RW) play O......................................- previous track (Play and Program
mode)
- cursor control in Menu/Prog.
review mode
P......................................- next track (Play and Program
mode)
- cursor control in Menu/Prog.
review mode
9......................................stops CD(RW) and clears a
program
Q....................................searches backward R....................................searches forward ;......................................interrupts CD(RW) play/recording MENU/STORE ..................- enters Menu mode
- stores Menu settings
PROG.(ram) ........................opens/closes program memory ENTER................................- selects settings in Menu mode
- programs track numbers - starts playback of selected track
CANCEL ............................- deletes tracks from a program
- deletes text in Menu mode - returns to a higher level in the
menu
1Press OPEN/CLOSE to open the disc tray.
➜OPEN lights up.
Insert a CD, CDR or CDRW in the appropriate recess in the
tray, label side up.
3Press OPEN/CLOSE to close the tray (see also Playing a CD).
➜CLOSE lights up, followed by READING and the
display will show the type of disc you inserted.
•If you insert a blank or partly-recorded CDR or unfinalized
CDRW, the CD recorder will calibrate the disc for optimum recording. During this process the display will first show INITIALIZING and then the number of audio tracks. Calibration can take up to 25 seconds.
• If a CDR(W) is finalized it will show
CD
on the display.
• If CD-text is available the TITLE/ARTIST will scroll by. Note: - Only Audio CDs will be accepted. If a non-audio disc is
inserted, the display shows
WRONG DISC/
USE AUDIO CD
.
- eading an unfinalized disc in the CD recorder deck could
take approximately 1 minute.
- For recording it is important that the blank disc is completely
free from dust particles or scratches. (see maintenance).
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
ON/OFF
CDR
FINALIZE
OPEN/CLOSEPLAY/PAUSESTOP
REC
TYPERECORD
ERASE
EXT
SOURCE
DIRECT LINE
RECORDING
DOUBLE SPEED
Inserting discs
SCAN
ABC DEF GHI
JKL MN OPQ
RST UVW XYZ
TRACK INCR.
MENU/
STORE PROG.
ENTER CANCEL
CDR
2
9
;
KJ
56
CD
SPACE SCROLL
SHUFFLE REPEAT
123 456
789
0
Remote control commands
REMOTE CONTROL
English
14 1Plug the power cord supplied into the MAINS connector on
the CD recorder, then into a mains socket.
Press ON/OFF.
➜The CD recorder will switch on.
3The recorder switches automatically to active mode. Note: When the CD recorder is in the ‘OFF’ position, it is still
consuming some power. If you wish to disconnect your player completely from the mains, withdraw the plug from the AC outlet.
- Place the CD recorder on a solid, vibration free surface. - Do not place the CD recorder near a source of heat or in
direct sunlight.
- Do not use the CD recorder under extremely damp
conditions.
- If the CD recorder is placed in a cabinet, make sure that a
2.5 cm space remains free on all sides of the CD recorder for proper ventilation.
Important: - Do not put the CD recorder on top of other equipment that
heats up the CD recorder (e.g. receiver or amplifier).
1Open the battery compartment cover. Insert 2 batteries (“AA”, LR-6 or UM-3; as supplied) as
shown.
3Replace the cover. Note: We recommend you use 2 batteries of the same type
and condition.
Batteries contain chemical substances, so they should be disposed of properly.
Inserting batteries in the remote control
Setup recommendations Power supply
INSTALLATION

Directions for use GB 11CDR779 3.
English
17
During high speed recording the sound is not audible. Preparing for high speed recording 1Make sure that the recording disc is absolutely free of
scratches and dust particles.
Press REC TYPE to choose the type of recording
once: to select ‘RECORD FAST’ if you wish to make a
fast recording of a disc or programmed tracks;
three times: to select ‘MAKE CD’ if you wish to make a
fast recording of a disc or programmed tracks and to automatically finalize the recording.
➜The display first shows the selection.
The fRECORDglabel starts blinking. After 3 seconds
the display shows the remaining CDR(W) recording time on the left and total time of source on the right. (every 2 seconds PRESS RECORD is displayed.) The left
selection indicator is lit.
•If DOES NOT FIT appears on the display, there is not
enough recording space left on the CDR(W) disc. You can press RECORD only complete tracks that still fit on the CDR(W) will recorded.
or
You can press PROG to select one or more tracks for recording (see programming) - rotate the EASY JOG/ENTER key to the required track
number, then press the key (or ENTER on the remote control) or
- directly select the track number via the 10-keypad on the
remote control then press the ENTER key to confirm your selection and go to the next step.
Start high speed recording 1Press RECORD to start recording.
➜ WAIT lights up. The display shows the total remaining
time for the selected recording. High speed recording starts. fRECORDglights continuously.
•To check the track number and track time, press DISPLAY.
This can be done during recording.
•Recording will stop automatically. Note: Copy prohibited tracks will be copied analog.
ANALOG
REC
is displayed.
To stop recording manually, press STOP.
➜UPDATE lights up, fRECORDggoes out and
recording stops. (Minimal track length must be 4 seconds otherwise silence will be added to the track.)
•If STOP was pressed within 3 seconds after RECORD, no
recording will take place.
After recording, the display shows UPDATE for several seconds. The Total time indications can differ slightly. However, no music information is lost. Note: In this ecording mode, the Pause function is not
operative.
Important: If you want to play the recorded CDR disc on any regular CD player, it must first be finalized. See finalizing discs. inalized CDRW discs play only on CDRW compatible CD players.
