Pilz PNOZ mc5p User manual

PNOZ mc5p
Operating Manual-21055-EN-05
}Configurable, safe small controllers PNOZmulti Classic

Preface
This document is the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for the user's internal purposes. Suggestions and comments for improving this documenta-
tion will be gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital

Contents
Operating Manual PNOZ mc5p
21055-EN-05 | 3
1 Introduction ............................................................................................................................4
1.1 Validity of documentation.......................................................................................................... 4
1.2 Using the documentation .......................................................................................................... 4
1.3 Definition of symbols................................................................................................................. 4
2 Overview .................................................................................................................................6
2.1 Scope........................................................................................................................................ 6
2.2 Unit features ............................................................................................................................. 6
2.3 Front view ................................................................................................................................. 6
3 Safety ...................................................................................................................................... 7
3.1 Intended use ............................................................................................................................. 7
3.2 System requirements................................................................................................................ 7
3.3 Safety regulations ..................................................................................................................... 8
3.3.1 Use of qualified personnel ........................................................................................................ 8
3.3.2 Warranty and liability ................................................................................................................ 8
3.3.3 Disposal .................................................................................................................................... 8
3.3.4 For your safety.......................................................................................................................... 8
4 Function description ............................................................................................................. 9
4.1 Functions .................................................................................................................................. 9
4.2 Input and output data................................................................................................................ 9
4.3 Assigning the inputs/outputs in the PNOZmulti Configurator to the INTERBUS inputs/outputs9
4.4 Block diagram ........................................................................................................................... 10
5 Installation ..............................................................................................................................11
5.1 General installation guidelines.................................................................................................. 11
5.2 Dimensions in mm .................................................................................................................... 11
5.3 Connecting the base unit and expansion modules ................................................................... 12
6 Commissioning ......................................................................................................................13
6.1 Preparing for commissioning .................................................................................................... 13
6.2 Setting the transmission rate .................................................................................................... 14
6.3 Connecting the supply voltage.................................................................................................. 14
6.4 Download modified project to the PNOZmulti safety system.................................................... 14
6.5 Connection example ................................................................................................................. 15
7 Operation ................................................................................................................................16
7.1 Messages ................................................................................................................................. 16
8 Technical Details ...................................................................................................................17
9 Order reference ......................................................................................................................19
9.1 Product ..................................................................................................................................... 19
9.2 Accessories .............................................................................................................................. 19

Introduction
Operating Manual PNOZ mc5p
21055-EN-05 | 4
1 Introduction
1.1 Validity of documentation
This documentation is valid for the product PNOZ mc5p. It is valid until new documentation
is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
1.2 Using the documentation
This document is intended for instruction. Only install and commission the product if you
have read and understood this document. The document should be retained for future ref-
erence.
1.3 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.

Introduction
Operating Manual PNOZ mc5p
21055-EN-05 | 5
INFORMATION
This gives advice on applications and provides information on special fea-
tures.

Overview
Operating Manual PNOZ mc5p
21055-EN-05 | 6
2 Overview
2.1 Scope
}Expansion module PNOZ mc5p
}Jumper
2.2 Unit features
Application of the product PNOZ mc5p:
Expansion module for connection to a base unit from the PNOZmulti system.
The product has the following features:
}Can be configured in the PNOZmulti Configurator
}Connection for INTERBUS
}Transmission rate, selectable between 500kBit/s and 2 MBit/s
}Status indicators for communication with INTERBUS and for errors
}Max. 1 PNOZ mc5p can be connected to the base unit
}In the PNOZmultiConfigurator, 24inputs (standard) and 24outputs (standard) can be
configured for communication via a fieldbus.
}Please refer to the document "PNOZmulti System Expansion" for the PNOZmulti base
units that can be connected.
2.3 Front view

