Planet IGS-1020PTF Series User manual

Industrial 8-Port 10/100/1000T 802.3at PoE +
2-Port 100/1000X SFP Ethernet Switch
IGS-1020PTF Series
User’s Manual

Table of Contents
1. Package Contents................................................................................. 3
2. Hardware Introduction .......................................................................... 4
2.1 Switch Front Panel......................................................................... 4
2.2 LED Indicators............................................................................... 6
2.3 Switch Upper Panel........................................................................ 7
2.4 Wiring the Power Inputs................................................................. 8
2.5 Wiring the Fault Alarm Contact ....................................................... 9
2.6 Grounding the Device................................................................... 10
3. Installation ........................................................................................ 11
3.1 DIN-rail Mounting Installation ....................................................... 11
3.2 Wall-mount Plate Mounting ........................................................... 12
3.3 Side Wall-mount Plate Mounting (for IGS-1020PTF only) ................. 12
4. ProductSpecications ......................................................................... 13
Customer Support.................................................................................... 16

3
1. Package Contents
Thank you for purchasing PLANET Industrial 8-port 10/100/1000T 802.3at PoE
+ 2-port 100/1000X SFP Ethernet Switch, IGS-1020PTF or IGS-1020PTF-12V.
Thehardwarespecicationsofthesemodelsareshownbelow:
Model Name 10/100/1000T 802.3at
PoE+ RJ45 Ports
100/1000X
SFP Slots
Power Input
Range
IGS-1020PTF 8 2 DC 48~54V
IGS-1020PTF-12V DC 12~54V
In the following sections, the term “Industrial PoE+ Switch” means the
IGS-1020PTF or IGS-1020PTF-12V.
Open the box of the Industrial PoE+ Switch and carefully unpack it. The box
shouldcontainthefollowing items:
IndustrialPoE+Switchx1 QRcodesheetx1 SFPDustCapsx2
Wall-mountkitx1 DIN-railkitx1 RJ45DustCapsx8
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a need to
return it to us for repair.

4
2. Hardware Introduction
2.1 Switch Front Panel
The front panels of the Industrial PoE+ Switches consist of Ethernet interfaces
andLEDindicatorsasshownbelow:
9 10
910
100/1000X SFP
LNK ACT
1000
10/100/1000T
IGS-1020PTF
6
4
2
7
5
3
1
8
LNK
ACT
PoE-in-Use
802.3at PoE+
P1 P2 Alarm
240W
PoE Usage
180W
120W
60W
Standard
Extend (Ports 5~8)
Mode
9 10
910
100/1000X SFP
LNK ACT
1000
10/100/1000T
IGS-1020PTF-12V
6
4
2
7
5
3
1
8
LNK
ACT
PoE-in-Use
802.3at PoE+
P1 P2 Alarm
240W
PoE Usage
180W
120W
60W
Standard Extend (Ports 5~8)
Mode
Figure 2-1: IGS-1020PTF front
panel
Figure 2-2: IGS-1020PTF-12V
front panel
GigabitTPInterfaces(Port1toPort8)
10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters in standard
mode.
GigabitSFPSlots(Port9toPort10)
100/1000BASE-X mini-GBIC slot, SFP (small factor pluggable) transceiver
module: From 550 meters to 2 kilometers (multi-mode ber) and up to
10/20/40/60/80/120kilometers(single-modeberorWDMber).
DIP Switch for Port 5 to Port 8
The Industrial PoE+ Switch has a built-in solid DIP switch that provides
“Standard” and “Extend” operation modes. The Industrial PoE+ Switch
operates as a normal IEEE 802.af/at PoE+ Switch in the “Standard” operation
mode.

5
In the “Extend” operation mode, Port 5 to Port 8 of the Industrial PoE+
Switch operate on a per-port basis at 10Mbps full duplex operation but can
support 20~25-watt PoE power output over a distance of up to 250 meters
overcoming the 100m limit on Ethernet UTP cable. With this feature, the
Industrial PoE+ Switch provides an additional solution for 802.3af/at PoE+
distanceextension.
Standard Mode (default)
PoE IP Camera
PoE
100 meters (328 feet)
PoE
100BASE-TX UTP with PoE
IGS-1020PTF
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
Extended Mode
PoE
250 meters (820 feet)
PoE
10BASE-T UTP with PoE
PoE IP Camera
IGS-1020PTF
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
DIP Switch Mode Function
Standard
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
DIP switch is o
This mode makes the Industrial PoE+ Switch operate
as a general switch and all PoE ports operate at
10/100/1000Mbpsauto-negotiation.
Extended
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
DIP switch is on
This mode makes Port 5 to Port 8 of the Industrial PoE+
Switchoperateonaper-portbasisat10Mbpsfullduplex
operationbutcansupportPoEpower outputovera
distance of up to 250 meters overcoming the 100m limit
onEthernetUTPcable.