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
OPEN / CLOSE
PLAY / PAUSESTOP
REC
TYPE
OPEN / CLOSE
PLAY / PAUSESTOP
EXT
SOURCE
ERASEFINALIZE
CDR
RECORD
AUDIO CD PLAYBACK
EASY JOGSTORE/
MENU
CANCEL/
DELETE
CD
AUDIO CD PLAYBACK
ENTER
PHONES
AUDIO CD PLAYBACK
DISPLAY SCROLL DJ MODE
REPEAT
SHUFFLE
PROG
CDR 779 AUDIO CD RECORDER
ANALOG
RW
High speed recording from internal CD player
RECORDING
English
16 You will soon discover how easy it is to make your own CDs. Nevertheless, it is advisable to use a CDRW disc for your first try. We will describe
- Recording from internal CD player deck high speed or
listen mode.
- Recording from an external CD player deck syncronized
start with CD player or manual start. (analog or digital).
•If the disc is a CDRW and is already finalized you must
unfinalize it first.
•The recording procedure is the same for CDRs and
CDRWs.
•If the disc already contains recordings, the CD recorder will
automatically search for the end of the last track, so that recording can start from there.
•CD text can be added to a recording in Stop mode and
during recording.
•CD text can not be recorded from an external CD player.
(Text information is not available on the output of the CD player.)
•The CD recorder deck is able to record CD text from the
internal CD player deck. (If not subjected to copy protection.) This may take up to 2 minutes.
•There must be at least 7 seconds of recording time left on
the disc, otherwise you will not be able to enter record standby mode. DISC FULL then lights up.
•If the display indicates COPY PROTECT, no digital
recording can be made of the source material. Recording will not start.
•The Serial Copy Management System (SCMS) only
allows digital recording under specific conditions - This means that it is not possible to make a digital copy
from a digital copy.
- Analog recording is always possible! - The number of recordings from the original is unlimited.
•A maximum of 99 tracks can be recorded on a disc.
Minimum allowable track length is 4 seconds.
•Recordings from DAT or DCC players will not always stop
automatically.
Important: If you want to play the recorded CDR disc on any regular CD player, it must first be finalized. See finalizing discs. inalized CDRW discs play only on CDRW compatible CD players. or recording from CD changers always use
REC EXT
DISC
.
Your recorder offers several recording modes. For recording from internal CD-deck: - ECO D FAST (high speed digital recording) - fast recording
of a disc or programmed tracks.
- EC LISTEN (normal speed digital recording) - listening to a
recording while making it.
- MAKE CD (high speed digital recording and auto-finalize) -
fast recording of a disc or programmed tracks. Recording will be finalized automatically.
Warning: No more recording possible after finalizing CD
disc!
For recording from external sources: - EC EXT DISC (automatic start of recording) - to make an
automatic recording of an external source simply by starting the source.
- EC EXT MAN (manual start of recording) - to start a manual
recording from an external source.
Some remarks on recording: - During high speed recording, the original recording quality
will be maintained.
- When Auto track is on (default setting), track numbers will
automatically be increased during recording.
- By programming tracks first, a compilation can be recorded. - If a finalized CD recordable disc is inserted in the CD
recorder, FINALIZED CD will be displayed when REC TYPE is pressed. Recording is not possible.
- If a finalized CD rewritable disc is inserted in the CD
recorder, UNFINALIZE and PRESS ENTER will be
displayed when the REC TYPE is pressed. If ENTER is pressed, the disc will be unfinalized.
Note: If during recording
ANALOG REC
appears, the track
will be recorded as analog, at normal speed. All other tracks will be copied normally (at double speed).
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
Recording modesRemarks about recording
RECORDING

Directions for use
GB 12 CDR7793.
English
19
Important: - ecording from CD-changers should always be started in the
Auto-Start mode.
- Only make analog recordings when digital recording is not
possible.
Preparing for manual recording 1Make sure the disc is absolutely free of scratches and dust
particles.
Press EXT(ernal) SOURCE repeatedly until (depending on the
connection used) ➜DIGITAL I, OPTICAL I or ANALOG lights up and
DIGITAL 1, OPTICAL or ANALOG appears on the display.
•When Auto Track is On (default setting), track numbers will
automatically be increased during recording.
•To switch off the Auto Track function you have to enter
Menu mode. If you wish to increase track numbers manually, press TRACK INCR(ement) on the remote control. For further instructions see Menu mode.
ON (Auto) The track increments are automatically taken over
from the digital source material or after 2.7 seconds silence during analog recording.
OFF (Manual) While recording track numbers can be
incremented manually by pressing TRACK INCR(ement) on the remote control. (Minimum track length is 4 sec.) (This can also be done in Auto track ON mode.)
• Track numbers cannot be changed after recording. Note: Auto track works only with Consumer Sources with a
digital output signal according to the IEC 958 (consumer part) audio standard.
3With the recorder stopped, press REC TYPE five times to
enter the Manual Record standby mode.
➜Display shows REC EXT MAN followed by WAIT.
After a few seconds PRESS RECORD followed by the remaining time and track number appear on the display.
4Play the source first to set the optimal recording level on
the CD recorder.
5Rotate the EASY JOG/ENTER key until, on the Record/Play
Level bar, all the blue segments are alight, but the red segments do not light continuously during the loudest passages. ➜Display shows _XX DB (Decibel, e.g. -3DB).
6Stop the source. Start manual recording 1To start recording, press RECORD on the CD recorder and
immediately start the source (from Pause or Stop-mode). ➜dlights continuously. The track number and recording
time left appear on the display.
•If CHECK INPUT message also flashes, the digital
connection is incorrect.
•To record a 3-second silence at the start of a track, press
PAUSE on the CD recorder before starting the source.
• To check the total remaining recording time, press DISPLAY on
the CD recorder. (This can also be done during the recording.)
To stop recording, press STOP on the CD recorder.
