Phoenix Model Tiger 3 User manual

Wingspan : 1500mm (59.2 inch)
Length : 1250mm (49.2 inch)
Weight : 2400gr - 2600gr
Engine : 40 - 46 two stroke / 52 four stroke
Radio : 4 channel / 4 servos standard
g
We wish you many enjoyable flights with your plane and one again thank you for your choosing a Phoenix Model products.
Instruction Manual
ua
ru
nstruction Manual
l
Instruction Manu
ction Man
nst
uc
tion Manua
l
ion Manu
Instruction M
HOBBIRAN.COM

KIT CONTENTS: We have organized the parts as they come out of the box for better identification
during assembly. We recommend that you regroup the parts in the same manner. This will ensure you
have all of parts required before you begin assembly
AIR FRAME ASSEMBLIES
(2) Wing
(1) Fuselage
(1) Horizontal
(1) Vertical
(1) Instruction manual
main gear assembly
(2) Main gear
(2) 60mm wheel
(4) Collar
(4) 3mm x 4mm screw
(4) Nylon clasp
(8) 3mm x 12mm screw
nose gear assembly
(1) Nose gear
(1) 60mm wheel
(2) Collar
(2) 3mm x 4mm screw
(1) Steering arm
elevator control system
(1) Clevis
(1) Nylon clasp
(1) Nylon control horn
(2) 2mm x 16mm screw
rudder control system
(1) Clevis
(1) Nylon clasp
(1) Nylon control horn
(2) 2mm x 16mm screw
aileron control horn
(2) Clevis
(2) Nylon clasp
(2) Nylon control horn
(2) 2mm x 180mm wire metal pushrod
engine mount
(4) 3mm x 20mm screw
(4) Lock washer
FUel TANK
(1) Fuel tank
(1) Clunk
(1) 110mm silicone tube
(1) Stopper
(1) 160mm x 250mm foam
miscellaneous items
(1) Dihedral
(1) Spinner
(1) Trim tape 25mm x 600mm
(2) 4mm x 30mm screw
(2) Washer
(2) Metal connector
(1) Servo box
KIT CONTENTS
tiger 3
Instruction Manual
1

2
1 2
3 4
5 6
7 8
Draw a center line. Remove the covering.
Glue the wing joiner to the wing, using the epoxy glue. Apply the epoxy into the wing section.
Glue the wing by epoxy. Apply the trim tape to the center section on the top and the
bottom of the wing where they join.
Servo box. Glue the two hard wood by C.A glue.
tiger 3
Instruction Manual
1. Joining the wing halves.
2. Installing the aileron servo and linkage.
Center line
HOBBIRAN.COM

3
910
11 12
13 14
15 16
Mark the shape of the servo box to the wing. Remove the covering.
Glue the servo box by C.A glue. Install and secure the aileron servo.
Install the two nylon control horn. Install the clevis to the aileron pushrod.
Attach the clevis to the control horn. Cut away the aileron pushrod.
tiger 3
Instruction Manual
Nylon control horn
Clevis
Control horn
Metal pushrod Clevis
Hard wood
Servo box
HOBBIRAN.COM

4
17 18
19 20
21 22
23 24
Bend "L" the aileron pushrod. Attach the nylon clasp to the aileron servo arm.
The landing gear. Remove the covering from the bottom of the wing.
Drill four holes for the nylon straps. Install the collar.
Install the wheel. Install and secure the landing gear.
tiger 3
Instruction Manual
3. Installing the landing gear and nose gear.
Nylon clasp
Collar
Gear
Collar
Nylon strap

5
25 26
27
28 29
30 31
The nose gear. Install the wheel.
Install the nose gear.
Draw a center line. Remove the covering from the fuselage.
Attach the horizontal to the fuselage and check it. Mark the shape of the fuselage onto the bottom of the
horizontal.
tiger 3
Instruction Manual
4. Installing the horizontal and vertical stabilizer.

6
32 33
34 35
36 37
38 39
Remove the covering from the bottom of the horizontal. Glue the horizontal and fuselage by epoxy.
Cut away the covering from the fuselage. Mark the shape of the fuselage onto the both side of the
vertical.
Remove the covering from the vertical. Remove the covering on the top of the fuselage.
Glue the vertical into the fuselage by epoxy. Finishing.
tiger 3
Instruction Manual

7
40 41
42 43
44 45
46 47
The control horn. Install the control horn onto the elevator.
Remove the covering from the slot. Attach the clevis to the elevator pushrod.
Attach the clevis to the control horn. Install the nylon control horn.
Remove the covering. Attach the clevis to the rudder pushrod.
tiger 3
Instruction Manual
5. Installing the elevator and rudder pushrod.
Control horn
Clevis
Control horn
Clevis
Pushrod

8
48 49
50 51
52 53
54 55
Attach the clevis to the control horn. Install the rudder servo.
Install the metal connector. Connect the rudder pushrod and the nose gear pushrod to
the rudder servo.
Cut away the rudder pushrod. Bend "L" the rudder pushrod.
Attach the nylon clasp to the servo arm. Install the elevator servo.
tiger 3
Instruction Manual
HOBBIRAN.COM

9
56 57
58 59
60 61
62 63
Cut away the elevator pushrod. Bend "L" the elevator pushrod and attach the nylon clasp.
The stopper. Install the stopper to the tank.
Secure the stopper. Install the silicone tube to the tank.
Slide the fuel tank into the fuselage. Secure the fuel tank by foam and wood.
tiger 3
Instruction Manual
6. Installing the fuel tank.
Wood
C.A glue