Pickering 42-204 User manual

pickeringtest.com
Issue 1.3 May 2022
40/42-204 User Manual
PXI/PXIe 1000Base-T1 Dual MUX With Fault Insertion

Page (II) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
Page (II) REED RELAY MODULE 40-110/115/120/125
pickering
© COPYRIGHT (2022) PICKERING INTERFACES. ALL RIGHTS RESERVED.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by
any means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
ISO 9001
Reg No. FM38792

Page (III)
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
Page (III)
REED RELAY MODULE 40-110/115/120/125
pickering
TECHNICAL SUPPORT
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
WARRANTY
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of
three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be
defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
ENVIRONMENTAL POLICY
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and
safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can
be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Worldwide Technical Support and Product Information
pickeringtest.com
Germany
Tel: [phone]
E-mail: [email protected]
Sweden
Tel: [phone]
E-mail: [email protected]
USA
Tel: (West) [phone]
Tel: (East) [phone]
E-mail: [email protected]
Czech Republic
Tel: [phone]
E-mail: [email protected]
France
Tel [phone]
E-mail [email protected]
Pickering Interfaces Headquarters
Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom
Tel: [phone]
E-Mail: [email protected]
China
Tel: [phone]
E-mail: [email protected]

Page (IV) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
Page (IV) REED RELAY MODULE 40-110/115/120/125
pickering
MEANING / DESCRIPTION SYMBOL
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an external conductor for
protection against electric shock in case of a fault, or the terminal of a protective earth
(ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING / CAUTION
An appropriate safety instruction should be followed or caution to a potential hazard
exists.
Refer to the relevant instructions detailed within the product manual.
HEAVY
If this product is heavy reference should be made to the safety instructions for
provisions of lifting and moving.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling precautions should
be followed.
!
kg
SAFETY SYMBOLS
PRODUCT SAFETY
The following safety symbols may be used on the product and throughout the product documentation.

Page (V)
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
Copyright Statement ...................................................................II
Technical Support and Warranty................................................III
Product Safety .............................................................................IV
Contents (this page)....................................................................V
Warnings and Cautions ..............................................................VII
Section 1
Technical Specication...............................................................1.1
Section 2
Technical Description .................................................................2.1
Functional Description..........................................................2.1
Multiplexer Ground................................................................2.1
Section 3
Installation....................................................................................3.1
Pre Operation Checks...........................................................3.1
Hardware Installation ............................................................3.2
Software Installation .............................................................3.2
Testing Operation ..................................................................3.3
Section 4
Programming Guide....................................................................4.1
Programming Options For PXI/PXIe Modules.....................4.1
Module Architecture..............................................................4.2
Programming The Module ....................................................4.3
Section 5
Connector Information................................................................5.1
Section 6
Trouble Shooting .........................................................................6.1
Section 7
Maintenance Information............................................................7.1
Relay Lookup Table...............................................................7.2
CONTENTS

Page (VI) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
THIS PAGE INTENTIONALLY BLANK

Page (VII)
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
Page (VII)
2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579
pickering
WARNINGS AND CAUTIONS
WARNING - HAZARDOUS ENVIRONMENTS SYMBOL
This product is not specically designed for use in hazardous environments, for example in explosive
atmospheres. If the product is to be used in hazardous environments we recommend that the user
ensures suitable protective measures are taken.
!
WARNING - DANGER OF ELECTRIC SHOCK SYMBOL
This module may contain hazardous voltages. Before removing the module from the rack remove all
supplies and disconnect user I/O signals.
Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O
signals that may be present. Blanking panels are available to order from Pickering in a variety of
slot widths. If the product is not used in this manner for example by using an extender card then
additional care must be taken to avoid contact with exposed signals.
Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.
This module must not be used for the switching of Mains Circuits. For the switching of voltages up
to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must
be fully isolated from the Mains Circuit and the safety earth.
The host chassis must be correctly installed and be connected to mains or factory safety ground,
please refer to your chassis installation manual.
Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT
For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage
Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved
by a transformer in which the primary windings are separated from the secondary windings by
reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.
CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL
Certain semiconductor devices used in this equipment are liable to damage due to static voltage.
Observe the following precautions when handling these devices in their unterminated state, or
sub-assemblies containing these devices:
1. Persons removing sub-assemblies from equipment using these devices must be earthed by a
wrist strap and a resistor at the point provided on the equipment.
2. Soldering irons used during the repair operations must be low voltage types with earthed tips and
isolated from the mains voltage by a double insulated transformer.
3. Outer clothing worn must be unable to generate static charges.
4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in
anti-static bags.
PXI Switching
Module
Device
Under Test
Power
Supply
Power
Supply
Host Chassis
Secondary Circuit
Mains
Circuit
Mains
Circuit
Mains/Factory
Safety Ground