➜UPDATE lights up and dgoes out.
• If STOP was pressed within 3 seconds after RECORD, no
recording will take place.
• To interrupt recording, press PAUSE on the CD recorder.
dstarts to flash. Press PAUSE again to restart recording. ( A new track will always be made.)
After recording the display will show UPDATE for several seconds. Note: ecordings made analogously will stop after 20 seconds
silence. With
AUTO TRACK OFF
, the auto stop mode is
disabled.
Important: If you want to play the recorded CDR disc on any regular CD player, it must first be finalized. See finalizing discs. inalized CDRW discs play only on CDRW compatible CD players. or recording from CD changers always use
REC EXT
DISC
.
REM TRACK
REC TIME
PROG
SHUFFLE
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TIME STEPTRACK
REM TRACK
REC TIME
PROG
SHUFFLE
CG
SYNC MANUAL RECORD
REMTOTAL
ALL
TIME STEPTRACK
OPEN / CLOSE
PLAY / PAUSESTOP
REC
TYPE
OPEN / CLOSE
PLAY / PAUSE STOP
EXT
SOURCE
ERASE
FINALIZE
CDR
RECORD
AUDIO CD PLAYBACK
EASY JOGSTORE/
MENU
CANCEL/
DELETE
CD
AUDIO CD PLAYBACK
ENTER
PHONES
AUDIO CD PLAYBACK
DISPLAY SCROLL DJ MODE
REPEAT
SHUFFLE
PROG
CDR 779 AUDIO CD RECORDER
ANALOG
RW
Manual recording from external CD player
RECORDING
English
18 During Listen mode recording you listen to the recording while you are making it. Preparing for Listen mode recording 1Make sure that the recording disc is absolutely free of
scratches and dust particles.
For recording, press REC TYPE twice
➜The display first shows the selection.
The fRECORDglabel starts blinking. After 3 seconds
the display shows the remaining CDR(W) recording time on the left and total time of source on the right. (every 2 seconds PRESS RECORD is displayed) The left selection indicator is lit.
•If DOES NOT FIT appears on the display, there is not
enough recording space left on the CDR(W) disc. You can press RECORD only complete tracks that still fit on the CDR(W) will recorded.
or
You can press PROG to select one or more tracks for recording (see programming) - rotate the EASY JOG/ENTER key to the required track
number, then press the key (or ENTER on the remote control)
or
- directly select the track number via the 10-keypad on the
remote control then press the ENTER key to confirm your selection and go to the next step.
3Play the source first to set the optimal recording level on
the CD recorder.
4Rotate the EASY JOG/ENTER key until, on the Record/Play
Level bar, all the blue segments are alight, but the red segments do not light continuously during the loudest passages. ➜Display shows _XX DB (Decibel, e.g. -3DB).
5Stop the source. Start Listen mode recording 1To start recording, press RECORD.
➜ WAIT lights up. fRECORDglights continuously and
the selected track or program is copied at normal speed. The track number and the recording time left will appear.
•To check the track time, press DISPLAY. This can be done
during recording.
•Recording will stop automatically. Note: Copy prohibited tracks will be copied analog.
ANALOG
REC
is displayed.
To stop recording, press STOP.
➜UPDATE lights up, fRECORDggoes out and
recording stops. (Minimal track length must be 4 seconds otherwise silence will be added to the track.)
•If STOP was pressed within 3 seconds after RECORD, no
recording will take place.
After recording, the display shows UPDATE for several seconds. The Total time indications can differ slightly. However, no music information is lost. Note: In this ecording mode, the Pause function is not
operative.
Important: If you want to play the recorded CDR disc on any regular CD player, it must first be finalized. See finalizing discs. inalized CDRW discs play only on CDRW compatible CD players.
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
RECORD
OPEN / CLOSE
PLAY / PAUSESTOP
REC
TYPE
OPEN / CLOSE
PLAY / PAUSESTOP
EXT
SOURCE
ERASEFINALIZE
CDR
RECORD
AUDIO CD PLAYBACK
EASY JOGSTORE/
MENU
CANCEL/
DELETE
CD
AUDIO CD PLAYBACK
ENTER
PHONES
AUDIO CD PLAYBACK
DISPLAY SCROLL DJ MODE
REPEAT
SHUFFLE
PROG
CDR 779 AUDIO CD RECORDER
ANALOG
RW
Listen mode recording from internal CD player
RECORDING

Directions for use GB 13CDR779 3.
English
21
During finalizing the Table of Contents (TOC) is written to the disc. Finalizing is a simple procedure, necessary to - be able to play recordings on a CD PLAYER, - avoid further unwanted recordings on a disc, - avoid erasure of tracks on a CDRW, - write CD text on a CDR(W). Auto finalizing Auto finalizing is possible when using the MAKE CD recording function. Manual finalizing 1Make sure the disc (in the CD recorder deck) is absolutely
free of scratches and dust particles.
With the recorder stopped press FINALIZE.
➜The display shows FINALIZE CD and PRESS
RECORD.
3Press RECORD.
➜ XX XX FINAL and the approximate finalization time
appears on the display. The display counts down through the finalization. On completion, the total number of tracks and the total time recorded appears on the display. For CDR(W), rchanges to don display.
Finalizing will take at least 2 - 4 minutes. Note: - During finalization, the CD recorder accepts no operating
commands.
- When a CD is finalized no more recordings can be added.
For CDRW discs only. If you want to make more recordings (or erasures of tracks) on a finalized disc you must unfinalize it first. The Table of Contents (TOC) will be removed. (This is not possible for CDR discs.) To unfinalize 1With the CD recorder stopped, press REC TYPE or ERASE.
