Philips WE Series User manual

WE Series
Industrial/Harsh Environment Emergency Lighting
Page 1 of 2
Job Information Type:
Job Name:
Cat. No.:
Notes:
Features
Illumination: Illumination
is accomplished with lamp
heads externally or internally
mounted. The standard unit
with external heads includes
Lightolier’s “IT” series 6 or
12 V lamp head in a variety of
wattages. Units with internal
heads may use the 5.4 W, 7 W,
or 9 W, 6 V lamp heads.
Optional lamp heads may be
selected for external mounting
only.
Housing: Constructed of
impact-resistant, fiberglass-
reinforced polyester. Housing
color is gray. Includes
two black, rectangular
thermoplastic 9 W lamp heads
externally mounted. Internally
mounted white or black lamp
heads available with “IH”
option (up to 25 W units only.)
One-piece, molded gasket and
unexposed metallic hardware
prolong product life in highly
corrosive areas.
Operating Temperature
Range: Standard Location
65°F (19°C) to 85°F (30°C)
Damp/Wet Location
50°F (10°C) to 104°F (40°C)
Electronics: 120/277 VAC
dual voltage input with surge-
protected, solid-state circuitry
provides for a reliable charging
system. Charging system is
complete with low voltage
disconnect, AC lockout,
brownout protection, AC
indicator lamp and test switch.
Electrical Specifications:
0.15 A, 18 W (120 VAC)
0.07 A, 18 W (277 VAC)
Code Compliance
UL 924 and optional UL wet
and damp location listed. NFPA
101, NEC, BOCA, OSHA and
IBC illumination standards.
NSF standard 2 “Splash Zone”.
Warranty
Three year full electronics
warranty. One year full plus
four year prorated lead calcium
battery warranty. Five year full
plus five year prorated nickel
cadmium battery warranty.
WE118L2IT8
12.0"
(30.5 cm)
12.1"
(30.7 cm)
6.5"
(16.5 cm)
With internal lamp heads (IH) option.
6.5"
(16.5 cm)
12.0"
(30.5 cm)
7.1"
(18.0 cm)

WE Series
Industrial/Harsh Environment Emergency Lighting
Page 2 of 2
Philips Lightolier
e: [email protected]
t: [phone]
w: www.lightolier.com
WE Series May 3, 2012
Specifications are subject to change without notice.
© Koninklijke Philips Electronics N.V., 2012.All rights reserved.
Job Information Type:
Ordering Information
Series
WE = NEMA Rated
Wet Location Listed
Emergency Lighting
1= 6 V
2= 12 V
Voltage
6 V, Lead Calcium
18L = 18 W
25L = 25 W
36L = 36 W
50L = 50 W
6 V, Nickel Calcium
14N = 14 W3
18N = 18 W
25N = 25 W
50N = 50 W
Battery/DC Wattage
EX = Special Input Transformer1
(specify voltage & frequency)
T1 = 120 VAC Time Delay2
T2 = 277 VAC Time Delay2
TP = Tamperproof
W= UL Wet Location Listing
Z= UL Damp Location Listing
IH = Internally Mounted Lamp Heads
(specify head type below**, up to 25 W units only)
Factory Installed Options1
Accessories (order as a separate item)
EMF = External Mounting Feet
NTPTOOL = Tamperproof Screwdriver
PCS1 = Polycarbonate Vandal Shield
WG5 = Wire Guard for Back Mount Units
Note
1) Some option combinations may impact UL listing. Consult factory for specifics.
2) 15 minute delay.
3) Standard lamp head 7 W, 6 VDC.
WE
12 V, Lead Calcium
36L = 36 W
50L = 50 W
12 V, Nickel Calcium
50N = 50 W
Blank = No
Heads
1= One
2= Two
# of Heads
6 V
IT8 = 8 W
IT18 = 18 W
IT25 = 25 W
12 V
IT12 = 12 W
IT18 = 18 W
IT25 = 25 W
Lamp Heads
White
S66 = 6 V, 5.4 W
S76 = 6 V, 7 W
S96 = 6 V, 9 W
Black
S66B = 6 V, 5.4 W
S76B = 6 V, 7 W
S96B = 6 V, 9 W
**Internal heads only available with "S" type heads.
Wall mounted 7.5' AFF, ‘S96’ 6 V 9 W Tungsten Lamps Represented
7.5 ft.
25 ft.
6 ft.
Average initial footcandles at floor = 1.08
Maximum initial footcandles at floor = 3.0
Minimum initial footcandles at floor = 0.3
Maximum to minimum ratio = 10.00
0.3
0.3
0.2
1.2
1.1
0.4
2.4
2.3
0.7
2.3
1.8
0.6
1.6
1.0
0.4
0.9
0.6
0.4
0.7
0.6
0.5
0.9
0.6
0.4
1.4
0.8
0.4
2.3
1.5
0.5
2.6
2.4
0.8
1.6
1.7
0.9
.5
0.5
0.3
0.7
0.7
0.4
2.0
1.9
0.6
2.6
2.2
0.7
2.0
1.3
0.4
1.2
0.7
0.4
0.8
0.6
0.4
0.7
0.6
0.4
1.1
0.6
0.4
1.8
1.1
0.4
2.5
2.0
0.6
2.2
2.2
0.7
0.8
0.9
0.4
0.2
0.3
0.2
1 FC Average
Optics
* The optics layout shown is intended to be used as reference only. Standard reflectances used were 80/50/20. Lightolier is not responsible for site specific conditions that
may alter the results.