Safety
Operating Manual PNOZ mc5p
21055-EN-05 | 7
3 Safety
3.1 Intended use
The fieldbus module PNOZ mc5p is an expansion module of the configurable control sys-
tem PNOZmulti. It is used for communication between the configurable control system
PNOZmulti and INTERBUS. INTERBUS is designed for fast data exchange at field level.
The expansion module PNOZ mc5p is a passive INTERBUS subscriber (Slave). The basic
functions of communication with INTERBUS conform to EN 50254. The central controller
(Master) reads input information from the slaves and writes output information to the slaves
as part of each cycle. As well as the cyclical transfer of usable data, the fieldbus module
PNOZ mc5p can also be used for diagnostics and commissioning functions.
The expansion module may only be connected to a base unit from the PNOZmulti system
(please refer to the document "PNOZmulti System Expansion" for details of the base units
that can be connected).
The configurable small control systems PNOZmulti are used for the safety-related interrup-
tion of safety circuits and are designed for use in:
}E-STOP equipment
}Safety circuits in accordance with VDE0113 Part 1 and EN60204-1
The expansion module may not be used for safety-related functions.
The following is deemed improper use in particular
}Any component, technical or electrical modification to the product,
}Use of the product outside the areas described in this manual,
}Use of the product outside the technical details (see Technical details [ 17]).
NOTICE
EMC-compliant electrical installation
The product is designed for use in an industrial environment. The product
may cause interference if installed in other environments. If installed in other
environments, measures should be taken to comply with the applicable
standards and directives for the respective installation site with regard to in-
terference.
3.2 System requirements
Please refer to the "Product Modifications PNOZmulti" document in the "Version overview"
section for details of which versions of the base unit and PNOZmulti Configurator can be
used for this product.

Safety
Operating Manual PNOZ mc5p
21055-EN-05 | 8
3.3 Safety regulations
3.3.1 Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.
A competent person is someone who, because of their training, experience and current pro-
fessional activity, has the specialist knowledge required to test, assess and operate the
work equipment, devices, systems, plant and machinery in accordance with the general
standards and guidelines for safety technology.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident prevention,
}Have read and understood the information provided in this description under "Safety",
}And have a good knowledge of the generic and specialist standards applicable to the
specific application.
3.3.2 Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended,
}Damage can be attributed to not having followed the guidelines in the manual,
}Operating personnel are not suitably qualified,
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
3.3.3 Disposal
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).
3.3.4 For your safety
The unit meets all the necessary conditions for safe operation. However, you should always
ensure that the following safety requirements are met:
}This operating manual only describes the basic functions of the unit. The expanded func-
tions are described in the PNOZmulti Configurator's online help. Only use these functions
once you have read and understood the documentations.
}Do not open the housing or make any unauthorised modifications.
}Please make sure you shut down the supply voltage when performing maintenance work
(e.g. exchanging contactors).

Function description
Operating Manual PNOZ mc5p
21055-EN-05 | 9
4 Function description
4.1 Functions
The data to be transferred via INTERBUS is selected and configured in the PNOZmulti
Configurator. The base unit and PNOZ fieldbus module PNOZ mc5p are connected via a
jumper. The fieldbus module is also supplied with voltage PNOZ mc5p via this jumper. After
the supply voltage is switched on or the safety system PNOZmulti is reset, the fieldbus
module PNOZ mc5p is configured and started automatically.
4.2 Input and output data
The data is structured as follows:
}Input area
The inputs are defined in the master and transferred to the PNOZmulti. Each input has a
number, e.g. input bit 4 of byte 1 has the number i12.
}Output range
The outputs are defined in the PNOZmulti Configurator. Each output that is used is given
a number there, e.g. o0, o5... The status of output o0 is stored in bit 0 of byte 0; the
status of output o5 is stored in bit 5 of byte 0 etc.
}Output range only: Byte 3
Bits 0 … 4: Status of LEDs on the PNOZmulti
– Bit 0: OFAULT
– Bit 1: IFAULT
– Bit 2: FAULT
– Bit 3: DIAG
– Bit 4: RUN
Bit 5: Data is being exchanged.
Detailed information on data exchange (tables, segments) is available in the document
"Communication Interfaces" in the section entitled "Fieldbus modules".
4.3 Assigning the inputs/outputs in the PNOZmulti Configurator
to the INTERBUS inputs/outputs
Virtual inputs on PNOZmulti Configurator i0 ... I7 i8 ... i15 i16 ... i23
Input data INTERBUS Byte 0: Bits 0 … 7 Byte 1: Bits 0 … 7 Byte 2: Bits 0 … 7
Virtual outputs on PNOZmulti Configurator o0 ... o7 o8 ... o15 o16 ... o23
Output data INTERBUS Byte 0: Bits 0 … 7 Byte 1: Bits 0 … 7 Byte 2: Bits 0 … 7
The number of virtual inputs and outputs can be extended to 128 (see document "Commu-
nication Interfaces" in the section entitled "Fieldbus modules")

Function description
Operating Manual PNOZ mc5p
21055-EN-05 | 10
4.4 Block diagram
IBS OUT
Base unit
IBS IN