➜UNFINALIZE and PRESS ENTER will appear on
the display.
Press JOG (ENTER).
➜The disc will now be unfinalized and can be recorded on
again and the Recording or Erasure mode is entered.
3You can now start recording or erasing. If no further
recording or erasure is required press STOP 9.
Note: - Unfinalizing will take approximately 1 minute 30 seconds. - When unfinalizing a CD W disc with text on it available,
this text will be transferred to the CD recorder memory. It may occur that the text memory is full. The message
MEMORY FULL
/
FINALIZE CD
will be displayed.
To empty the recorders text memory you have to erase text from it. This can be done in two ways:
1) Finalize one or more unfinalized discs for wich CD text is
available.
2) Delete text of unfinalized discs with the ‘memory view’
option in the Menu mode.
Unfinalizing CDRW discsFinalizing CDR & CDRW discs
RECORDING
English
20 The CD-SYNC feature enables you to make fast and easy recordings of a CD. Track increments are automatically detected from the source material. Track increments cannot be added manually. In analog source material a silence of 2.7 seconds or more is automatically detected as a track increment. Preparing for autostart recording 1Make sure the disc is absolutely free of scratches and dust
particles.
Press EXT(ernal) SOURCE repeatedly until (depending on the
digital connection used) ➜DIGITAL I, OPTICAL I or ANALOG lights up and
DIGITAL 1, OPTICAL or ANALOG appears on the display.
3With the CD recorder stopped, press REC TYPE four times
if you wish to record a complete disc or program. ➜dand
SYNC
start to flash and the display shows REC
EXT DISCand WAIT followed by the track number,
the total remaining time and START SOURCE.
•If input label (DIGITAL I) flashes, the digital connection is
incorrect.
Start autostart recording 1To start recording, press PLAY on the selected source.
➜The CD recorder automatically starts to record and d
and
SYNC
lights continuously. The track number and track
time appear on the display.
•If, however, you start the source during a track, CD-SYNC
recording starts at the beginning of the next track or after 2.7 seconds of silence in analog recordings.
•To check the remaining recording time on the CDR(W), press
DISPLAY. (This can also be done during recording.)
•The EASY JOG/ENTER key can be used to adjust the
recording level.
•The recorder stops automatically. To stop recording manually, press STOP on the CD recorder.
➜UPDATE lights up and
SYNC
and dgo out.
•If STOP 9was pressed within 3 seconds after pressing
PLAY, no recording will take place.
•To interrupt recording, press PAUSE on the CD recorder.
➜dstarts to flash. (Autostart recording is disabled.) To
resume, press RECORD on the CD recorder.
After recording the display will show UPDATE for several seconds. Note: Auto track is always active.
Important: If you want to play the recorded CDR disc on any regular CD player, it must first be finalized. See finalizing discs. inalized CDRW discs play only on CDRW compatible CD players. or recording from CD changers always use
REC EXT
DISC
.
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
OPEN / CLOSE
PLAY / PAUSESTOP
REC
TYPE
OPEN / CLOSE
PLAY / PAUSE STOP
EXT
SOURCE
ERASEFINALIZE
CDR
RECORD
AUDIO CD PLAYBACK
PHONES
AUDIO CD PLAYBACK
DISPLAYSCROLLDJ MODE
REPEAT
SHUFFLE
PROG
CDR 779 AUDIO CD RECORDER
ANALOG
RW
Autostart recording from external CD player CD-SYNC
RECORDING

Directions for use
GB 14 CDR7793.
English
23
Your CD recorder is able to play the two decks sequentially (CHANGER mode). This is the default setting. 1Select Changer mode using the DJ MODE key.
➜CHANGER MODE appears on the display and
iCHANGERhlights up.
On the deck you want to play, press PLAY/PAUSE 2;to
start CD play. ➜2lights up, the track number and track time of the track
in play appear on the display.
➜After playing the first disc the second disc will
automatically be played.
•Press DISPLAY once, twice or three times to see
➜remaining track time, total remaining time, permanent
text information (see Menu mode).
•To interrupt play temporarily, press PLAY/PAUSE 2;again.
➜;lights on the display.
•To continue play, press PLAY/PAUSE 2;again. 3To stop play, press STOP 9.
➜The number of tracks and the total playing time appear
on the display.
•If you want to see the information about the other deck,
press the CDR key or the CD key in the display frame.
With this double deck it is possible to play the CD recorder deck and/or the CD player deck individually (at the same time). In this case the extra CD output must also be connected to an amplifier. 1Select DJ mode using the DJ MODE key.
➜DJ MODE appears on the display and j k lights
up.
On the deck you want to play, press PLAY/PAUSE 2;to
start CD play. ➜2lights up and the track number and track time of the
track in play appear on the display.
•You can also play the two decks at the same time. By
pressing the CDR key or the CD key you can choose the deck you want to listen to.
•Press DISPLAY once, twice or three times to see
➜remaining track time, total remaining time, permanent
text information (see Menu mode).
•To interrupt play temporarily, press PLAY/PAUSE 2;again.
➜;lights on the display.
•To continue play, press PLAY/PAUSE 2;again. 3To stop play, press STOP 9.
➜The number of tracks and the total playing time appear
on the display. If you want to see this information about the other deck, press CDR or CD.
1In stop mode press SCAN on the remote control. The first 10 seconds of each track on the CD (or program if
set) are played.
3Press SCAN again to return to normal CD play mode.
Intro Scan Playing CDs on Deck 1 and/or Deck (DJ mode)Play a -disc changer (Changer mode)
PLAYING
English
22 For unfinalized CDRW discs only. You can erase - Tracks can only be erased from the end. - With the EASY JOG you can erase more tracks.
