Photoneo PhoXi 3D Scanner M User manual

PhoXi 3D Scanner M
Quick Start Guide
Scope of Delivery
■PhoXi 3D Scanner M
■Power adapter (90 - 264VAC / 12VDC, 60W) (1)
■Power cable (2)
■Ethernet cable adapter (3)
■L-shaped mounting plate





Operation of the Scanner
The scanner is operated by the PhoXi Control application. PhoXi Control allows the user to
control the scanner either manually through a graphical user interface or programmatically
through the provided API.
All PhoXi Control resources can be found on the following link:
www.photoneo.com/3d-scanning-software/
Read the complete PhoXi 3D Scanner Manual for more details:
www.photoneo.com/support 
01/2020 PhoXi 3D Scanner M - Quick Start Guide 1/8


Scanning Parameters - Model M
Parameter
Value
Resolution
Up to 3.2 Million 3D points
Scanning range
458 - 1118mm
Optimal scanning distance (focus)
650mm
Scanning area (at focus distance)
590 x 421mm
Point to point distance (at focus distance)
0.284mm
Calibration accuracy
0.1mm
Temporal noise
0.1mm
Scanning time
250 - 2500ms
Dimensions
77 x 68 x 416mm
Baseline
350mm
Weight
950g
3D point throughput
16 Million points per second

These parameters are valid at 25°C, at focus distance for white objects with 80 % albedo.
 
01/2020 PhoXi 3D Scanner M - Quick Start Guide 2/8

Scanning Volume - Model M
 
01/2020 PhoXi 3D Scanner M - Quick Start Guide 3/8

Mounting the Scanner

Mounting options:
■Use 4x M4 screws with the supplied mounting plate.
■Use a M8 screw.
■Use a 3/8 - 16 UNC screw with a tripod.

Installation site restrictions:
■Ensure that mounting construction is rigid enough to avoid vibrations during scanning.
■Allow clearance of 25 mm for natural convection cooling.
■The ambient temperature range for the scanner operation is 0 °C to 30 °C.
■Separate the scanner from high-voltage devices and devices generating high electrical
noise.
The complete environment conditions for installation can be found in the full user manual at
www.photoneo.com/support 
01/2020 PhoXi 3D Scanner M - Quick Start Guide 4/8

Connecting to the Scanner
Ethernet port:
■1Gbps ethernet adapter with RJ45
socket
■Category Cat5e or better ethernet
cables
■PoE is not supported
Power + GPIO port:
■12VDC power supply
■Use only the supplied power
adapter
■The I/O ports are reserved for
future use
Ethernet Pinout

Power Pinout
Pin
Pinout

Pin
Pinout
1
MD1_P

1
IN2: laser interlock (5 - 12V)
2
12V_IN

2
IN1
3
MD2_N

3
OUT2
4
MD2_P

4
OUT1
5
MD0_P

5
POWER_+12VDC
6
MD0_N

6
POWER_GND
7
MD3_P

7
GPIO1
8
GND

8
GPIO3
9
MD1_N

9
GPIO2
10
MD3_N

10
IN_GND: laser interlock ground



11
OUT_GND



12
GPIO4
01/2020 PhoXi 3D Scanner M - Quick Start Guide 5/8


Status LEDs
The LEDs indicate the following states of the scanner:
Supported Network Topologies
 
01/2020 PhoXi 3D Scanner M - Quick Start Guide 6/8

Made-to-Order Cables
The following cables are available for additional purchase in standard or industrial quality:
■Power cable (from power adapter to device)
■Ethernet cable
All cables are available in the following lengths:
■3 m, 5 m, 10 m, 15 m.
Our industrial ethernet cables are sheathed in polyurethane jackets for high flexibility,
durability, and resistance to chemicals, water, and UV.
Our industrial power cables are sheathed in flex polyvinyl chloride jackets for high flexibility
and resistance to oils, water, and UV.
Custom Cables
■In case custom cables are used, the voltage must reach 12 V at the device end.
■Longer custom cables should have wires of a larger diameter to compensate for
voltage losses.
■When using custom cables, any damage caused to the device due to incorrect voltage
is exempt from warranty.
■Powering the device through the ethernet connector (PoE) is not possible.
Operating voltage Ue DC
12V
Residual ripple maximum (% of Ue)
5%
Rated operating current Ie(Imax)
2A (3A)
WARNING
Not ensuring the correct voltage at the device end may negatively influence
the correct functionality of the device or cause permanent damage.
01/2020 PhoXi 3D Scanner M - Quick Start Guide 7/8

Safety
PhoXi 3D Scanner Model M is a laser class 3R device or a laser class 2 device. Class 3R
lasers are considered safe when handled carefully. Class 2 lasers are considered safe for
normal operation. See the label on the back of the device to determine its laser class.
Laser class 3R label
Laser class 2 label



WARNING
Do not deliberately look into the laser beam. This may cause injury
to the retina.
Laser protective eyewear is normally not necessary.


Contact Us

Headquarters
Photoneo s.r.o.
Plynarenska 1
82109 Bratislava
Slovakia
Web
www.photoneo.com

Support
[email protected]

Business Inquiries
[email protected]

01/2020 PhoXi 3D Scanner M - Quick Start Guide 8/8