Installation
Operating Manual PNOZ mc5p
21055-EN-05 | 11
5 Installation
5.1 General installation guidelines
}The control system should be installed in a control cabinet with a protection type of at
least IP54. Fit the control system to a horizontal mounting rail. The venting slots must
face upward and downward. Other mounting positions could destroy the control system.
}Use the locking elements on the rear of the unit to attach it to a mounting rail. Connect
the control system to the mounting rail in an upright position, so that the earthing springs
on the control system are pressed on to the mounting rail.
}The ambient temperature of the devices in the control cabinet must not exceed the figure
stated in the technical details. Air conditioning may otherwise be required.
}To comply with EMC requirements, the mounting rail must have a low impedance con-
nection to the control cabinet housing.
NOTICE
Damage due to electrostatic discharge!
Electrostatic discharge can damage components. Ensure against discharge
before touching the product, e.g. by touching an earthed, conductive sur-
face or by wearing an earthed armband.
5.2 Dimensions in mm
94 (3.70")
22,5
(0.88")
114 (4.49")

Installation
Operating Manual PNOZ mc5p
21055-EN-05 | 12
5.3 Connecting the base unit and expansion modules
You can install a maximum of 1 PNOZ mc5p to the left of the base unit.
Connect the base unit and the expansion module as described in the operating instructions
for the base units.
}Do not connect a terminator to the last expansion module on the left-hand side.
}Install the expansion module in the position in which it is configured in the PNOZmulti
Configurator.
}A distance of at least 20 mm must be maintained between the fieldbus module PNOZ
mc5p and any external heat sources.

Commissioning
Operating Manual PNOZ mc5p
21055-EN-05 | 13
6 Commissioning
6.1 Preparing for commissioning
The wiring is defined in the circuit diagram of the PNOZmulti Configurator.
It is possible to define which outputs on the safety system will communicate with INTER-
BUS. The connection to INTERBUS is made via two female 9-pin D-Sub screw connectors
5
1
6
9
1: DO1
2: DI1
3: GND
4: n.c.
5: n.c.
6: /DO1
7: /DI1
8: n.c.
9: n.c.
IBS IN
1
5
9
6
1: DO2
2: DI2
3: GND
4: n.c.
5: GND
6: /DO2
7: /DI2
8: n.c.
9: RBST
IBS OUT
n. c. = not connected
Please note:
}Information given in the "Technical details" must be followed.
}Use copper wiring with a temperature stability of 75 °C.
Please note the following when connecting to INTERBUS:
}Only use metal plugs or metallised plastic plugs
}Twisted pair, screened cable must be used to connect the interfaces
CAUTION!
Only connect and disconnect the expansion module when the supply
voltage is switched off.
NOTICE
When installing, please refer to the Installation Manual for fibre-optic cables,
issued by the INTERBUS User Organisation.

Commissioning
Operating Manual PNOZ mc5p
21055-EN-05 | 14
6.2 Setting the transmission rate
The transmission rate is set using a jumper. You can choose between 500kBit/s and 2
MBit/s.
500 kBit/s:
500k 2M
2 MBit/s
500k 2M
6.3 Connecting the supply voltage
Connect the supply voltage to the base unit:
}Terminal 24 V and A1 (+): + 24VDC
}Terminal 0 V and A2 (-): 0 V
6.4 Download modified project to the PNOZmulti safety system
As soon as an additional expansion module has been connected to the system, the project
must be amended in the PNOZmulti Configurator and downloaded back into the base unit.
Proceed as described in the operating manual for the base unit.
NOTICE
For the commissioning and after every user program change, you must
check whether the safety devices are functioning correctly.

Commissioning
Operating Manual PNOZ mc5p
21055-EN-05 | 15
6.5 Connection example
INTERBUS
Master
INTERBUS
Slave 1
INTERBUS
Slave 3
INTERBUS
Slave 2

Operation
Operating Manual PNOZ mc5p
21055-EN-05 | 16
7 Operation
When the supply voltage is switched on, the PNOZmulti copies the configuration from the
chip card.
The expansion module PNOZ mc5p is configured and started automatically.
7.1 Messages
Legend
LED on
LED off
LED Meaning
CR/CC green The cable connection is in order and the INTERBUS Master is
not in a reset condition.
The cable connection is defective or the INTERBUS Master is in
a reset condition.
OM green Data traffic present.
No data traffic.
RD yellow The remote bus is switched off (remote bus disabled).
The remote bus is switched on (remote bus enabled).