Page (VIII) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579
pickering
CAUTION - PRODUCT DOCUMENTATION SYMBOL
Suitably qualied & trained users should ensure that the accompanying documentation is fully read
and understood before attempting to install or operate the product.
!
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O
signals (refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or
the combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the
chassis and the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on
the front of the unit.

Page 1.1
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering SECTION 1 - TECHNICAL SPECIFICATION
SECTION 1 - TECHNICAL SPECIFICATION
pickeringtest.com
PXI/PXIe 1000Base-T1 Dual MUX With Fault Insertion 40/42-204
ISSUE 1.3 MAY 2022
yAvailable as PXI or PXIe Modules
ySuited for 1000Base-T1/100Base-T1 Switching
yFault Insertion on 1 or 2 Channels of 2 Wire
Connections
yDual MUX for External Systems
yControlled Transmission Line Impedance
ySimple Insertion of Shorted Pair, Open and
Battery/Ground Connection
yVISA, IVI & Kernel Drivers Supplied for
Windows
ySupported by PXI or LXI Chassis
y3 Year Warranty
Fault Connections
FB1 FB2
M+
M-
M-LOOP+
M-LOOP-
U+
U-
U-LOOP+
U-LOOP-
40/42-204-001 Single Channel 1000Base-T1
Fault Insertion Switch Schematic Diagram
The 40-204 (PXI) and 42-204 (PXIe) are designed
to simulate common faults on high-speed two wire
communication interfaces such as 1000Base-T1. They
support 1 or 2-channels of two wire serial interfaces. Each
channel pair can be looped out to external equipment or
the switches can be used simulate a channel open fault.
Using the fault bus, switches can simulate a short between
both wires or a short to one of two externally applied fault
conditions – such as battery supply or ground - via two
fault buses.
Each channel can carry up to 0.8 A and is rated up to 200 V
between wire pairs. The wire pairs have controlled
transmission line impedance suited to most differential
Pickering’s Range of Fault Insertion Switches
Model No. Signal
Channels
Fault
Buses
Fault
Inputs
Max
Voltage
Max Current
or Bus Type
40-190B 74, 64 or 32 1 or 2 4 or 8 165 V 2 A
40-191A 6 2 2 40 V 30 A
40-192 6 2 2 200 V 10 A
40-193 7 1 or 2 1 or 2 16 V 20 A, 1 A min
40-194 7 1 or 2 1 or 2 16 V 20 A, no min
40-195 22 or 11 pairs — 8 or 4 150 V 1 A
40-196 10 or 5 pairs — 10 or 5 110 V 5 A
40-197A 34 or 16 4 8 300 V 2 A
40-198 20 1 or 2 3 or 6 250 V 5 A
40-199 10 1 or 2 2 250 V 10 A
40-200 4 or 8
differential 4 8 100 V CAN, FlexRay
40-201 4 or 8
differential 2 4 100 V Ethernet/AFDX /BroadR-Reach
40-202 22 or 11 pairs — 22 or 11 150 V 1 A
40/42-204 1 or 2
differential 2 2 200 V 1000Base-T1
signalling systems, including high-speed 1000Base-T1,
the fault buses are capable of carrying 0.8 A and also
have controlled transmission line impedance. The front
panel signal connectors are easy to use MMCX which are
fully supported by our range of connector accessories.
The module uses high quality electro-mechanical relays
designed for high frequency application with long service
life.
Differential Bus Switching
We also offer the 40-736 and 40-737 multiplexers which
are suitable for switching Ethernet, USB and other serial
communications signals.

