Phonak Lyric 3 User manual

User Guide for professionals
Lyric3programming wand

Introducing the new Lyric3 programming wand from
Phonak.
The Lyric3 programming wand is designed specically for
use by you, the hearing care professional, and enables
the wireless transfer of tting data from your PC to your
client’s Lyric3 hearing instruments.
Please read this manual carefully to benet from all the
features of your Lyric3 programming wand.
Phonak – life is on
Welcome

aTip
bStatus LED
cProgramming button
left / right
dWand body
eUSB cable
e
d
b
a
c
Description

To connect the Lyric3 programming wand, plug the USB-
plug into an available USB-port on your tting computer.
There is no driver installation required for the Lyric3
programming wand.
After successful set-up, the status LED on the wand will
turn green to indicate that the wand is ready for use.
Getting started

To program, hold the tip of the wand close to the lateral
end of the Lyric3 hearing aid and press the programming
button according to the ear you want to t. The status
LED will ash green during programming.
The status LED turns back to solid green after 3 seconds.
The wand is then ready for the next programming
procedure.
Programming

Lyric3 will play a double beep to indicate that it has
been programmed. When Lyric3 is programmed for the
rst time, it will switch from “Ship Mode” to ON when
successfully programmed. This can be veried by listening
for feedback or using a listening stethoscope.
If programming is performed in the ear, ask the patient
to pay attention and conrm the beeps to make sure the
programming was successful.

If an error occurs during programming, the status LED
will ash orange for 3 seconds before turning back to
green. In that case repeat the programming procedure.
If any other malfunctions occur with the wand, the
status LED will turn red. In that case, reboot the wand by
disconnecting and reconnecting it to the USB-port.
The status LED will ash red when the rmware of the
wand is updated. Wait until it turns back to green before
programming. Do not disconnect the wand during the
rmware update.
Further indicators

To clean the programming tip of the wand use a
disinfectant wipe if necessary. To clean the wand body,
use a mild detergent. The wand must not be dipped
in water or other detergents.
Hereby Phonak AG declares that this Phonak product is
in compliance with the essential requirements of the
Medical Devices Directive 93/42/EEC. The full text of the
Declaration of Conformity can be obtained from the
manufacturer or the local Phonak representative whose
address can be taken from the list on www.phonak.com
(worldwide locations).
Care and maintenance
Compliance information

Please read the information on the following pages
before using your Lyric3 programming wand.
The intended use of the Lyric3 programming wand
is to program Lyric3 hearing aids with tting
parameters.
Changes or modications to the Lyric3 programming
wand are not permitted. Such changes may damage
the Lyric3 programming wand. Phonak is not
responsible for situations resulting from a modied
device.
The Lyric3 programming wand contains a magnet.
If a medical device like a pacemaker is used, read the
specic user guide to clarify possible impact of
magnetic elds to the medical device. Keep a distance
of at least 15 cm (6 inches) between the Lyric3
programming wand and the medical device.
Important safety information

Never immerse the Lyric3 programming wand in water.
Protect it from excessive moisture as it contains
sensitive electronic parts.
Protect your Lyric3 programming wand from heat
(never leave near window or in a car). Never use a
microwave or other heating devices to dry the Lyric3
programming wand.
Do not drop the Lyric3 programming wand! Dropping
onto a hard surface can damage your Lyric3
programming wand.
Do not use the Lyric3 programming wand in areas
where electronic equipment is prohibited.