Technical Details
Operating Manual PNOZ mc5p
21055-EN-05 | 17
8 Technical Details
General
Certifications
CCC, CE, EAC (Eurasian), KCC, KOSHA, TÜV, cU-
Lus Listed
Electrical data
Supply voltage
for Module supply
internal Via base unit
Voltage 5 V
Kind DC
Voltage tolerance -2 %/+2 %
Power consumption 2,5 W
Status indicator LED
Fieldbus interface
Fieldbus interface INTERBUS-S
Device type Slave
Transmission rates 2 MBit/s, 500 kBit/s
Connection IBS IN 9-pin D-Sub male connector
Connection IBS OUT 9-pin D-Sub female connector
Galvanic isolation yes
Test voltage 500 V AC
Times
Supply interruption before de-energisation 20 ms
Environmental data
Ambient temperature
In accordance with the standard EN 60068-2-14
Temperature range 0 - 55 °C
Storage temperature
In accordance with the standard EN 60068-2-1/-2
Temperature range -25 - 70 °C
Climatic suitability
In accordance with the standard EN 60068-2-30, EN 60068-2-78
Humidity 93 % r. h. at 40 °C
Condensation during operation Not permitted
Max. operating height above sea level 2000 m
EMC EN 61131-2
Vibration
In accordance with the standard EN 60068-2-6
Frequency 10 - 150 Hz
Acceleration 1g
Shock stress
In accordance with the standard EN 60068-2-27
Acceleration 15g
Duration 11 ms

Technical Details
Operating Manual PNOZ mc5p
21055-EN-05 | 18
Environmental data
Airgap creepage
In accordance with the standard EN 61131-2
Overvoltage category III
Pollution degree 2
Rated insulation voltage 30 V
Protection type
In accordance with the standard EN 60529
Housing IP20
Terminals IP20
Mounting area (e.g. control cabinet) IP54
Mechanical data
Mounting position horizontally on mounting rail
DIN rail
Top hat rail 35 x 7,5 EN 50022
Recess width 27 mm
Material
Bottom PPO UL 94 V0
Front ABS UL 94 V0
Dimensions
Height 94 mm
Width 22,5 mm
Depth 119 mm
Weight 155 g
Where standards are undated, the 2020-07 latest editions shall apply.

Order reference
Operating Manual PNOZ mc5p
21055-EN-05 | 19
9 Order reference
9.1 Product
Product type Features Order No.
PNOZ mc5p Fieldbus module, INTERBUS 773 723
9.2 Accessories
Jumper
Product type Features Order No.
KOP-XE Jumper 774 639

The Best of
German
Engineering
Partner of:
Support
Technical support is available from Pilz round the clock.
Americas
Brazil
[phone]
Canada
[phone]
Mexico
[phone]
USA (toll-free)
+1 877-PILZUSA (745-9872)
Asia
China
[phone]
Japan
[phone]
South Korea
[phone]
Australia
[phone]
Europe
Austria
[phone]
Belgium, Luxembourg
[phone]
France
[phone]
Germany
[phone]
Ireland
[phone]
Italy, Malta
[phone]
Scandinavia
[phone]
Spain
[phone]
Switzerland
[phone]
The Netherlands
[phone]
Turkey
[phone]
United Kingdom
[phone]
You can reach our
international hotline on:
[phone]
suppor[email protected]
Pilz develops environmentally-friendly products using
ecological materials and energy-saving technologies.
Oces and production facilities are ecologically designed,
environmentally-aware and energy-saving. So Pilz oers
sustainability, plus the security of using energy-ecient
products and environmentally-friendly solutions.
We are represented internationally. Please refer to our homepage www.pilz.com
for further details or contact our headquarters.
Headquarters: Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [email protected], Internet: www.pilz.com
CECE®, CHRE®, CMSE®, InduraNET p®, Leansafe®, Master of Safety®, Master of Security®, PAS4000®, PAScal®, PASconfig®, Pilz®, PIT®, PLID®, PMCprimo®, PMCprotego®, PMCtendo®,
PMD®, PMI®, PNOZ®, PRBT®, PRCM®, Primo®, PRTM®, PSEN®, PSS®, PVIS®, SafetyBUS p®, SafetyEYE®, SafetyNET p®, THE SPIRIT OF SAFETY®are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries. We would point out that product features may vary from the details stated in this document, depending on the status at the time of publication and the scope of the equipment. We accept no responsibility for the validity, accuracy and entirety of the text and graphics presented in this information. Please contact our Technical Support
if you have any questions.
1800XXXX-en-0X, 2019-05 Printed in Germany
© Pilz GmbH & Co. KG, 2019
Back cover
21055-EN-05, 2020-07 Printed in Germany © Pilz GmbH & Co. KG, 2019