Philips SRP4319S-27 User manual

User manual
v1 05/20
Home power
SRP4319S/27

2
Introduction ....................................................... 2
Setup .................................................................. 3
Button Functions............................................... 4
Programming Your Remote ..............................6
Direct Code Entry.........................................6
Auto Code Search......................................... 7
Controlling Combo Devices.........................9
Using Your Remote.......................................... 10
Primary Audio Control ............................... 10
Code Identication...................................... 11
Reset to Factory Settings........................... 11
Troubleshooting ...............................................12
Warranty............................................................13
FCC Statement ................................................ 14
Congratulations on your purchase of this
Philips Universal Replacement Remote
Control. Designed primarily for Samsung
devices, this universal remote includes
preprogrammed buttons that allow you
to immediately control your Samsung
equipment. For example, the device buttons
(TV, S-BAR and B-RAY) are preprogrammed to
control a corresponding Samsung TV, sound
bar or Blu-ray™/DVD player. Samsung-specic
function keys (Samsung hub, e-manual,
s.mode, ch.list, etc.) are preprogrammed
for full functionality and navigation of your
Samsung device. Additionally, this remote
is preprogrammed for Roku boxes, using
the STRM button, compatible with all major
brands and capable of operating thousands
of audio/video devices that complete your
home theater setup.
Table of Contents
For remote control help:
byjasco.com/50231i

3
Your universal remote requires two (2) AAA
batteries (not included). Alkaline batteries
are recommended.
Battery Installation
1. On the back of the remote, pull down on
the textured surface and slide battery
cover downward to remove.
2. Match the (+) and (-) marks on the
batteries to the (+) and (-) marks inside
the battery compartment, then insert two
(2) AAA batteries. Be sure to use fresh
batteries.
3. Position battery cover slightly below
opening and push upward to lock into
place.
NOTE:If your remote stops operating properly,
replace the batteries with new ones.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-
zinc), or rechargeable (Ni-Cd, Ni-MH, etc.)
batteries.
• Always remove old, weak or worn-out
batteries promptly and recycle or dispose
of them in accordance with local and
national regulations.
Battery Saver
Your remote automatically turns o if the
buttons are held down for more than 8
seconds. This will save your batteries should
your remote get stuck in a place where the
buttons remain depressed (e.g., between
sofa cushions).
Code Saver
You have up to 10 minutes to change the
batteries in your remote without losing the
codes you have programmed.
Setup

4
Button Functions
CH
10
20
21
25
27
23
29
19
9
5
3
1
7
11
13
4
2
816
812
814
9 1
8
9 22
9 24
9 28
9 26
8
6
15
30
17

5
Button Functions
1. Power - Turns devices ON/OFF
2. Input - Select video inputs
3. TV, B-RAY, S-BAR, STRM - Selects the
device to control
4. Numbers - Enter numbers for direct channel
selection
5. Dash (-) - Use to select digital channels, e.g., 4-1
6. Enter - Some devices require enter to be
pressed after channel selection
7. Mute - Mutes sound
8. Channel up/down
9. Volume up/down
10. Previous channel - Returns to the
previously selected channel
11. Menu - Displays the on-screen menu
12. Home - Access features on streaming devices
Guide - For cable/satellite receivers
13. Samsung hub - Activates Samsung menu
14. Info - Displays on-screen show/content information
15. Tools - Displays frequently used functions on the TV
16. Ok - Selects menu items for the controlled device
17. Up/down/left/right menu navigation
18. Exit -Exit on-screen menus
19. Back - Returns to previous screen
20. ABCD - Access additional features for
DVRs, cable and satellite receivers
21. P.mode - Selects picture mode
22. MTS - Selects stereo, mono or
separate audio program (SAP)
23. S.mode - Selects sound eect options
24. Channel list - Displays list on the screen
25. e-manual - Displays e-manual guide
26. Picture size -Selects picture size
27. Setup - Used to program the remote
28. DVD/Blu-ray™open/close - Open/close a player, or
List features on cable/satellite receivers
29. Closed caption - Selects closed caption options
30. Record, play, stop, rewind, fast forward, pause