Note: It is not possible to erase tracks within the sequence.
- It is also possible to erase the entire disc at once. To erase one or more tracks from the end: 1Press ERASE once.
➜The display shows the number of tracks and their total
playing time. ERASE TRACK and PRESS RECORD
lights up.
•If the disc is finalized,
CD
appears on the display after
inserting a CDRW in the recorder. The recorder will ask you to confirm unfinalizing first. Confirm by pressing the EASY JOG/ENTER key or ENTER on the remote control.
Select the track(s) you wish to erase by turning the EASY
JOG/ENTER key to the left. ➜The selected track numbers start blinking on the track
bar.
➜The display shows the remaining time after erasing the
selected track(s), the shown track will also be included in the erasure of tracks.
3Press RECORD.
➜The display shows the total countdown time and
ERASE.
➜After the selected track(s) have erased, the display
shows the remaining tracks and their total playing time.
To erase the entire disc: 1In stop mode press ERASE twice.
➜ERASE DISC and PRESS RECORD light up.
• If the disc is finalized,
CD
appears on the display after
inserting a CDRW in the recorder. The recorder will ask you to confirm unfinalizing first. Confirm by pressing the EASY JOG/ENTER key or ENTER on the remote control.
Press RECORD.
➜The display shows the total countdown time and
ERASE The complete disc will be erased.
Erasure of a complete disc may take up to 15 seconds.
12345678910
12345678910
Erasing CDRW discs
RECORDING

Directions for use GB 15CDR779 3.
English
25
Only in Changer mode. 1Select Changer mode, if nessesary, using the DJ MODE key. Press SHUFFLE before or during CD play to start shuffle
play. ➜The tracks on the CD (or program if set) play in random
order.
3Press SHUFFLE again to disable the Shuffle mode.
➜CD recorder goes to Stop mode.
Note: Shuffle is also cleared if you open the disc tray.
1Press REPEAT one or more times during CD play.
➜When
REPEAT TRACK
lights up, the current track plays
repeatedly. When
REPEAT ALL
lights up, the disc or
program plays repeatedly.
To return to normal play, press REPEAT one or more times
until ➜the
REPEAT
label disappears from the display.
Note: - You can use shuffle in combination with
REPEAT ALL
or
programmed play of the 2-disc changer.
-
REPEAT
is also cleared if you open the disc tray.
Repeat CD, track or programShuffle (random order) play
PLAYING
English
24 Selecting a track during play 1Turn the EASY JOG/ENTER key until the required track
number appears on the display. ➜Play skips to the beginning of the selected track.
or
Select CDR or CD on the remote control and key in the required track number using the numerical keys on the remote control. For 2-digit track numbers, press the keys in rapid succession. For tracks on the other disc, first press CD or CDR as applicable. ➜Play skips to the beginning of the selected track.
or
Press ¡or ™on the remote control one or more times. ➜Play skips to the beginning of the present, previous or
subsequent tracks, including tracks on the disc in the other deck. (Changer mode only.)
Selecting a track when CD play is stopped 1Turn the EASY JOG/ENTER key until the required track
number appears on the display.
Press EASY JOG/ENTER or ENTER on the remote control to
confirm or press PLAY/PAUSE 2;to start playing.
or 1Select CDR or CD on the remote control and key in the
required track number using the numerical keys. For 2-digit track numbers, press the keys in rapid succession. Play starts.
or 1Briefly press ¡or ™one or more times. Start playback by pressing PLAY/PAUSE 2;, EASY
JOG/ENTER or ENTER on the remote control.
1Hold down 5or 6 (in play mode).
➜The player first searches backwards or forwards at 10
times normal speed with sound at low volume, then goes to 50 times normal speed with sound muted.
Release the button at the desired passage.
➜Play starts at the desired passage.
Note: During Shuffle, epeat Track or Programmed play,
search is restricted to within the track being played at the time.
SearchSelecting a track
PLAYING

Directions for use
GB 16 CDR7793.
•In Menu mode you will have access to a number of features
which are not available via the regular keys (on the deck’s front and the remote control).
•The TEXT submenus (A-B) allow you to give names to discs
and tracks. The disc and track names will be displayed during playback.
•In the RECORDING submenus (D-E) you can set Auto Track
and Balance.
•All settings (except Balance) made in Menu mode will be
stored in the deck’s memory and can be called up and changed at any time.
Menu active in Recording or Stop mode. 1When using the remote control select first CDR. Press STORE/MENU on the deck or the remote control to
enter Menu mode. ➜TEXT EDIT appears on the display.
3Rotate EASY JOG/ENTER to select the required submenus. 4Press EASY JOG/ENTER to confirm selections. 5Rotate EASY JOG/ENTER to select options in the submenus. 6Press EASY JOG/ENTER to confirm selections. 7Press STORE/MENU to store settings and return to the
submenu.
8Press STOP 9to store settings and exit Menu mode. Note: Text can only be edited for unfinalized discs. (Finalized
CD W discs must be unfinalized first.)
General operation of MenuRemarks about Menu mode
MENU MODE
English
27
EASY JOGSTORE/
MENU
CANCEL/
DELETE
AUDIO CD PLAYBACK
ENTER
MENU/
STORE PROG.
ENTER CANCEL
CDR
2 9
;
KJ
56
CD
"TITLE CD 1" "TITLE CD 2" "TITLE CD 3" "TITLE CD n" ON OFF
MAIN MENU LEVEL 2LEVEL 1
A B C D E
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
REM TRACK
REC TIME
DIGITAL
OPTICAL
ANALOG
PROG SHUFFLE REPEAT SCAN
I I
CD
RW
CHANGER
SYNC MANUAL RECORD
REMTOTAL
ALL
TRACK
TIME STEPTRACK
CD
RW
123456789
10 11 12 13 14 15 16 17
•You can program up to 99 tracks to play in any desired
sequence.