Page 1.2 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
SECTION 1 - TECHNICAL SPECIFICATION
1000Base-T1 Dual MUX, 40/42-204
pickeringtest.com
Specifications
Power Requirements - 40-204
+3.3 V +5 V +12 V -12 V
0.03 A 0.3 A 0 0
Power Requirements - 42-204
+3.3 V +12 V
0.03 A 0.15 A
Operating/Storage Conditions
Operating Conditions
Operating Temperature:
Humidity:
Altitude:
0 °C to +55 °C
Up to 90 % non-condensing
5000 m
Storage and Transport Conditions
Storage Temperature:
Humidity:
Altitude:
-20 °C to +75 °C
Up to 90 % non-condensing
15000 m
PXI & CompactPCI Compliance - 40-204
The module is compliant with the PXI Specification 2.2.
Local Bus, Trigger Bus & Star Trigger are not implemented.
Uses a 33 MHz 32-bit backplane interface.
PXIe Compliance - 42-204
The module is compliant with the PXIe Specification 1.0.
Local Bus, Trigger Bus & Star Trigger are not implemented.
Safety & CE Compliance
All modules are fully CE compliant and meet applicable
EU directives: Low-voltage safety EN61010-1:2010,
EMC Immunity EN61326-1:2013,
Emissions EN55011:2009+A1:2010.
Mechanical Characteristics
40-204 - Single slot 3U PXI (CompactPCI card).
42-204 - Single slot 3U PXIe, compatible with PXIe hybrid
slot.
Module weight: 210g
3D models for all versions in a variety of popular file
formats are available on request.
Connectors
40-204 - PXI bus via 32-bit P1/J1 backplane connector.
42-204 - PXIe bus via XJ3 and XJ4 backplane connectors.
Signals via front panel mounted MMCX coaxial connectors.
Specification
Configuration: 1 or 2-pairs of two wire connections
designed for use on differential
serial interfaces with multiplexers
for connection to external
equipment.
Faults Simulated: Open on wire pairs or loop out to
external fault system via 2 fault
buses (for dual versions, the fault
buses for each bank are isolated
from each other).
Ground Connection: Each multiplexer bank has isolated
ground planes that are directly
connected to the outer of the front
panel connectors.
Differential Line
Impedance: 100 Ω
Fault Bus
Impedance: 50 Ω
Voltage Rating:
Carry Current
Rating:
Max Hot Switch
Current:
200 V*
0.8 A
0.5 A
Path Resistance: <1 Ω
Typical Bandwidth: >700 MHz Differential
Operate Time: 0.5 ms
* For full voltage rating, signal sources to be switched
must be fully isolated from mains supply and safety earth.

Page 1.3
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering SECTION 1 - TECHNICAL SPECIFICATION
1000Base-T1 Dual MUX, 40/42-204
pickeringtest.com
Ordering Information
Mating Connectors & Cabling
For connection accessories for the 40/42-204 module
please refer to the 90-011D RF Connector Accessories
data sheet where a complete list and documentation
can be found for accessories, or refer to the Connection
Solutions catalog.
Product Order Codes
PXI 1000Base-T1 Dual MUX With Fault Insertion:
1-Channel
2-Channel
40-204-001
40-204-002
PXIe 1000Base-T1 Dual MUX With Fault Insertion:
1-Channel
2-Channel
42-204-001
42-204-002
Product Customization
Pickering modules are designed and manufactured on our
own flexible manufacturing lines, giving complete product
control and enabling simple customization to meet very
specific requirements.
Customization can include:
• Alternative relay types
• Mixture of relay types
• Alternative number of relays
• Different performance specifications
All customized products are given a unique part number,
fully documented and may be ordered at any time in the
future. Please contact your local sales office to discuss.
42-204-001 PXIe 1-Channel
PXIe 1000Base-T1 Fault Insertion Switch

