Planet GSW-1601 User manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port
10/100/1000BASE-T Unmanaged Gigabit Ethernet Switch,
GSW-1601/GSW-2401. “Gigabit Ethernet Switch”
mentioned in this User’s Manual refers to the GSW-1601/
GSW-2401.
Open the box of the Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Gigabit Ethernet Switch x 1 Power Cord x 1
Accessories x 1 User’s Manual x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
Hardware Features
z100~240V AC, 0.5A, 50~60Hz universal power input
(GSW-1601)
z100~240V AC, 0.8A, 50~60Hz universal power input
(GSW-2401)
zFCC, CE class A compliant
3. Product Specications
Product GSW-1601 GSW-2401
Hardware Specications
Hardware Version 8
10/100/1000BASE-T
MDI/MDIX Ports 16 24
Throughput
(packet per second) 23.8Mpps 35.7Mpps
Switch Fabric 32Gbps 48Gbps
Weight 1.4kg 1.5kg
Power Consumption/
Dissipation
8.6 watts/
29 BTU
15.7 watts/
53 BTU
Power Requirements 100~240V AC,
0.5A, 50-60Hz
100~240V AC,
0.8A, 50-60Hz
5. Switch Rear Panel
Figure 3 shows the rear panel of the GSW-1601/GSW-2401
100~240V AC
50 / 60Hz
Figure 3: GSW-1601/GSW-2401 Rear Panel
Power
Note
1.The device is a power-required device,
meaning it will not work till it is powered. If
your network should be active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will prevent
you from network data loss or network
downtime.
2.In some areas, installing a surge suppression
device may also help to protect your Gigabit
Ethernet Switch from being damaged by
unregulated surge or current to the Switch or
the power adapter.
4. Switch Front Panel
Figures 1 & 2 show the front panels of the GSW-1601 and
GSW-2401.
16-Port 10/100/1000T Gigabit Ethernet Switch
GSW-1601
ACT1000 LNK
ACT10/100LNK
1 3 5 7 9 11 13 15
PWR 2 4 6 8 10 12 14 16
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
Figure 1: GSW-1601 Front Panel
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1357911 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 2: GSW-2401 Front Panel
2. Product Features
Physical Port
z16/24 10/100/1000BASE-T Gigabit Ethernet ports
zSupports auto MDI/MDI-X function
Layer 2 Features
zComplies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet stan-
dards
zFeatures Store-and-Forward mode with wire-speed
ltering and forwarding rates
zIntegrated address look-up engine, supporting 8K abso-
lute MAC addresses
z9K jumbo packet support
zPower saving ability for Green networking
zIEEE 802.1Q VLAN packet transparency support
zIEEE 802.3x ow control for full duplex operation and
back pressure for half duplex operation
zHardware-based 10/100BASE-TX, half/full duplex and
1000BASE-T full duplex mode, ow control and auto-
negotiation
zAutomatic address learning and address aging
zSupports CSMA/CD protocol
Dimensions
(W x D x H) 440 x 210 x 44mm, 1U height
Switch Processing
Scheme Store-and-Forward
Address Table 8K entries
Jumbo Packet Size 9K
Flow Control Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity
Operating: 5% to 95%
(non-condensing)
Storage: 5% to 95%
(non-condensing)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3x (Full-Duplex Flow
Control)
IEEE 802.3az Energy Ecient
Ethernet (EEE)
LED Indicators
GSW-1601/GSW-2401
System
LED Color Function
PWR Green Lights: to indicate that the Switch
has power.
Per 10/100/1000BASE-T Port
LED Color Function
10/100
LNK/ACT Orange
Lights: to indicate the link through
that port is established
successfully at 10/100Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
1000
LNK/ACT Green
Lights: to indicate the link through
that port is established
successfully at 1000Mbps.
Blinks: to indicate that the Switch is
actively sending or receiving
data over that port.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 4 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 4: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 5.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Figure 5: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2019
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 16-/24-Port 10/100/1000Mbps Gigabit Ethernet Switch
*Model Number : GSW-1601, GSW-2401
* Produced by:
Manufacturer‘s Name :Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU; Low Voltage Directive 2014/35/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)
EN 60950-1 (2006+A11:2009+A1:2010+A12:2011+A2: 2013)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
April 30, 2019
Place
Date
Legal Signature