•Tracks can be programmed more than once, but each time
counts as a track. (
STEP
)
•A program for playback can be made from both the disc in
the recorder deck and the disc in the player deck. A program for recording can only be made from the disc in the player deck.
Programming for playback 1Select Changer mode or DJ mode using the DJ MODE key.
➜CHANGER MODE or DJ MODE appears on the display.
Press CDR or CD to select the required deck.
➜Selected key lights up.
3Press PROG(ram) to enter Program mode.
➜
PROG
flashes and PROGRAM followed by track
information appears on the display.
4Select the required track numbers by turning the EASY
JOG/ENTER key left or right and store by pressing ENTER.
or
Key in a track number with the number keys on the remote control and press ENTER to confirm. For 2-digit numbers, press the keys in rapid succession. ➜The track will be stored in the program. ➜The track number, total program time and the number of
programmed tracks (
STEP
) are displayed.
5Repeat step 4for all tracks to be programmed.
6Press STOP or PROG(ram) to end programming.
➜
PROG
lights continuously.
7Press PLAY/PAUSE 2; to start programmed play.
Note: - To review the program, press P OG(ram), followed by
5
or
6
with the CD player or CD recorder in stop mode.
- To add more tracks to the program, repeat steps 2to 6. - If you try to store more than 99 tracks,
PROG FULL
appears on the display.
Programming for recording 1Press REC TYPE to select the required recording mode (see
‘Recording’).
Compile your programme as described in “programming for
playback”. (steps 3to 5)
•Only tracks from the disc in the CD player can be stored. 3Press RECORD to start recording. Clearing a program 1Press STOP 9if necessary to stop programmed play. Press STOP 9again to clear the program.
➜
PROG
disappears from the display.
•The program is also cleared if you open the disc tray. Erasing a track from a program 1In Stop mode press PROG(ram) to enter Program mode. Use 5or 6to select the track that has to be deleted.
➜The track number and program step will be shown on
the display.
3Press CANCEL/DELETE to erase the track from the program.
➜The remaining program steps and the remaining playing
time of the program will be displayed.
4Repeat step and 3for all tracks to be erased.
5Press STOP 9or PROG(ram) to end erasing.
➜
PROG
lights continuosly.
Remarks about programming
PROGRAMMING
English
26

Directions for use GB 17CDR779 3.
CD Text is stored in the recorders memory. When a CDR(W) will be finalized the CD Text will be written on the disc and removed from the recorders memory. With the MEMORY VIEW function one can view/delete the CD Text in the recorders memory per unfinalized disc. The amount of memory used is displayed each time the tray opens with an unfinalized CDR(W) inserted. (e.g. MEMORY %) 1Press STORE/MENU.
➜TEXT EDIT appears on the display.
Rotate the EASY JOG/ENTER key to select the MEMORY
VIEW submenu. ➜MEMORY VIEW appears on the display.
3Press EASY JOG/ENTER to confirm.
➜The first album title in the recorder memory appears on
the display.
4Select the album title you wish to erase by rotating the
EASY JOG/ENTER key.
5Press EASY JOG/ENTER to confirm.
➜ERASE MEMORY appears on the display.
6Press the EASY JOG/ENTER key to confirm the erasure of
the text for that particular disc. ➜UPDATE appears on the display.
7Press STORE/MENU to return to the submenu or STOP 9to
exit.
Note: - If there are no discs in the memory, the message
MEMORY
EMPTY
appears on the display.
- When the text memory of your CD recorder is full, the
message
MEMORY FULL
will appear, followed by
FINALIZE CD
. If you want to add a CD to the list of
discs for which text is stored, you have to erase a disc from this list or finalize another disc. (“for which text is stored”)
-
MEMORY FULL
/
FINALIZE CD
may also appear when
unfinalizing a CD W disc for which text was stored (see ‘Unfinalizing CD W discs’). The same action(s) should be taken in order to obtain memory space.
MEMORY VIEW
C. Reviewing CD Text in memory/memory view
MENU MODE/CD TEXT
English
29
CD Text can be added to a recording or changed.This can be done in Stop mode or during recording. Text will be stored in the recorder memory and can be edited until the CDR is finalized. Text on a (unfinalized) CDRW can be edited at any time. 1Press STORE/MENU.
➜TEXT EDIT appears on the display.
Press EASY JOG/ENTER to confirm.
➜ALBUM ARTIST appears on the display.
3Rotate EASY JOG/ENTER to select the required option in
the submenu ALBUM ARTIST, ALBUM TITLE,
ARTIST TR 1, TITLE TR 1, etc.
4Press EASY JOG/ENTER to confirm.
➜The first character space appears on the display.
5Select the characters by rotating the EASY JOG/ENTER key
or by pressing the corresponding numeric/alphabet key on the remote control.
6Press EASY JOG/ENTER to store each character and move
to the next cursor position.
• With the 5 6 keys you can move to a required cursor
position.
• With the CANCEL key you can delete a character. 7Press STORE/MENU to store a name you have entered and
return to the submenu resume at 3or STOP 9to exit.
Note: - A maximum of 60 characters can be stored per item. - By pressing the EASY JOG/ENTE key or ENTE on the
remote control without selecting a character first, you can insert a space between characters.
- When an artist’s name has been stored for a certain track,
the name will automatically be copied for the next track. The name can be confirmed by pressing STO E/MENU or a new name can be entered as described above.
1Press STORE/MENU.
➜TEXT EDIT appears on the display.