Page 1.4 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
SECTION 1 - TECHNICAL SPECIFICATION
1000Base-T1 Dual MUX, 40/42-204
pickeringtest.com
Supporting Products & Software
We also offer customized cabling and have a free online Cable Design Tool
that can be used to create custom cable solutions for many applications.
Visit: pickeringtest.com/cdt to start your design.
Mass Interconnect
We recommend the use of a mass interconnect solution when an
Interchangeable Test Adapter (ITA) is required for a PXI or LXI based test
system. Our modules are fully supported by both Virginia Panel and MacPanel.
Pickering Reed Relays
We are the only switch provider with in-house reed relay manufacturing
capability via our Relay Division. These instrument grade reed relays feature
SoftCenter™ technology, ensuring long service life and repeatable contact
performance. To learn more, please go to: pickeringrelay.com
Chassis Compatibility
The PXI versions of this module must be used in a suitable chassis. They are compatible with the following chassis types:
• All chassis conforming to the 3U PXI and 3U Compact PCI (cPCI) specification
• Legacy and Hybrid Peripheral slots in a 3U PXI Express (PXIe) chassis
• Pickering Interfaces LXI or LXI/USB Modular Chassis
The PXIe versions of this module are compatible with the following chassis types:
• All chassis conforming to the 3U PXIe specification
• PXIe and Hybrid Peripheral slots in a 3U PXI Express (PXIe) chassis
Chassis Selection Guide
Standard PXI or hybrid PXIe Chassis from any Vendor:
• Mix our 1000+ PXI switching & simulation modules with
any vendor’s PXI instrumentation
• Embedded or remote Windows PC control
• Real-time Operating System Support
• High data bandwidths, especially with PXI Express
• Integrated module timing and synchronization
Pickering LXI or LXI/USB Modular Chassis—only accept
our 1000+ PXI Switching & Simulation Modules:
• Ethernet or USB control enables remote operation
• Low-cost control from practically any controller
• LXI provides manual control via Web browsers
• Driverless software support
• Power sequencing immunity
• Ethernet provides chassis/controller voltage isolation
• Independence from Windows operating system
Connectivity Solutions
We provide a full range of supporting cable and connector solutions for all our switching products—20 connector families
with 1200+ products. We offer everything from simple mating connectors to complex cables assemblies and terminal blocks.
All assemblies are manufactured by Pickering and are guaranteed to mechanically and electrically mate to our modules.
Connectors & Backshells Multiway Cable Assemblies RF Cable Assemblies Connector Blocks

Page 1.5
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering SECTION 1 - TECHNICAL SPECIFICATION
1000Base-T1 Dual MUX, 40/42-204
pickeringtest.com
Supporting Products & Software
© Copyright (2022) Pickering Interfaces. All Rights Reserved Pickering Interfaces maintains a commitment to continuous product development, consequently we reserve the right to vary from the description given in this data sheet.
Programming
Pickering provide kernel, IVI and VISA (NI & Keysight) drivers which are compatible with all Microsoft supported versions of
Windows and popular older versions. For a list of all supporting operating systems, please see: pickeringtest.com/os
The VISA driver is also compatible with Real-Time Operating Systems such as LabVIEW RT. For other RTOS support contact
Pickering. These drivers may be used with a variety of programming environments and applications including:
• Pickering Interfaces Switch Path Manager
• National Instruments products (LabVIEW, LabWindows/CVI, Switch Executive, MAX, TestStand, VeriStand, etc.)
• Microsoft Visual Studio products (Visual Basic, Visual C+)
• Keysight VEE and OpenTAP
• Mathworks Matlab
• Marvin ATEasy
• MTQ Testsolutions Tecap Test & Measurement Suite
Drivers for popular Linux distributions are available, other environments are also supported, please contact Pickering
with specific enquiries. We provide Soft Front Panels (SFPs) for our products for familiarity and manual control, as well as
comprehensive documentation and example programs to help you develop test routines with ease.
To learn more about software drivers and development environments, please go to: pickeringtest.com/software
Signal Routing Software
Our signal routing software, Switch Path Manager, automatically selects and energizes
switch paths through Pickering switching systems. Signal routing is performed by simply
defining test system endpoints to be connected together, greatly accelerating Test System
software development. To learn more, please go to: pickeringtest.com/spm
Diagnostic Relay Test Tools
eBIRST Switching System Test Tools are designed specifically for our PXI,
PCI or LXI products, these tools simplify switching system fault-finding by
quickly testing the system and graphically identifying the faulty relay.
To learn more, please go to: pickeringtest.com/ebirst
Three Year Warranty & Guaranteed Long-Term Support
All standard products manufactured by Pickering Interfaces are warranted against defective materials and workmanship
for a period of three years from the date of delivery to the original purchaser. Extended warranty and service agreements
are available for all our modules and systems with various levels to suit your requirements. Although we offer a 3-year
warranty as standard, we also include guaranteed long-term support—with a history of supporting our products for typically
15-20 years. To learn more, please go to: pickeringtest.com/support
Available Product Resources
We have a large library of product resources including success stories, product and support videos, articles and white
papers as well as application specific product brochures to assist when looking for the switching, simulation and
connection solutions you need. We have also published handy reference books on Switching Technology and for the PXI
and LXI standards.
To view, download or request any of our product resources, please visit: pickeringtest.com/resources

