Phoenix Contact TP 3043W User manual

Touch Panels with TFT-Display
User manual

PHOENIX CONTACT 106358_en_02
User manual
Touch Panels with TFT-Display
2018-02-21
Designation:
Revision:
Order No.:
UM EN TP 3XXXX GEN3
02
—
This user manual is valid for:
Designation Order No.
TP 3043W
TP 3057Q
TP 3057V
TP 3070W
TP 3090W
TP 3105S
TP 3121S
TP 3120W
TP 3150S
TP 3154W
2402629
2400452
2400453
2400454
2402630
2400455
2400456
2400457
2400458
2402631

PHOENIX CONTACT
How to contact us
Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be
found on the Internet at:
phoenixcontact.com
Make sure you always use the latest documentation.
It can be downloaded at:
phoenixcontact.net/products
Subsidiaries If there are any problems that cannot be solved using the documentation, please contact
your Phoenix Contact subsidiary.
Subsidiary contact information is available at phoenixcontact.com.
Published by PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
GERMANY
Should you have any suggestions or recommendations for improvement of the contents and
layout of our manuals, please send your comments to
[e-mail]

TP 3XXXX GEN3
PHOENIX CONTACT
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical documen-
tation and the products described in the technical documentation at its own discretion and
without giving prior notice, insofar as this is reasonable for the user. The same applies to any
technical changes that serve the purpose of technical progress.
The receipt of technical documentation (in particular user documentation) does not consti-
tute any further duty on the part of Phoenix Contact to furnish information on modifications
to products and/or technical documentation. You are responsible to verify the suitability and
intended use of the products in your specific application, in particular with regard to observ-
ing the applicable standards and regulations. All information made available in the technical
data is supplied without any accompanying guarantee, whether expressly mentioned, im-
plied or tacitly assumed.
In general, the provisions of the current standard Terms and Conditions of Phoenix Contact
apply exclusively, in particular as concerns any warranty liability.
This manual, including all illustrations contained herein, is copyright protected. Any
changes to the contents or the publication of extracts of this document is prohibited.
Phoenix Contact reserves the right to register its own intellectual property rights for the prod-
uct identifications of Phoenix Contact products that are used here. Registration of such in-
tellectual property rights by third parties is prohibited.
Other product identifications may be afforded legal protection, even where they may not be
indicated as such.

Table of Contents
106358_en_02 PHOENIX CONTACT 5
Table of Contents
1 Important Notes .........................................................................................................................7
1.1 Symbols ................................................................................................................ 7
1.2 Safety Notes.......................................................................................................... 7
1.3 Intended Use ......................................................................................................... 8
1.4 Target Group ......................................................................................................... 8
2 Installation and Commissioning .................................................................................................9
2.1 Unpacking the Device............................................................................................ 9
2.2 Mounting the Device............................................................................................ 10
2.2.1 Front Panel Dimensions ....................................................................... 11
2.2.2 Mounting Cutout .................................................................................. 21
2.2.3 Side View, Mounting Depth .................................................................. 31
2.3 Connecting the Device ........................................................................................ 41
2.3.1 Supply Voltage ..................................................................................... 41
2.3.2 Grounding ............................................................................................ 42
2.4 Switching On ....................................................................................................... 43
2.5 Identification ........................................................................................................ 43
3 Control and Display Elements ..................................................................................................45
3.1 Touchscreen ....................................................................................................... 45
3.2 Display................................................................................................................. 45
4 Interfaces of the Device ...........................................................................................................47
4.1 Standard Interfaces ............................................................................................. 47
4.1.1 Ethernet (X5) ........................................................................................ 48
4.1.2 USB (X9, X10) ..................................................................................... 49
4.1.3 Memory Card ....................................................................................... 50
4.2 Serial Interfaces................................................................................................... 51
4.2.1 RS-422 / RS-485 (X14) ........................................................................ 52
4.2.2 RS232 (X15) ........................................................................................ 55
4.3 Shielding D-SUB Connectors .............................................................................. 56
5 Maintenance and Servicing ......................................................................................................57
5.1 Maintenance Interval ........................................................................................... 57
5.2 Front Panel .......................................................................................................... 57
5.3 Fuse .................................................................................................................... 57
5.4 Battery................................................................................................................. 57

TP 3XXXX GEN3
6PHOENIX CONTACT 106358_en_02
6 Technical Data .........................................................................................................................59
6.1 General................................................................................................................ 59
6.2 TP 3043W ........................................................................................................... 61
6.3 TP 3057Q ............................................................................................................ 62
6.4 TP 3057V............................................................................................................. 63
6.5 TP 3070W ........................................................................................................... 64
6.6 TP 3090W ........................................................................................................... 65
6.7 TP 3105S............................................................................................................. 66
6.8 TP 3121S............................................................................................................. 67
6.9 TP 3120W ........................................................................................................... 68
6.10 TP 3150S............................................................................................................. 69
6.11 TP 3154W ........................................................................................................... 70