Rotate the EASY JOG/ENTER key to select the TEXT ERASE
submenu. ➜TEXT ERASE appears on the display.
3Press EASY JOG/ENTER to confirm.
➜If text is available ALL TEXT appears on the display.
(When there is no text available the message NO TEXT appears on the display.)
4Rotate EASY JOG/ENTER to select the required option in
the submenu ALL TEXT, ALBUM ARTIST, ALBUM
TITLE, ARTIST TR 1, TITLE TR 1, etc.
5Press EASY JOG/ENTER to confirm.
➜The display will ask you to reconfirm your selection.
ERASE OK appears on the display.
6Press EASY JOG/ENTER to reconfirm.
➜UPDATE appears on the display.
7Press STORE/MENU to return to the submenu or STOP 9to
exit.
TEXT ERASE ALL TEXT
ALBUM ARTIST ALBUM TITLE ARTIST TR N TITLE TR N NO TEXT
B. Erasing text/text erase
TEXT EDIT ALBUM ARTIST
ALBUM TITLE ARTIST TR N TITLE TR N
A. Text input/text edit
MENU MODE/CD TEXT
English
28

Directions for use
GB 18 CDR7793.
If your CD recorder is defective, it is wise to check this list first. You may have forgotten a simple step. Warning! Under no circumstances should you attempt to repair the CD recorder yourself as this will invalidate the guarantee. SYMPTOM • possible solution No power • ensure that the ON/OFF button is on (red led
on) the CD Recorder is in standby mode, press any key to activate it
• ensure that the mains cable is plugged in
correctly
• switch the recorder OFF and then
immediately back ON
Auto track does not work
• check if auto track on is selected in the menu • check if there are 2.7 seconds silence in
between the tracks (analog recording only)
• check if the source is a consumer source with
the digital output according to the IEC audio standard
• source is DVD player (no track information)
No sound • check the audio connections
• if using an amplifier, try using a different
source
Amplifier sound is distorted
• check that the CD recorder analog output is
not connected to the amplifier Phono input
Play will not start
• ensure that the label of the CD is facing up • clean the disc • check that the disc is not defective by trying
another disc
Remote control does not work
• point the remote control towards the CD
recorder
• check the batteries and replace if necessary • select the correct source first
Will not record
• clean the disc • check if CDR(W) is an unfinalized disc • check that the disc is recordable and replace
if necessary
• the disc is not an AUDIO disc (WRONG
DISC)
• wrong input source chosen. Input label
flashing (CHECK INPUT)
• text memory full (MEMORY FULL/
FINALIZE CD). When a CDRW has to be unfinalized for recording. Erase text for other disc(s) or finalize other disc(s) to obtain memory space
• total remaining time not sufficient, try
programming tracks (see programming)
Recording is distorted
• make sure the recording level is correct
0 second pause between recordings
• see Autostart recording from external CD
player (CD-SYNC)
Player does not react
• switch the ON/OFF button on the front of the
player off and back on
DISC RECOVER on display
• a power failure has occurred during
recording, the CD recorder is attempting to repair the disc
• if DISC ERROR then appears on the
display, the disc cannot be recorded further, and cannot be finalized. But it can still be played on the CD recorder or another CD recorder
• on a CDRW disc, the track being recorded is
lost, but further recording and finalization can still be done
TROUBLESHOOTING
FIXING PROBLEMS
English
31
1Press STORE/MENU.
➜TEXT EDIT appears on the display.
Rotate the EASY JOG/ENTER key to select the AUTO TRACK
submenu. ➜AUTO TRACK appears on the display.
3Press EASY JOG/ENTER to confirm.
➜ON or OFF appears on the display.
4Turn the EASY JOG/ENTER key to select Auto track ON or
OFF.
•When ON is selected, track numbers will be automatically
incremented during recording.
•When OFF is selected, you can number the recorded tracks
yourself.
5Press EASY JOG/ENTER to confirm.
➜AUTO TRACK appears on the display.
6Press STORE/MENU to store settings and return to the
submenu or STOP 9to exit.
1Press STORE/MENU.
➜TEXT EDIT appears on the display.
Rotate the EASY JOG/ENTER key to select the SET
BALANCE submenu. ➜SET BALANCE appears on the display.
3Press EASY JOG/ENTER to confirm.
➜
FE
and L 100 R 100 appear on the display.
4Adjust recording balance by turning the EASY JOG/ENTER
key.
•Turn left the figure left (
F
) counts down, right counts up.
•Turn right the figure right (
E
) counts down, left counts up.
5Press EASY JOG/ENTER to confirm. 6Press STORE/MENU to store settings. Note: The balance setting will not be stored permanently.
SET BALANCE
E. Balance (only active in Record/Standby mode)
AUTO TRACK
ON OFF
D. Auto track increment/auto track
MENU MODE/RECORDING SETTINGS
English
30

Mechanical instructions GB 19CDR779 4.
4. Mechanical instructions
Wiring diagram
8002
3104 157 1105
8002
1 VDC2
2VFTD
3VDC1
4GROUND
5+5V
6+5V
7GROUND
8GROUND
9GROUND
10 +12V
11 -8V
CWAS 11EH/11EH 240 24S
8003
1 VDC2
2VFTD
3VDC1
4 SYS_RESET
5IIC_DATA
6GROUND
7IIC_CLK
8 DISPL_INT
9 GROUND
10 D5V
CWAS 10PH/10EH 440 26S
8004
1 LEFT_HP_OUT
2 GROUND
3 RIGHT_HP_OUT
CWAS 03PH/03PH 440 26S
8001
1 GROUND
2 +12V
3 GROUND
4+5V
5 GROUND
6-8V
7 Doesn't exist
CWAS 06EH/06EH 300 24S
Pin 1 indicated by All Wires are 1/1.
