Pivot PA-SK1 User manual

[Issued 2021.04.06]
SECURITY KIT
PA-SK-1 | Quick Introduction
For Use With Compatible PIVOT Cases

PA-SK1 | Quick Introduction
For Use With Compatible PIVOT Cases
The PIVOT Security Kit mitigates security concerns and minimizes the potential
for classified information compromised though the device cameras or
microphone. The PIVOT Security Kit includes sliding covers for the front and rear
cameras. The kit includes optional stickers than can be placed over the the front
camera. Additionally, the kit includes a microphone blocker that plugs into the
microphone opening on PIVOT cases.
Read Before Use
[Issued 2021.04.06] page: 02

PA-SK1 Overview:
PA-SS-1104
Security Stickers
PA-CB-2
Microphone Blocker
3.5mm
PA-MB-1
Large Sliding
Camera Blocker
PA-CB-1
Small Sliding
Camera Blocker
Large Sliding Camera Cover: Compatible with all PIVOT Cases that do NOT use a
front frame/bezel (e.g. PIVOT Mini Cases).
Rear Camera: Sliding Cover compatible with iPad models with a single rear
facing camera.
Security Stickers: All iPad models/PIVOT cases. Designed specifically for PIVOT
cases that use a front frame/bezel (e.g., PIVOT Mini cases).
Microphone Blocker compatible with any devices that have a 3.5mm headset
jack.
Depending on the device/case model, installation and removal may require
removing the device from the case.
Device Compatibility
[Issued 2021.04.06] page: 03

STEP 1: Clean camera surface and surrounding using manufacturer’s recommended methods.
STEP 2: Check for fit/compatibility with device and PIVOT case before final application.
STEP 3: Remove PA-CB-1 adhesive backing, align the hole on the sliding camera blocker with
device camera and lightly place blocker into position.
STEP 4: Test for proper function and adjust if necessary. Press firmly when complete.
PA-CB-1 Small Sliding Camera Blockers
!Pro Tip!
Is intended for use on rear facing cameras.
Remove adhesive backing
page: 04

STEP 1: Clean camera surface and surrounding using manufacturer’s recommended methods.
STEP 2: Check for fit/compatibility with device and PIVOT case before final application.
STEP 3: Remove PA-CB-2 adhesive backing, align the hole on the sliding camera blocker with
device camera and lightly place blocker into position.
STEP 4: Test for proper function and adjust if necessary. Press firmly when complete.
PA-CB-2 Large Sliding Camera Blockers
!Pro Tip!
Is intended for use on front facing cameras. Also remeber to adjust
ambient light sensor setting in the device menu after installing.
Remove adhesive backing
page: 05

STEP 1: The PA-MB-1 fits only standard 3.5mm headphone jacks.
STEP 2: Remove the audio block from the case.
STEP 3: Insert the PA-MA-1 into the audio jack of the device.
STEP 4: Remove the PA-MB-1 to restore microphone function. This may require first removing
the protective case depanding on device type and case.
PA-MB-2 Microphone Blockers, 3.5mm
page: 06

PA-SS-1104 Security Sticker
!Pro Tip!
Follow the instructions provided with your case or
locate instructions for your case at pivotcase.com
If the sliding camera blockers are not compatible with device or case, use PA-SS-1104 Security
Stickers.
STEP 1: Removing Device
Beginning with the bottom edge near the
charging port, press firmly using your
thumbs to disengage the case seal. Continue
carefully pressing around the edges of the
case to release the device in the order shown.
Do not attempt to pry or force the device from
the case.
1. Start at the bottom and move left
2. Continue around the top edge
3. Release the right edge to remove device
STEP 2: Put the stickers to cover the rear and front camera.
STEP 3: Installing Device
Align device camera and buttons with the corresponding access points in the case body
and press the corners of the device into the case in the order shown. The device will snap
securely into the case’s perimeter seal.
1
2
3
Top
Bottom
Left
Right
page: 07

If the sliding camera blockers are not compatible with device or case, use PA-SS-1104 Security
Stickers.
STEP 1: Removing Device
Beginning with the bottom edge near the
charging port, press firmly using your
thumbs to disengage the case seal. Continue
carefully pressing around the edges of the
case to release the device in the order shown.
Do not attempt to pry or force the device from
the case.
1. Start at the bottom and move left
2. Continue around the top edge
3. Release the right edge to remove device
STEP 2: Put the stickers to cover the rear and front camera.
STEP 3: Installing Device
Align device camera and buttons with the corresponding access points in the case body
and press the corners of the device into the case in the order shown. The device will snap
securely into the case’s perimeter seal.
!Pro Tip!
Press firmly around all edges of the front frame to engage the
locking tabs. When pressing each edge into a locked position.
Align device camera and buttons
To learn more about PIVOT cases, mounts and accessories, please visit
pivotcase.com for instructional videos, product support and information about
other PIVOT solutions. You’ll find valuable online resources provided to enhance
your user experience and see the complete line of PIVOT products.
Additional Information
1
1
3
2
4
page: 8

Thank you.
TM and © 2020 FlyBoys. All rights reserved.
Designed in USA. Printed in China.
Learn more at:
PIVOTCASE.COM
PIVOT SUPPORT
If you have questions please contact PIVOT Support.
[email protected]
www.pivotcase.com/support
1-888-4-FLYBOYS (1-888-435-9269)
www.youtube.com/c/pivotcasevideo
#EFBMADESIMPLE
@PIVOTCASE