Important Notes
106358_en_02 PHOENIX CONTACT 7
1 Important Notes
1.1 Symbols
The symbols in this manual are used to draw your attention on notes and dangers.
There are three signal words indicating the severity of a potential injury.
1.2 Safety Notes
– Read this manual carefully before using the operating device. Keep this manual in a
place where it is always accessible to all users.
– Proper transportation, handling and storage, placement and installation of this product
are prerequisites for its subsequent flawless and safe operation.
– This user manual contains the most important information for the safe operation of the
device.
– The user manual, in particular the safety notes, must be observed by all personnel
working with the device.
– Observe the accident prevention rules and regulations that apply to the operating site.
– Installation and operation must only be carried out by qualified and trained personnel.
This symbol indicates hazards that could lead to personal injury.
DANGER
Indicates a hazard with a high risk level. If this hazardous situation is not avoided, it will
result in death or serious injury.
WARNING
Indicates a hazard with a medium risk level. If this hazardous situation is not avoided, it
could result in death or serious injury.
CAUTION
Indicates a hazard with a low risk level. If this hazardous situation is not avoided, it could
result in minor or moderate injury.
This symbol together with the NOTE signal word alerts the reader to a situation which may
cause damage or malfunction to the device, hardware/software, or surrounding property.
Here you will find additional information or detailed sources of information.

TP 3XXXX GEN3
8PHOENIX CONTACT 106358_en_02
1.3 Intended Use
– The device is designed for use in the industry.
– The device is state-of-the art and has been built to the latest standard safety require-
ments. However, dangerous situations or damage to the machine itself or other prop-
erty can arise from the use of this device.
– The device fulfills the requirements of the EMC directives and harmonized European
standards. Any modifications to the system can influence the EMC behavior.
1.4 Target Group
The use of products described in this manual is oriented exclusively to:
– Qualified electricians or persons instructed by them. The users must be familiar with the
relevant safety concepts of automation technology as well as applicable standards and
other regulations.
– Qualified application programmers and software engineers. The users must be familiar
with the relevant safety concepts of automation technology as well as applicable stan-
dards and other regulations.
NOTICE: Radio Interference
This is a class A device. This device may cause radio interference in residential areas. In
this case, the user may be required to introduce appropriate countermeasures, and to
bear the cost of same.

Installation and Commissioning
106358_en_02 PHOENIX CONTACT 9
2 Installation and Commissioning
2.1 Unpacking the Device
Unpack all parts carefully and check the contents for any visible damage in transit. Also
check whether the shipment matches the specifications on your delivery note.
If you notice damages in transit or discrepancies, please contact us immediately.

TP 3XXXX GEN3
10 PHOENIX CONTACT 106358_en_02
2.2 Mounting the Device
The device can be easily and quickly mounted from the rear of the device. A panel thickness
of 1 mm to 6 mm (0.039" to 0.236") is permitted for proper mounting.
1. Cut the mounting cutout in the housing for the device size to be installed.
2. Push the device through the mounting cutout from the front.
Figure 2-1 Mounting the device using a mounting bracket
3. Fix the mounting brackets in the recesses provided (A).
4. Pull the mounting brackets down until the snap into place (B).
5. Secure the device using the threaded pins (C).
NOTICE: Damage
When installing the device, leave a gap of at least 30 mm (1.181") around the device to
ensure sufficient air circulation.
NOTICE: Damage
When the operating device is installed horizontally, please note that additional sources of
heat beneath the operating device may result in heat accumulation.
Make sure to allow sufficient heat dissipation!
Please observe the permissible temperature range specified in the technical data when
operating the device.
NOTICE: Damage
In order to ensure the degree of protection specified in the technical data, observe the fol-
lowing points:
– A tolerance of ±0.5 mm is maintained for the mounting cutout.
– The seal lies flat against the mounting surface.
– The number of mounting brackets, given in the technical data, is used.
– The threaded pins of the mounting brackets are tightened uniformly to a maximum
torque of 1 Nm.
C
B
A

Installation and Commissioning
106358_en_02 PHOENIX CONTACT 11
2.2.1 Front Panel Dimensions
2.2.1.1 TP 3043W
Figure 2-2 Front panel (dimensions in mm)
140
100

TP 3XXXX GEN3
12 PHOENIX CONTACT 106358_en_02
2.2.1.2 TP 3057Q
Figure 2-3 Front panel (dimensions in mm)
147
203

Installation and Commissioning
106358_en_02 PHOENIX CONTACT 13
2.2.1.3 TP 3057V
Figure 2-4 Front panel (dimensions in mm)
168
126

TP 3XXXX GEN3
14 PHOENIX CONTACT 106358_en_02
2.2.1.4 TP 3070W
Figure 2-5 Front panel (dimensions in mm)
203
147

Installation and Commissioning
106358_en_02 PHOENIX CONTACT 15
2.2.1.5 TP 3090W
Figure 2-6 Front panel (dimensions in mm)
172
260

TP 3XXXX GEN3
16 PHOENIX CONTACT 106358_en_02
2.2.1.6 TP 3105S
Figure 2-7 Front panel (dimensions in mm)
295
220

Installation and Commissioning
106358_en_02 PHOENIX CONTACT 17
2.2.1.7 TP 3121S
Figure 2-8 Front panel (dimensions in mm)
270
340

TP 3XXXX GEN3
18 PHOENIX CONTACT 106358_en_02
2.2.1.8 TP 3120W
Figure 2-9 Front panel (dimensions in mm)
330
225

Installation and Commissioning
106358_en_02 PHOENIX CONTACT 19
2.2.1.9 TP 3150S
Figure 2-10 Front panel (dimensions in mm)
329
400

TP 3XXXX GEN3
20 PHOENIX CONTACT 106358_en_02
2.2.1.10 TP 3154W
Figure 2-11 Front panel (dimensions in mm)
420
297