Pilz PSSnet SLL Series User manual

Industrial Ethernet Switches – PSSnet S
PSSnet SLL Series – Devices
Unmanaged Ethernet Switches
Installation – Mat- No. 22751 – EN- 1

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes.
uggestions and comments for improving this documentation will be gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, P EN®, P ®, PVI ®, afetyBU p®, afetyEYE®,
afetyNET p®, the spirit of safety® are registered and protected trademarks of
Pilz GmbH & Co. KG in some countries.

4PSSnet SLL
Content
Content 4
Safety instructions 5
Legend 9
1 Device description 10
1.1 Description of the device variants 10
2 Assembly and start-up 12
2.1 Installing the device 12
2.1.1 Unpacking and checking 12
2.1.2 Installing the SFP modules (if present) 13
2.1.3 Connecting the terminal block for the supply voltage and the
grounding 13
2.1.4 Mounting the device on the DIN rail 13
2.1.5 Dimensions 15
2.1.6 Installing the terminal block, start-up procedure 15
2.1.7 Connecting the data lines 15
2.2 Display elements 16
2.2.1 Device state 16
2.2.2 Port state 17
2.3 Disassembly 18
2.3.1 Removing the device from the DIN rail 18
3 Technical data 19
A Further support 23

PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany 5
Safety instructions
Notes on safety
This manual contains instructions to be observed for ensuring your per-
sonal safety and for preventing damage. The warnings appear next to a
warning triangle with a different heading depending on the degree of dan-
ger posed:
Danger!
Means that death, serious physical injury or significant damage
to property will occur if the corresponding safety measures are
not carried out.
Warning!
Means that death, serious physical injury or significant damage
to property could occur if the corresponding safety measures
are not carried out.
Caution!
Means that minor physical injury or damage to property can oc-
cur if the required safety measures are not carried out.
Note: Contains important information on the product, on how to manage
the product, or on the respective section of the documentation to which
your special attention is being drawn.
Certified usage
Please observe the following: The device may only be employed for the
purposes described in the catalog and technical description, and only in
conjunction with external devices and components recommended or
approved by the manufacturer. The product can only be operated cor-
rectly and safely if it is transported, stored, installed and assembled pro-
perly and correctly. Furthermore, it must be operated and serviced
carefully.
Supply voltage
The devices are designed for operation with a safety extra-low voltage.
Accordingly, only SELV circuits with voltage restrictions in line with IEC/
EN 60950-1 may be connected to the supply voltage connections.
Warning!
Only connect a supply voltage that corresponds to the type plate
of your device.
Use only undamaged parts.

6PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany
If you are operating the module with an external voltage, only supply
the system with a safety extra-low voltage in compliance with IEC/EN
60950-1.
Connect the ground connector before you set up the other connec-
tions. When removing the connections, you remove the ground con-
nector last.
Relevant for North America: To be used in class 2 circuits.
The device may only be connected to a supply voltage of class 2 that
fulfills the requirements of the National Electrical Code, Table 11(b).
Relevant for North America: For use in Class 2 circuits.
Only use copper wire/conductors of class 1, 60/75°C or 90 °C.
Relevant for North America
for devices certified for hazardous locations:
Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods [Article 501-4(b) of the National
Electrical Code, NFPA 70] and in accordance with the authority having
jurisdiction.
Only switch on the device when the housing is closed.
Shielding ground
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Housing
Only technicians authorized by Pilz are permitted to open the housing.
Note: The device is grounded by means of a 3-pin terminal block.
Make sure that the electrical installation meets local or nationally ap-
plicable safety regulations.
The ventilation slits must not be covered so as to ensure free air circu-
lation.
The clearance to the ventilation slits of the housing must be at least
10 cm (3.94 in).
The device must be installed in the vertical position.
If installed in a living area or office environment, the device must be op-
erated exclusively in switch cabinets with fire protection characteristics
in accordance with EN 60950-1.
Warning!
Never insert sharp objects (small screwdrivers, wires, etc.) into
the inside of the product. There is the risk of an electric shock.

PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany 7
Environment
The device may only be operated at the specified maximum ambient tem-
perature (temperature of the ambient air at a distance of up to 5 cm (1.97
in) from the device) and relative air humidity.
Install the device in a location where the climatic threshold values
specified in the technical data are adhered to.
Only to be used in an environment with the contamination level speci-
fied in the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and oper-
ation of this product and are appropriately qualified for their job. This in-
cludes, for example, those persons who have been:
Xtrained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
Xtrained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
Xtrained in providing first aid.
General safety instructions
Electricity is used to operate this equipment. Comply in every detail with
the safety requirements specified in the operating instructions regarding
the voltages to apply.
Non-observance of these safety instructions can therefore cause material
damage and/or serious injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. These personnel must be thoroughly familiar with all the
warnings and maintenance procedures in accordance with this oper-
ating manual.
The proper and safe operation of this device depends on proper han-
dling during transport, proper storage and assembly, and conscien-
tious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular, ob-
serve all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Relevant for PSSnet SLL....F..... with fiber optic ports.
Note:

8PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany
LED or LASER components in compliance with IEC 60825-1 (2001):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
Note on the CE marking
The devices comply with the regulations contained in the following Euro-
pean directive(s):
2006/95/EG, 2004/108/EG
Directive of the European Parliament and the council for standardizing
the regulations of member states with regard to electromagnetic
compatibility.
72/245/EWG, 2006/28/EG
Guideline for standardizing the regulations of member states relating to
radio interference from motor vehicles. Certified devices are marked with
an e1 type approval indicator.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the follow-
ing address:
Pilz GmbH & Co. KG
Felix Wankel Str. 2
73760 Ostfildern
Tel.: [phone]
The product can be used in living areas (living area, place of business,
small business) and in industrial areas.
XInterference immunity: EN 61000-6-2:2005
XEmitted interference: EN 55022:2006 Class A
Warning
This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to
take appropriate measures.
The assembly guidelines provided in these instructions must be strictly
adhered to in order to observe the EMC threshold values.

PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany 9
FCC note:
Appropriate testing has established that this device fulfills the require-
ments of a class A digital device in line with part 15 of the FCC regula-
tions.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can radiate same, and
if it is not installed and used in accordance with this operating manual, it
can cause radio transmission interference. The use of this device in a liv-
ing area can also cause interference, and in this case the user is obliged
to cover the costs of removing the interference.
Recycling note
After usage, this product must be disposed of properly as electronic waste
in accordance with the current disposal regulations of your county / state
/ country.
Legend
The commendations used in this manual have the following meanings:
XListing
Work step
Subheading

10 PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany
1 Device description
The PSSnet SLL devices are designed for the special requirements of indus-
trial automation. They meet the relevant industry standards, provide very
high operational reliability, even under extreme conditions, and also long-
term reliability and flexibility.
The devices allow you to set up switched industrial ETHERNET networks
that conform to the IEEE 802.3 and 802.3u standards using copper wires or
optical fibers in a line structure.
The PSSnet SLL devices have, depending on the variant, 4 or 5 TP ports (10/
100 Mbit/s, RJ45 socket) and one 100 Mbit/s F/O port (100BASE-FX SC con-
nection).
Mount the devices by
Xsimply snapping them onto a DIN rail
Depending on the device variant, you can choose various media to connect
terminal devices and other infrastructure components:
Xtwisted pair cable
Xmultimode F/O
The twisted pair ports support:
XAutocrossing
XAutonegotiation
XAutopolarity
The F/O ports support:
XFull duplex mode
1.1 Description of the device variants
The devices differ with regard to the number of interfaces and the media type
for connecting segments.
The table below shows the number and type of the ports for each product
variant. The abbreviations F/O (optical fiber) and TP (twisted pair) indicate
the media type. The abbreviations SC and RJ45 indicate the socket type. The
abbreviation MM (Multimode) indicate the optical fiber type.

PSSnet SLL
Pilz GmbH & Co. KG, Felix- Wankel- Straße 2, 73760 Ostfildern, Germany 11
Figure 1: Overview of the device PSSnet SLL 5T with 5 ports in compliance with 10/
100BASE-T(X) (RJ45 connections)
The following data applies in a cross-variant manner:
The devices comply with the specifications of the standard(s):
XISO/IEC 8802-03 10BASE-T/100BASE-TX
XISO/IEC 8802-03 100BASE-FX
Variant
10/100 Mbit/s, TP, RJ45 100 Mbit/s, F/O, MM, ST
PSSnet SLL 5T 5
PSSnet SLL 4T 1FMMSC 4 1
Table 1: Number and type of ports
Operating voltage 9.6 to 32.0 V DC
Software variant Unmanaged
Certifications / declarations pending UL508 (E175531)