Page 1.6 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
SECTION 1 - TECHNICAL SPECIFICATION
THIS PAGE INTENTIONALLY BLANK

Page 2.1
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering SECTION 2 - TECHNICAL DESCRIPTION
SECTION 2 - TECHNICAL DESCRIPTION
FUNCTIONAL DESCRIPTION
A functional block diagram is provided in Figure 2.1. The multiplexer module is powered by +5V and +3.3V (PXI)
or +3.3V and +12V (PXIe) supplies via PCI Bus connectors mounted on the mother board. The interface to the
user test equipment is via front panel mounted MMCX coaxial connectors. The module comprises a mother
PCB and one daughter board (single bank versions) or two daughter boards (dual bank versions) populated
with electro-mechanical relays. The banks are arranged as a differential signal path with input and output loop-
thru switching and two switched fault buses that allow the insertion of external signals or short-circuit emulation.
The relays are energised with control signals from relay drivers driven by PCI bridge and control logic. Module
conguration is determined by data stored in EEPROM also, the PCI Bridge is congured by EEPROM.
Memory
U9-10
Level
Shifters
U2-3
PCI Bridge U1
Mother Board
+3.3V
GND
Configuration
Memories
U7-8
Compact PCI Bus Connector or PXIe Connectors
PXI/PXIe 1000Base-T1 Dual MUX With Fault Insertion 40/42-204
+5V (PXI)
+12V (PXIe)
Daughter Board
PCB Interconnection
Front Panel MMCX Connectors
Relays RL1-6
Relay
Drivers
Relay
Drivers
Front Panel MMCX Connectors
Daughter Board
Multiplexer
Bank 1
Relays RL1-6
Multiplexer
Bank 2
Figure 2.1 - 1000Base-T1 Dual MUX 40/42-204: Functional Block Diagram
Multiplexer Ground Connection
Each multiplexer bank has a ground connection via the outer of its front panel coaxial connectors. This is isolated
from the front panel and, in the case of dual versions, from the adjacent bank. The multiplexer ground and front
panel ground can be connected together by tting links on the module’s daughter boards. For dual versions, tting
links to both daughter boards will connect the bank’s grounds together (also connecting them to the front panel
ground). For the locations of the links, see Figure 7.2 in Section 7 of this manual.