6
Programming Your Remote
Your remote is designed to control multiple
audio/video devices. To use, you will need to
program the remote for your devices. There
are two dierent methods you can use to
program the remote, Direct Code Entry or
Auto Code Search.
• The Direct Code Entry method is the
recommended method, as it is the simplest
and quickest method in most cases.
• The Auto Code Search method searches
through all the codes in the remote to nd
a code for your device.
NOTE:This remote comes preprogrammed for
Roku®boxes and Samsung devices. Press TV,
S-BAR and B-RAY for corresponding Samsung
devices, and STRM for Roku boxes.
Direct Code Entry (Recommended)
1. Locate the Code List included
with your remote. Find the
section for the type of device you
wish to control, (e.g., TV, STRM,
DVD, AUD, CBL, AUX). Locate the
brand of your device and circle all
the remote codes for the brand.
2. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
NOTE:The red light will either be a
small light at the top of the remote
or the power ON/OFF button.
3. Press and release the device
button on the remote for the type
of device you wish to control,
(e.g., TV, S-BAR, B-RAY, STRM).
The red light will blink once and
remain on.
NOTE:Any of the device buttons
on the remote can be programmed
to control any of your devices. For
example, you can use the AUD
device button on the remote to

7
Programming Your Remote
control a satellite receiver, digital
converter box, streaming media
player or any device category in
the Code List.
4. Use the number buttons on the
remote to enter the rst 4-digit
remote code you circled in the
Code List in Step 1. The red light
will turn o after entering the
fourth digit.
5. Point the remote at the device.
Test the buttons on the remote
to see if the device responds as
you would expect. If the buttons
do not operate the device,
return to Step 2 above and use
the next code that you circled
for that device.
6. Repeat steps 1 – 5 for each
device you wish to control.
Programming Notes
• Some codes may operate only a few
functions of your device. There may
be another code in the Code List that
controls more functions. Test other codes
in the Code List for more functionality.
• If you do not nd a remote code that
works your device or there are no codes
in the Code List for your device, use the
Auto Code Search method in the next
section to program your remote.
• For combination devices such as a TV/
DVD combo or TV/VCR combo, you may
have to enter a code for each device.
• Write down the remote codes used to
program the remote for future reference.
Auto Code Search
Auto Code Search is a process where you can
search through all the codes stored in the
remote to nd a code for your device. It is
recommended that you read through all the
steps below to familiarize yourself with Auto
Code Search before starting the process.

8
Programming Your Remote
1. Manually turn on the device you
wish to control.
NOTE:The Auto Code Search
process cannot be used for devices
without power ON/OFF capability.
Use the Direct Code Entry method in
these cases.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns
on. Release the SETUP button.
The red light will remain on.
NOTE:The red light will either be a
small light at the top of the remote
or the power ON/OFF button.
3. Press and release the device
button on the remote for the type
of device you wish to control, (e.g.,
TV, S-BAR, B-RAY, STRM). The red
light will blink once and remain on.
4. With the remote pointed at the
device, press and release the
POWER button on the remote.
The remote will send 10 dierent
codes to the device. The red light
will blink once for each code and
remain on after sending the 10
codes.
Did the device turn o?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the
next 10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the
device, press and release the
VOL button. The remote will re-
send the rst code of the 10 codes
from Step 4. The red light will blink
once and remain on.
Did the device turn o?
• If YES, you have found a code
for the device. Press and
release the same device button
you pressed in Step 3. This will

9
Programming Your Remote
store the code in the remote.
Go to Step 7.
• If NO, continue to press and
release the VOL button
until the device turns o
to test the other 9 codes
from Step 4. Be sure to wait
approximately 3 seconds after
each VOL button press
to allow the device time to
respond to the code. When
the device turns o, you have
found a code for your device.
Press and release the same
device button pressed in Step
3. This will store the code in
the remote. Go to Step 7.
NOTE:
• The VOL button can be used
to go backwards through each
batch of 10 codes.
• The red indicator light will ash
2 times after testing the rst or
last code in each batch of 10.
7. Use the remote to turn the
device back on. Test the buttons
on the remote to see if the
device responds as you would
expect. If the buttons do not
operate the device, return to
Step 2 and repeat this process
to search for a better code to
operate the device.
8. Repeat this process for each
device you wish to control.
Controlling Combo Devices
Some combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up
two dierent device buttons to control both
parts of the combo device. For example, if
you have a TV/DVD combo, you may need
to set up one code under the TV button to
control the TV and a separate code under
the DVD button to control the DVD.

10
Using Your Remote
Primary Audio Control
The Primary Audio Control feature allows
you to select a single device that the volume
buttons always control. For example, the
remote can be in TV mode while the volume
buttons control the volume on your audio
receiver or sound bar instead of your TV.
Enabling Primary Audio Control
1. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
2. Press and release the device
button (TV, S-BAR, etc.) on the
remote for the device you wish
to control the volume.
3. Press and release the
MUTE button.
4. Press and release the VOL
button. The red light will blink
twice and turn o.
Disabling Primary Audio Control
1. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
2. Press and release the device
button (TV, S-BAR, etc.)
programmed to control the
Primary Audio Control feature.
3. Press and release the
MUTE button.
4. Press and release the VOL
button. The red light will blink
twice and turn o.