PICOTE Sentinel Guard 2.0 Instruction Manual

I
N
S
T
R
U
C
T
I
O
N
S
Operating & Safety Manual
Sentinel Guard 2.0
These instrucons are for your personal safety. Always ensure that
you have read and understood these instrucons before using the
machinery. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
We now have resellers in the U.S., Europe & Australasia.
Locate your reseller at picotesolutions.com

2
TOPIC PAGE/S
SAFETY INFORMATION & SYMBOLS 3
OVERVIEW 5
FEATURES 6
FUNCTIONS & USAGE 8
CHANGING SETTINGS & SMS COMMANDS 9
MAINTENANCE & SPARE PARTS 11
WARRANTY POLICY & PROCEDURE 12
To watch practical demonstration videos, or to download an electronic copy of these In-
structions, please visit www.picotesolutions.com. Please note that videos are not intend-
ed as a replacement or alternative to this operating and safety manual, but only as an
additional learning tool.
TABLE OF CONTENTS

3
SAFETY INFORMATION
This section contains important safety information. Failure to
comply could result in serious injury or death.
Safety Symbols
Safety symbols are used throughout this manual to draw attention to potential hazards.
Personal Protective Equipment (PPE)
Always use Personal Protective Equipment which is needed on a working site where the
Sentinel Guard 2.0 is being deployed.
Danger risk of serious injury, follow instructions.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
TRANSPORT
Sennel Guard 2.0should be transported in car or other vehicle secured so that any sudden movements caused by hard
braking or accident are prevented. Always tranport Sennel inside the vehicle.
STORAGE
Sennel Guard 2.0 should be strored under cover in condensaon frost free environment. It is recemmended that Sen-
nel units are stored indoors protected from rain and sunlight and in and constant ambient temperature.
If Sennel will be stored in colder environment than +10 oC (50 oF ), the machine should be stood at room temperature
for 24hours before use.
DISPOSAL
Sennel Guard 2.0 can be disposed in Europe at Waste Electrical and Electronic Equipment (WEEE) collecon points.
Always follow the local waste handling rules and regulaon.
ENVIRONMENTAL
Operaonal Ambient Temperature Range: -10...50 oC (14...122 oF) frost and condensaon free
Storage Ambient Temperature Range: -20...60 oC (-4...140 oF) frost and condensaon free
Maximum Humidity: 95% non-condensing

4
Always read all safety warnings and instrucons. Failure to follow warnings and instrucons may result in electric
shock, re and/or serious injury.
GENERAL MACHINE SAFETY WARNING
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
SAFETY REQUIREMENTS
1. Always follow the instrucons in the Picote Soluons manual.
2. Before each use inspect the Sennel Guard 2.0 carefully for any potenal break or damage. Change damaged
sensors immediately.
3. When in use, it is very important that the Sennel Guard 2.0 is stable and on an even surface at all mes.
4. Do not open the lid of the Sennel Guard aer the SIM card has been placed inside.
5. If the working environment is extremely hot and humid, or badly polluted by conducve dust, use a GFCI-enabled
power outlet to ensure the safety of the operator.
6. Always check the internet connecon quality prior to use the Sennel Guard 2.0.
7. Only use the Sennel Guard 2.0 with the accessories and spare parts oered by Picote Soluons. Accessories and
spare parts should only be used in the manner intended and as described by Picote Soluons.
This secon contains important safety informaon. Failure to comply could result in serious injury or death.
This secon contains important safety informaon. Failure to comply could result in serious injury or death.