8004
3104 157 11002
8010
3104 157 1148
8003
3104 157 1149
8005
1 GROUND
2 DSA_DATA_CD
3 GROUND
4 DSA_ACK_CD
5 DSA_STR_CD
6 GROUND
7D5V
8 12V_CD
9 GROUND
10 IIS_WS_CD
11 IIS_BCLK_CD
12 GROUND
13 IIS_DATA_CD
14 GROUND
15 DOBM_CD
16 RESET_CD
17 LEFT_IN_CD
18 GROUND
19 RIGHT_IN_CD
20 KILL
21 SYS_CLK_8W
22 GROUND
CWAS FLEX 1mm 22 320 32S
8006
1ON!
2 OFF!
CWAS 02EH/02EH 560 26S
8006
3104 157 1099
8007
1LEFT_CD
2GND
3RIGHT_CD
4GND
5 DOBM_CD
6GROUND
7KILL
CWAS FLEX 1.25mm 7 300 32S
8009
3104 157 03881
Flex
Delivered with loader assy.
Cable
Connected to loader assy.
Flex
Delivered with loader assy.
Cable
Connected to loader assy.
8007
3104 157 1132
8005
3104 157 1123
8008
3104 157 11281
8008
1+5V
2IR_IN
3GROUND
CWAS 03EH/03EH 240 24S
8009
1LED_ON
2GROUND
CWAS 02PH/02PH 120 26S
Flex
Delivered with loader assy.
8001
3104 157 1168
8010
1 GROUND
2OPT_IN
3 DIG_OUT
4 GROUND
5DIG_IN_2
6DIG_IN_1
7 GROUND
8NC.
9 KILL_MAIN
10 DEEMP
11 MUTE
12 MICPRES_INTCOPY
13 LEVEL_A2
14 LEVEL_A1
15 LEVEL_A0
16 GROUND
17 PST3
18 +5Vd
19 IIS_DATA_ADC
20 IIS_BCLK_MIC
21 GROUND
22 IIS_WS_MIC
23 IIS_DATA_DAC
24 GROUND
25 IIS_BCLK_DAC
26 IIS_WS_DAC
27 GROUND
28 MIC_HPSEL
29 CL11_MIC
30 GROUND
CWAS FLEX 0.5mm 30 130
Texture indicates text on flex
3122 427 21573
3104 128 0661
3104 128 06621
3104 128 0648
3104 128 0598
3104 128 0590
3104 128 0590
3104 128 0590
3104 128 0590
1400
1
7
1401
130
11041
3
1101
17
207
205
1
7
1
11
206
1820
1
30 1705 1500 1708
10
1111 1
22
1000
1220
1330
1200
1400
1
3
1302
1300
1119
1122
1121
1
10
1
3
12
1200
1
3
1006
1
11
1002
1001
1
4
1
4
1209
1
7
1208 1
22
1000
130 1
1
1
10
11
4
POWER SUPPLY UNIT
HP
I/O BOARD
MAINBOARD CDR
MAINBOARD CD
HEADPHONE BOARD
DISPLAY BOARD
ON/OFF & STBY LED
IR BOARD
WIRING DIAGRAM CDR779
CL 06532151_001.eps
231100

GB 20CDR779 4.
Mechanical instructions
Wiring CD
Sledge motor
OPU
LOADER VAL1250
CDM VAM1250
Tray motor
MAIN BOARD CD
Turn table
motor
Tray
switch
MAIN BOARD CD
CDM VAM1250
POSITION OF FLEX CONNECTIONS
LOADER VAL1250
Flex from OPU
Flex from
turn table motor
Connector from tray motor
and tray switch
Connector from sledge motor
and sledge switch
Connection tray motor
and tray switch
Connection sledge motor
and sledge switch
Flex from OPU
Flex from
turn table motor
and switch
1002
1208
1210
1209
1001
1006
1000
14
1
22
1
16
1
11
1
16
1
7
14
To main board CDR
To CD out board
CONNECTOR 1006
1 HALL +
2 W-
3 W+
4 V+
5 HALL-
6 U+
7 V-
8 U-
9 UCOIL
10 VCOIL
11 WCOIL
CONNECTOR 1002
1 HOMESW
2 SGND
3 TRAY+
4 TRAY-
CONNECTOR 1001
1 HOMESW
2 SGND
3 SL-
4 SL+
CONNECTOR 1000
1 VSUB
2 HFGND
3 VDD
4 RF
5 LDON
6 R2
7 R1
8 D4/D3
9 D2
10 D1
11 FTC
12 RW
13 FOC+
14 FOC-
15 RAD+
16 RAD-
CONNECTOR 1209
1 AUDIO R (RIGHT_CD)
2 GND
3 AUDIO L (LEFT_CD)
4 GND
5 DOBM5_CD (DOBM_CD)
6 GND
7 KILL
CONNECTOR 1208
1 GND
2 CRIN (SYS_CLK_8W)
3 KILL
4 AUDIO R (RIGHT_IN_CD)
5 GND
6 AUDIO L (LEFT_IN_CD)
7 DSA_RST (SYS_RESET)
8 DOBM (DOBM_CD)
9 GND
10 SCLK (I2S_BCLK_CD)
11 GND
12 WCLK (I2S_WS_CD)
13 DATA (I2S_DATA_CD)
14 GND
15 +12V
16 +5V
17 GND
18 DSA_ACK (DSA_ACK_CD)
19 DSA_STROBE (DSA_STR_CD)
20 GND
21 DSA_DATA (DSA_DATA_CD)
22 GND
WIRING DIAGRAM CD LOADER VAL1250
CL 96532086_002.eps
080999