Phoenix Model CLASSIC-EP User manual

Instruction Manual
CLASSIC - EP
Wingspan: 1420mm (55.9 inch)
Length : 1070mm (42.1 inch)
Weight : 1700gr - 2000gr
Engine : AXI motor 2826
Radio : 4 channel / 3 servos standard
g

KIT CONTENTS: We have organized the parts as they come out of the box for better identification
during assembly. We recommend that you regroup the parts in the same manner. This will ensure you
have all of parts required before you begin assembly
KIT CONTENTS
AIR FRAME ASSEMBLIES
(2) Wing
(1) Fuselage
(1) Horizontal
(1) Vertical
(1) Instruction manual
main gear assembly
(2) Main gear
(2) 60mm wheel
(4) Collar
(4) 3mm x 4mm screw
(2) Nylon clasp
(4) 3mm x 12mm screw
nose gear assembly
(1) Nose gear
(1) 60mm wheel
(2) Collar
(2) 3mm x 4mm screw
(1) Steering arm
elevator control system
(1) Clevis
(1) Silicon tube
(1) Nylon clasp
(1) Nylon control horn
(2) 2mm x 16mm screw
(1) 1,7mm x 900mm metal rod
rudder control system
(1) Clevis
(1) Silicon tube
(1) Nylon clasp
(1) Nylon control horn
(2) 2mm x 16mm screw
(1) 1,7mm x 900mm metal rod
aileron control horn
(2) Clevis
(2) Silicon tube
(2) Nylon control horn
(2) Nylon snap keeper
(2) 1,7mm x 300mm metal rod
engine mount
(4) 3mm x 12mm screw
(4) Lock washer
(1) Wooden engine mount
miscellaneous items
(1) Dihedral
(1) Trim tape 25mm x 600mm
(8) Rubber band
(2) 12mm dowel
(2) Plate of wood
(1) Metal connector
(1) Servo box
1

2
1 2
3 4
5 6
7 8
Draw a center line. Remove the covering.
Glue the wing joiner to the wing. Apply the epoxy into the wing section.
Glue the wing by epoxy. Apply the trim tape to the center section on the top and the
bottom of the wing where they join.
Glue the two hard wood by C.A glue. Mark the shape of the servo box to the wing.
I
nstalling the wing halves
.
Installing the wing halves.
1
Installin
g
the aileron servo and linka
g
e.
Installing the aileron servo and linkage.
2
Center line

3
910
11 12
13 14
15 16
Remove the covering. Glue the servo box by C.A glue.
Install and secure the aileron servo. Install the two nylon control horn.
Install the clevis to the aileron pushrod. Insert the silicon tube into the clevis.
Insert the clevis into the control horn. Cut away and bend "L" the aileron pushrod.
Hard wood
Servo box
Control horn
Clevis

4
17 18
19 20
21 22
23 24
Attach the nylon clasp to the aileron servo arm. Make the same way for the second aileron pushrod.
Make a center line onto the horizontal. Remove the covering from the fuselage.
Attach the horizontal to the fuselage and check it. Mark the shape of the fuselage onto the top of the horizontal.
Mark the shape of the fuselage onto the bottom of the
horizontal.
Remove the covering from the top and the bottom of the
horizontal.
Installing the horizontal and vertical stabilizer.
3
Nylon clasp

5
25 26
27 28
29 30
31 32
Check the horizontal before it dry and remove the wing
out of the fuselage.
Glue the horizontal and fuselage by epoxy.
Glue the horizontal and fuselage by epoxy. Cut away the covering from the fuselage.
Mark the shape of the fuselage onto the both side of the
vertical.
Remove the covering from the vertical.
Remove the covering on the top of the fuselage. Glue the vertical into the fuselage by epoxy.
Remove
the covering

6
33
34 35
36 37
38 39
Check the fin before it dry and remove the wing out of the
fuselage.
The elevator and rudder linkages. Secure the control horn onto the elevator.
Cut away the screw. Remove the covering from the slot.
Install the clevis to the aileron pushrod. Insert the silicon tube into the clevis.
a1 a2
a1 = a2
Install
i
n
g
the elevator
p
ushrod
.
Installing the elevator pushrod.
4

7
40 41
42 43
44 45
46 47
Insert the elevator pushrod into the fuselage. Attach the clevis to the control horn.
Install the elevator servo. Cut away the elevator pushrod.
Bend "L" the elevator pushrod. Attach the nylon clasp to the servo arm.
Install the rudder control horn. Cut away the screw.
Installing the rudder pushrod
.
Installing the rudder pushrod.
5

8
48 49
50 51
52 53
54 55
Remove the covering from the slot. Insert the rudder purshrod into the fuselage.
Attach the clevsis to the control horn. Install the rudder servo.
Install the metal connector to the servo arm. Install the servor arm into the rudder servo.
Cut away the rudder pushrod. Bend "L" the rudder pushrod.

9
56
57 58
59 60
61 62
Attach the nylon clasp to the servo arm.
The landing gear and nose gear. Install the collar.
Install the wheel. Cut away the covering from the fuselage.
Install the landing gear. Secure the landing gear.
I
nstall
i
n
g
the land
i
n
g
g
ear and nose
g
ear.
Installing the landing gear and nose gear.
6
Collar
Gear
Collar