Page 2.2 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
SECTION 2 - TECHNICAL DESCRIPTION
THIS PAGE INTENTIONALLY BLANK

Page 3.1
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering SECTION 3 - INSTALLATION
Page 3.1
REED RELAY MODULE 40-110/115/120/125
pickeringSECTION 3 - INSTALLATION
kg
PREOPERATION CHECKS (UNPACKING)
1. Check the module for transport damage and report any damage immediately to Pickering Interfaces.
Do not attempt to install the product if any damage is evident.
2. Position the chassis relative to any other equipment the module(s) will connect with. Ensure the chassis is not
connected to the electrical supply.
3.
withstand and support the combined weight of the module(s) and chassis.
SECTION 3 - INSTALLATION
!
Refer to the Warnings and Cautions at the front of this manual
Modular products require installation in a suitable PXI/PXIe/LXI chassis. The module is for indoor use only.
Figure 3.1 - Installing the Module into a PXI/PXIe/cPCI/LXI Chassis
PXI / PXIe / LXI Chassis
Ensure that the designated area for the chassis containing the module is of flat and solid construction to
PXI / PXIe Module

Page 3.2 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
SECTION 3 - INSTALLATION
Page 3.2 REED RELAY MODULE 40-110/115/120/125
pickering
SECTION 3 - INSTALLATION
SOFTWARE INSTALLATION
First install the appropriate Pickering PXI switch card drivers by running the installer program Setup.exe (provided
in a compressed zip le), either from the CD-ROM supplied, or by downloading the latest version from our website
pickeringtest.com - the recommended method. Setup is accompanied by a ReadMe le containing
additional installation information. A single installation covers all cards in the System 40, System 45 and System
50 ranges.
When installation completes, the installed drivers’ ReadMe le is offered for display. It can also be displayed
later using a shortcut on the Programs>>Pickering menu.
If you are not a LabVIEW user you should choose the “full” version, and once that has been installed run
the LabVIEW Runtime Engine installer via the shortcut on the Programs>>Pickering menu. In the absence of
LabVIEW the Runtime Engine is required to support the Pickering Test Panels application.
!
HARDWARE INSTALLATION
ELECTRICAL CONNECTION (CHASSIS)
1. The chassis must be electrically installed in accordance with local regional electrical codes by a qualied
engineer.
2. The chassis must be grounded.
Electrostatic discharge can damage the components on the module. To avoid such damage in handling the
board refer to page VII.
Ensure that there is adequate ventilation.
The module should be installed in accordance with the following procedure:
1. Ensure that the system is turned OFF but still connected to mains so that it remains grounded.
2. Choose an appropriate slot in the rack.
3. Remove the blanking plate for the chosen slot.
4. Ensure that the injector/ejector handle is in its downward position. Align the module with the card guides on
the top and bottom of the slot.
Do not raise the injector/ejector handle whilst inserting the module as the module will not insert properly.
5. Hold the handle whilst slowly sliding the module into the card guides until the handle catches on the injector/
ejector rail (refer to Figure 3.1).
6. Raise the injector/ejector handle until the module rmly seats into the backplane. The front panel of the
module should be ush with the front panel of the chassis.
7. Secure the front panel of the module using both screws to the chassis front panel mounting rails.
8. In a system employing a remote control interface to connect an external controller to a PXI chassis or to link
multiple chassis, power-up the system as follows:
a. For a system comprising an external controller and one chassis, power up the chassis before powering up
the external controller.
b. For a system comprising more than one chassis, turn ON the last chassis in the system followed by the
penultimate, etc, and nally turn ON the external controller or chassis containing the system controller.
9. For Pickering Interfaces modular LXI installation there is no requirement to use any particular power up
sequence.

Page 3.3
PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering SECTION 3 - INSTALLATION
Page 3.3
REED RELAY MODULE 40-110/115/120/125
pickering SECTION 3 - INSTALLATION
Figure 3.3 - General Soft Front Panel Selector
TESTING OPERATION
After installation of the hardware and Pickering PXI Driver software package start the General Soft Front
Panel (GSFP) using the desktop icon or via the Start menu (Start Menu-> Pickering Interfaces Ltd ->
General Soft Front Panel).
A selector panel will appear, listing all installed Pickering PCI, PXI or LXI switch cards and resistor cards. Click
on the card you wish to control, and a graphical control panel is presented allowing operation of the card.
Panels can be opened simultaneously for all the installed cards.
More details how to use the GSFP can be found in the manual, via menu Help\Manual
Figure 3.2 - General Soft Front Panel Icon

Page 3.4 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204
pickering
SECTION 3 - INSTALLATION
THIS PAGE INTENTIONALLY BLANK