Planet GSD-604HP User manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
GSD-604HP User's Manual 55V Power Adapter
Power Cord Rubber Feet Wall-mount Kit
x 4
5. Switch Rear Panel
Figure 5-1 shows the rear panel of GSD-604HP.
55V DC
DisableEnable
Port-based VLAN & Loop protection
Please power off before switching DIP.
Figure 5-1: GSD-604HP Rear Panel
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some areas, installing a surge sup-
pression device may also help to protect
your GSD-604HP from being damaged
by unregulated surge or current to the
GSD-604HP or the power adapter
2. Product Features
RJ45 Interface
6 10/100/1000Mbps Gigabit Ethernet ports
4 ports support 54V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span PSE
Up to 4 IEEE 802.3af/802.3at devices powered
Supports PoE power up to 30 watts for each PoE
port
55-watt PoE Budget
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m
Hardware
LED indicators for PoE ready/activity and LINK/ACT
One 55V DC power jack
Switching
Hardware based 10/100/1000Mbps auto-negotiation
and auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
9216 bytes jumbo packet size support
Integrates address look-up engine, supporting 8K
absolute MAC addresses
Automatic address learning and address aging
Supports port-based VLAN and loop protection
3. Switch Front Panel
Figure 3-1 shows the front panel of GSD-604HP.
PWR
PoE MAX
PoE In-Use
1 2 3 4
GSD-604HP 5
Uplink
41 2 3 6
PoE
ACT
1000 LNK
ACT
10/100 LNK
Figure 3-1: GSD-604HP Front Panel
6. Port-based VLAN and Loop
Protection Feature
The GSD-604HP has one feature called Port-based
VLAN and Loop Protection. When switching the DIP to
the “Enable”position, port 1 to port 5 wouldn’t able to
communicate with each other.
PWR
PoE MAX
PoE In-Use
1 2 3 4
GSD-604HP 5
Uplink
41 2 3 6
PoE
ACT
1000 LNK
ACT
10/100 LNK
Port 1 to Port 5 only can communicate with Uplink Port 6.
PWR
PoE MAX
PoE In-Use
1 2 3 4
GSD-604HP 5
Uplink
41 2 3 6
PoE
ACT
1000 LNK
ACT
10/100 LNK
When there is a loop happening from the client, the
GSD-604HP will block that port and wouldn’t allow data
to transfer to the switch.
PWR
PoE MAX
PoE In-Use
1 2 3 4
GSD-604HP 5
Uplink
41 2 3 6
PoE
ACT
1000 LNK
ACT
10/100 LNK
Loop (broadcast)
4. LED Indicators
System
LED Color Function
PWR Green Lights: Indicates the Switch has
power.
Per 10/100/1000Mbps Port
LED Color Function
1000
LNK Green
Lights: Indicates the link through
that port is successfully
established at 1000Mbps.
Blinks: Indicates that the Switch is
actively sending or receiving
data over that port.
10/100
LNK Orange
Lights: Indicates the link through
that port is successfully
established at 10/100Mbps.
Blinks: Indicates that the Switch is
actively sending or receiving
data over that port.
PoE-in-Use Port
LED Color Function
PoE Orange Lights: Indicates the port is providing
54V DC in-line power.
MAX Orange Lights: 80% of PoE usage
Blinks: 100% of PoE usage
7. Installing the Switch
This part describes how to install your Gigabit PoE+
Switch and make connections to it. Please read the
following topics and follow the procedures as presented.
Note
This Gigabit PoE+ Switch does not need
software configuration.
Desktop Installation
To install the Gigabit PoE+ Switch on desktop, simply
follow the following steps:
Step 1: Attach the rubber feet to the recessed areas
on the bottom of the Gigabit PoE+ Switch.
Step 2: Place the Gigabit PoE+ Switch on desktop near
AC power source for its power adapter.
Step 3: Keep enough ventilation space between the
Gigabit PoE+ Switch and the surrounding
objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 8 -- Product Specifica-
tions.
Step 4: Connect your Gigabit PoE+ Switch to network
devices.
A. Connect one end of a standard network cable to
port-5 and port-6 10/100/1000Mbps RJ45 ports on
the front of the Gigabit PoE+ Switch.
B. Connect the other end of the cable to the network
devices such as NVR(Network Video Recorder),
workstations or routers.
Step 5: Connect your Gigabit PoE+ Switch to PoE PD
devices.
A. Connect one end of a standard network cable to port
1 to port 4 10/100/1000Mbps RJ45 ports on the
Front of the Gigabit PoE+ Switch.
B. Connect the other end of the cable to the 802.3at/
af powered devices.
Power
GSD-604HP
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line
Port 1~Port 4 PoE IP Cameras
Port 5~Port 6 Dual Uplink Ports
PoE PoE PoE PoE
4 Channel NVR

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
Note
Cable Distance for Switch
The cable distance between the GSD-604HP
and PC/PD devices should not exceed 100
meters for UTP/STP cable.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used for
10/100Mbps operation. To reliably operate
your network at 1000Mbps, you must use
an Unshielded Twisted-Pair (UTP) Category
5/5e cable, or better data grade cabling.
While a Category 3 or 4 cable may initially
seem to work, it will soon cause data loss.
Step 6: Supply power to the Gigabit PoE+ Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the Gigabit PoE+ Switch receives power, the
Power LED should remain solid Green.
Wall-mount Installation
Step 1: Please nd the wall that can mount the
GSD-604HP.
Step 2: Install four screws on the wall.
8. Product Specications
Model
GSD-604HP
4-Port 10/100/1000T 802.3at
PoE + 2-Port 10/100/1000T
Desktop Switch
HardwareSpecications
Network Connector
6-Port RJ45 for
10/100/1000BASE-T, auto MDI/
MDIX
PoE Inject Port
4-Port with 802.3af/at PoE
injector function (port 1 to port
4)
LED Display
System: Power (Green)
Per PoE port:
PoE (Orange, port 1 to port 4)
PoE MAX (Orange)
Ethernet port:
1000 LNK (Green)
10/100 LNK (Orange)
Switch Architecture Store and Forward switch
architecture
Thermal Fan Fanless design
MAC Address Table 8K MAC address table with auto
learning function
Switch Fabric 12Gbps
Step 3: Hang the GSD-604HP on the screws from the
wall.
Step 4: Repeat step 6 of Desktop Installation for
power supply to the GSD-604HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
RJ45
UTP Cable
Switch Throughput 8.92Mpps @64 bytes
Jumbo Packet 9216 bytes
Flow Control
Back pressure for half-duplex.
IEEE 802.3x pause frame for
full-duplex
Power Requirements 55V DC, 1.1A
ESD Protection 6KV DC
Power Consumption Max. 60 watts, 204.6 BTU
Dimensions
(W x D x H) 160 x 92.5 x 28mm
Weight 374g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over
Ethernet/PSE
IEEE 802.3at Power over
Ethernet Plus/PSE
PoE Power Supply
Type End-span
Power Pin
Assignment 1/2(+), 3/6(-)
PoE Power Output
Per Port 54V DC, 300mA. max.
15.4 watts (IEEE 802.3af)
Per Port 54V DC, 600mA. max.
30 watts (IEEE 802.3at)
PoE Power Budget 55 watts
Standard Conformance
EMI Safety FCC Class B, CE
Standard
Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Power over
Ethernet
Power over
Ethernet Plus
Environment
Operating
Environment 0 ~ 50 degrees C
Storage
Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
9. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.