6
AfterchangingtheDIPswitch mode,pleasereboottheswitchto
take effect.
2.2 LED Indicators
System
LED Color Function
P1 Green Lights: Indicates power 1 has power.
P2 Green Lights: Indicates power 2 has power.
Alarm Red Lights: Indicates either power 1 or power 2 has no power.
60W Amber
O: Indicates the PoE usage is less than 30W.
Blinks: Indicates that the PoE usage is around 30W to
59W.
Lights: Indicates the PoE usage is around/over 60W.
120W Amber
Blinks: Indicates that the PoE usage is around 60W to
119W.
Lights: Indicates the PoE usage is around/over 120W.
180W Amber
Blinks: Indicates that the PoE usage is around 120W to
179W.
Lights: Indicates the PoE usage is around/over 180W.
240W Amber
Blinks: Indicates that the PoE usage is around 180W to
239W.
Lights:IndicatesthePoEusageisatthemaximum.
Per 802.3at PoE+ 10/100/1000BASE-T Interface (Port 1 to Port 8)
LED Color Function
LNK/
ACT Green
Lights: Indicates the link through that port is successfully
establishedat10Mbps,100Mbpsor1000Mbps.
Blinks: Indicates that the switch is actively sending or
receiving data over that port.
PoE -
in-Use Amber
Lights: Indicates the port is providing DC in-line power.
O: Indicates the connected device is not a PoE powered
device (PD).

7
Per 100/1000X SFP Slot (Port 9 to Port 10)
LED Color Function
LNK/
ACT Green
Lights: Indicates the link through that port is successfully
establishedat1000Mbpsor100Mbps.
Blinks: Indicates that the switch is actively sending or
receiving data over that port.
1000 Amber
Lights: Indicates the link through that port is successfully
establishedat1000Mbps.
O:Indicatesthelinkthroughthatportisnotestablished
orisestablishedat100Mbps.
2.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one terminal block
connector within two power input and one relay output.
Figure 2-3 shows the upper panel of the IGS-1020PTF.
PWR1 PWR2
Alarm
DC Input:
48-54V , 7A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Figure 2-3: IGS-1020PTF Upper Panel
Figure 2-4 shows the upper panel of the IGS-1020PTF-12V.
PWR1 PWR2
Alarm
DC Input:
12-54V , 7A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Figure 2-4: IGS-1020PTF-12V Upper Panel

8
2.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial PoE+
Switch is used for two DC redundant power inputs. Please follow the steps
belowtoinsertthepowerwire.
When performing any of the procedures like inserting the wires
or tightening the wire-clamp screws, make sure the power is
OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into Contacts 1 and 2 for
Power 1, or Contacts 5 and 6 for Power 2.
PWR1 PWR2
Alarm
DC Input:
48-54V , 7A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
Power 1 Alarm Power 2
+ - + -

9
1.The wire gauge for the terminal block should be in the range
between12and24AWG.
2. The IGS-1020PTF-12V supports DC input range of 12V
to 54V. To avoid damage, please use the IGS-1020PTF-12V
underitsspecication.
DC Input Max.PoEBudget
12V 60W
24V 120W
54V 240W
3. PWR1 and PWR2 must provide the same DC voltage while
operating with dual power input.
2.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as
the picture shows below. Inserting the wires, the Industrial PoE+ Switch will
detect the alarm status of the power failure and then forms an open circuit.
The following illustration shows an application example for wiring the fault
alarm contacts.
Fault Alarm Contacts
Alarm
The Fault Alarm Contacts are
energized (CLOSE) for
normal operation and will
OPEN when failure occurs
Insert the wires into the fault alarm contacts

10
1.The wire gauge for the terminal block should be in the range
between12and24AWG.
2.Alarmrelaycircuitacceptsupto24Vwithamaximumcurrent
of 1A.
2.6 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
PWR1 PWR2
Alarm
DC Input:
48-54V , 7A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
Earth Ground
EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.