Phonak iCom User manual

029-0695-02/V3.00/2010-03/A+W Printed in Switzerland © Phonak AG All rights reserved
www.phonak.com
Blue, short flash
= 2 phones connected
Blue, solid
= Bluetooth transmission
(music or call)
To check the version of your iCom press the
ON/OFF Button once in standby mode.
Yellow, 3 flashes
= iCom version 3
offers 2 phone support, voice
dialing, last number redial and
audio lock.
Please ask your hearing care professional for
further help.
For your safety, please read the iCom user guide
carefully. Pay particular attention to the “Important
information” section and the following symbol
which refers to associated warnings.
Light indicator (for details refer to the user guide)
Red, one flash
= iCom switching off
Green
= iCom switch on
Yellow, interrupted solid
=Audio transmission
locked in
Yellow, solid
= Audio transmission
Yellow, medium flash
= Audio transmission pause
Blue, medium flash
= 1 phone connected or
Bluetooth audio paused
iCom Quick Guide and features
!
0682 !
Main Button
Voice dial
press 2 seconds
Last number redial
press 2x short
Pick up or end call, accept FM signal
short press
Refuse incoming call
press 2 seconds
ON/OFF Button
press 2 seconds
Quick Guide and Features
Using audio devices and FM
Connecting Connecting
via audio cable via an FM system
쐍To pause/restart transmission of audio inputs
from any source press the Main Button
쐍To stop audio, turn off audio source or
unplug audio cable
쐍To stop FM, switch off FM or unplug the
FM receiver from iCom
If the signal transmission through audio cable or FM
system is not stable, short press the ON/OFF Button
during transmission to “lock” the audio program.
AUDIO
3.5 mm stereo jack

Charging the iCom battery
You can continue to use iCom while it is charging.
Turning your iCom
on and off
press for
2 seconds
Getting started
Setting up Bluetooth devices
Before you start using your iCom with Bluetooth
devices you need to pair the devices. Please refer to
the main user guide for instructions. Pairing code
is “0000”.
sing iCom with one or two mobile phones
쐍You can connect up to two phones at the
same time with iCom
쐍Each phone has its own fixed ringtone
쐍To accept an incoming phone call, press the
Main Button shortly. You will hear the
caller’s voice in your hearing instruments.
emember
your voice is picked up by iCom.
쐍During a call the second phone cannot be
picked up
쐍If two phones are connected at the same time,
Voice dial applies to the last paired
G G
sing iCom with a cordless (DECT) or older phones
sing cordless phones (DECT) or older phones
with “Headset” profile only
Note: For these phones the Bluetooth indicator
(blue light) might not blink even if the phone was
paired before.
Step 1: On the phone, type the number you want
to dial or select it from the phone book
Step 2: Briefly press the Main Button (or press it
for 2 seconds if you are already in a streaming
iCom program)
Step 3: Wait for 5 seconds
Step 4: The dialing process will start and your
hearing system switches to the phone program
automatically
Features in iCom
Voice dial
Please refer to the phone user manual for instructions.
Press the Main Button for 2 seconds. After you hear
a beep, say the name of the contact you want to call.*
Last number redial
To redial the last number dialled, press the Main
Button twice. The last number dialled is activated
and the call is made.*
* The phone must support these features and the
features must be enabled by your hearing care
professional.
iCom must be switched on but no call and no
music or FM listening is in progress.
Audio lock
You are using the audio cable (jack) or an FM receiver.
But during a speaker pause or very soft music the audio
signal somtimes drops out.
Then press the ON/OFF button shortly to “lock” the
audio signal.