5
TECHNICAL DATA
Size
(mm/inches)
Air Pressure connectors Power
Supply Monitoring
Weight
(kg/lbs)
IP Rang
287x205x180
11”x8”x7”
2 110-230V / 50-60Hz
400V / 50-60Hz
5.8 / 12.8 67 sealed closed
INTENDED USE
This machine is intended for the following uses;
1. Monitoring pressure of the linings.
2. Monitoring power supply.
3. Monitoring water level in pumping staons.
4. Monitoring temperature.
Sennel 2.0 has a built in remote alarm feature. This allows it to send an alert message to a mobile phone
in cases of power outage, uctuaon of the pressure outside the limits or water level in a pumping staon
rise too high. The alerts will be sent by calling, text messages via the GSM network and email. User can
also check the situaon in working site in-me by logging on website hps://phoenix.onos..
GENERAL INFORMATION

6
SIM CARD
Ensure that the supply voltage is correct. The voltage of the power source must match the value given on the name-
plate of the machine within the tolerances of ±10 %. Machines with a 230V plate can be used in 220V mains and
110V machines in the 120V grid.
The machine has been double sealed according to European standards. The power source has to be grounded.
To begin using the Sennel 2.0 device, connect it to a mains power socket using the provided cable.
Always connect the power supply provided to the Sennel 2.0 unit. The unit has a back-up baery as well, but it is
only intended as a back-up for pressure measurement and to send alarm messages in the event of power failure, and
is NOT a substute for the mains power supply.
VOLTAGE & POWER SUPPLY
Sennel Guard uses a Mini sized SIM card. The SIM card slot is found under the lid. Once the SIM card has been in-
serted inside, the lid should be closed at all mes. Before inserng the SIM card into the Sennel Guard 2.0, the PIN
code lock must be turned o. This can be done by inserng the SIM card into a mobile phone and turning the PIN
code lock o.
It is recommended to use subscripon based SIM cards and not prepaid SIM cards. Prepaid SIM cards might run out
of credit or be closed down inconspicuously.
Step 1. Open Sennel Guard 2.0 lid.
Step 2. Turn the SIM card PIN code lock o with your mobile phone.
NOTE! Sennel Guard 2.0 uses Mini sized SIM card. Use adapter to make your SIM card larger if needed.

7
CONNECTORS
There are three dierent types of connectors in the Sennel Guard 2.0 device: pressure, water, and power. The pres-
sure connectors and water sensor connector are located on the le side of the Sennel 2.0 unit. The power supply
connector is located on the right side of Sennel unit.
When connecng the power supply connector or the water sensor connector, push the connector to the socket, and
screw the threaded nut all the way in. The power and water sensor connectors have a groove and cannot be connec-
ted if misaligned. The power and water sensor connectors have protecve covers that are meant to be used when
the connector is not in use.
START UP
To begin using the Sennel Guard 2.0 device, connect it to a mains power socket using the provided cable.
Always connect the power supply provided to the Sennel Guard 2.0unit. The unit has a back-up baery as well,
but it is only intended as a back-up for pressure measurement and to send alarm messages in the event of power
failure, and is NOT a substute for the mains power supply.
Step 3. Push the SIM card into the slot as shown below. Check that SIM card is properly locked into
the slot. Close the lid and test that you can connect to your Sennel Guard 2.0 unit in hps://
phoenix.onos..

8
STEP 1. Open a web browser on your computer and go to hps://phoenix.onos.
LOGGIN INTO THE SENTINEL 2.0
STEP 2. Insert the username and password that were provided with the device.
STEP 3. Click on the Home buon.
STEP 4. Click on the Phoenix you want to control.
STEP 5. You will now see the main view of your Sennel Guard 2.0.

9
STEP 1. Log into your Sennel Guard 2.0 as per secon Logging into the Phoenix.
STEP 2. In the boom le corner you will nd a panel tled ADD ALERT ADDRESS.
STEP 3. To add a phone number, insert the phone number with the country code.
STEP 4. Aer typing phone number, click ADD. To add an email address, insert the email address.
STEP 5. Verify that the alert addresses are now listed in the ALERT ADDRESSES panel above.

10
STEP 1. Log into your Sennel Guard 2.0 as per secon Logging into the Phoenix.
STEP 2. In the boom le corner you will nd a panel tled REMOVE ALERT ADDRESS.
STEP 3. To remove a phone number, insert the phone number with the country code.
STEP 4. To remove an email address, insert the email address.
STEP 5. Verify that the alert address you removed is no longer listed in the ALERT ADDRESSES panel.