Planet IGS-5225-4T2S User manual

Industrial L2+ Multi-Port Full Gigabit
Managed Ethernet Switch
IGS-5225-4T2S/IGS-5225-4UP1T2S
IGS-5225-8P2S/IGS-5225-8P4S/IGS-5225-8P2T2S
Quick Installation Guide

Table of Contents
1. Package Contents...................................................................... 3
2. Requirements............................................................................ 5
3. Wiring the Power Inputs ............................................................ 6
4. Terminal Setup.......................................................................... 8
5. Logging on to the Console ......................................................... 9
6. ConguringIPaddress..............................................................11
7. Starting Web Management ........................................................14
8. SavingCongurationvia Web ....................................................17
9. Resetting the Switch to Default .................................................18
10. Customer Support....................................................................20

3
1. Package Contents
Thank you for purchasing PLANET L2+ Industrial Managed Switch,
IGS-5225Series.Thedescriptionsofthesemodelsareasfollows:
IGS-5225-4T2S: IndustrialL2+4-Port10/100/1000T+2-Port
100/1000XSFPManagedSwitch
IGS-5225-4UP1T2S:
IndustrialL2+4-Port10/100/1000TUltraPoE+
1-Port10/100/1000T+2-Port100/1000XSFP
ManagedSwitch
IGS-5225-8P2S:
IndustrialL2+8-Port10/100/1000T802.3at
PoE+2-Port100/1000XSFPManagedEthernet
Switch
IGS-5225-8P4S:
IndustrialL2+8-Port10/100/1000T802.3at
PoE+4-Port100/1000XSFPManagedEthernet
Switch
IGS-5225-8P2T2S:
IndustrialL2+8-Port10/100/1000T802.3at
PoE+2-Port10/100/1000T+2-Port
100/1000XSFPManagedEthernetSwitch
“Industrial Managed Switch” mentioned in this Quick Installation
Guidereferstotheabovevemodels.

4
Open the box of the Industrial Managed Switch and carefully
unpackit.Theboxshouldcontainthefollowingitems:
zTheIndustrialManagedSwitchx1
zQuickInstallationGuidex1
zDIN-rail Kit x 1
zWall Mounting Kit x 1
zDB9 to RJ45 Interface RS232 Console Cable x 1
zDust Cap (Please refer to the table below.)
RJ45 Dust Cap SFPDustCap
IGS-5225-4T2S 5 2
IGS-5225-8P2S 9 2
IGS-5225-8P4S 9 4
IGS-5225-8P2T2S 11 2
IGS-5225-4UP1T2S 6 2
If any of these are missing or damaged, please contact your dealer
immediately. If possible, retain the carton includingtheoriginalpacking
materials to enable you to repack the product in case there is a need
to return it to us for repair.

5
2. Requirements
The Industrial Managed Switch provides remote login interface for
management purposes. The following equipment is necessary for
furthermanagement:
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC
OS X or later, Linux, UNIX, or other platforms are compatible with
TCP/IPProtocols.
zWorkstations are installed with Ethernet NIC (Network Interface
Card)
zSerial Port Connection (Terminal)
The above Workstations come with COM Port (DB9) or USB-to-
RS232 converter.
The above Workstations have been installed with terminal
emulator, such as Hyper Terminal included in Windows XP/2003,
putty or tera term.
Serial cable -- one end is attached to the RS232 serial port,
while the other end to the console port of the Industrial Managed
Switch.
zEthernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
The above PC is installed with Web browser and JAVA runtime
environment plug-in.
Note
Itis recommended to use InternetExplorer8.0or above
toaccesstheIndustrialManagedSwitch.

6
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch comes with a DC
inlet power socket and one 6-contact terminal block. Please follow the
steps below to insert the power wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for
Power1,orContacts5and6forPower2.
IGS-5225-8P2S/IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-
5225-4UP1T2S: 48~56VDC
Input DC 48-56V
DI0 DI1 DO0 DO1 GND GND
DC1
+
DC2Fault
+
1A@24V
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-5225-8P2S/IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-
4UP1T2S Upper Panel
IGS-5225-4T2S:12~48VDC,24VAC
Input
DC12~48V
AC 24V
DC1 DC2
Fault
V1-V1+ V2+ V2-1A@24V
1 2 3 4 5 6
Figure 3-2: IGS-5225-4T2S Upper Panel

7
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
123456
V+ V- V+ V-
Power 1 Power 2
Positive (+) Pin Negative (-) Pin
IGS-5225 Series Pin1/5 Pin2/6
Note
The wire gauge for the terminal block should be in the
range from 12 to 24 AWG.

8
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a
PC or notebook computer and to RJ45 type serial (console) port of the
Industrial Managed Switch. The console port of the Industrial Managed
Switch is DCE already, so that you can connect the console port
directlythroughPCwithouttheneedofnullmodem.
PC/Workstation
with
Terminal emulation software
RJ45 to DB9 RS232 Cable
Serial Port
IP Address:
192.168.0.100
IGS Industrial Managed Switch
A terminal program is required to make the software connected to the
IGS-5225seriesIndustrialManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port
shouldbeconguredas:
zBaud:115200
zParity:None
zDatabits:8
zStopbits:1
zFlowcontrol:None

9
5. Logging on to the Console
Once the terminal has been connected to the device, power on the
IndustrialManagedSwitchandtheterminalwilldisplay“running testing
procedures”.
Note
The following terminal configuration of IGS-5225-8P4S is
taken for an example.
Then, the following message asks to log in user name and password.
The default user name and password are shown as follows and the
loginscreeninFigure5-1appears
Username:admin
Password: admin
Figure 5-1: Console Login Screen

10
The user can now enter commands to manage the Industrial Managed
Switch. For a detailed description of the commands, please refer to the
following chapters.
Note
1. For security reason, please change and memorize
the new password after this first setup.
2. Only accept command in lowercase letter under
console interface.