Planet IGS-4215-4P4Tv2 User manual

User’s Manual of IGS-4215 PoE Series
1
Industrial L2/L4
Managed Gigabit PoE Switch
IGS-4215 PoE Series

User’s Manual of IGS-4215 PoE Series
2
Trademarks
Copyright © PLANET Technology Corp. 2023.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANETmakes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
This device is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the power cable to
disconnect the device from the power circuit. In view of saving the energy and reducing the unnecessary power consumption, it
is strongly suggested to remove the power connection for the device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
PLANET IGS-4215 PoE Series User's Manual
MODELS: IGS-4215-4P4Tv2/IGS-4215-4P4T2Sv2/IGS-4215-8P2T2Sv2/IGS-4215-4UP4T2S/IGS-4215-8UP2T2S
REVISION: 1.3 (January, 2023)
Part No: EM-IGS-4215-PoE series_v1.3

User’s Manual of IGS-4215 PoE Series
3
TABLE OF CONTENTS
1. INTRODUCTION .................................................................................................................... 9
1.1 Packet Contents ............................................................................................................................................. 9
1.2 Product Description ..................................................................................................................................... 10
1.3 How to Use This Manual .............................................................................................................................. 16
1.4 Product Features ......................................................................................................................................... 17
1.5 Product Specifications ................................................................................................................................ 20
2. INSTALLATION ................................................................................................................... 25
2.1 Hardware Description .................................................................................................................................. 25
2.1.1 Physical Dimensions.............................................................................................................................................26
2.1.2 Switch Front Panel................................................................................................................................................29
2.1.3 LED Indications.....................................................................................................................................................31
2.1.4 Switch Upper Panel...............................................................................................................................................37
2.1.5 Wiring the Power Inputs........................................................................................................................................38
2.1.6 Wiring the Faulty Alarm Contact............................................................................................................................39
2.2 Installing the Industrial Managed Switch .................................................................................................. 40
2.2.1 Installation Steps...................................................................................................................................................40
2.2.2 DIN-rail Mounting ..................................................................................................................................................41
2.2.3 Wall-mount Plate Mounting ...................................................................................................................................43
2.2.4 Installing the SFP Transceiver...............................................................................................................................44
2.2.5 Removing the SFP Transceiver.............................................................................................................................47
3. SWITCH MANAGEMENT .................................................................................................... 48
3.1 Requirements ............................................................................................................................................... 48
3.2 Management Access Overview .................................................................................................................. 49
3.3 Administration Console .............................................................................................................................. 50
3.4 Web Management ........................................................................................................................................ 51
3.5 SNMP-based Network Management ........................................................................................................... 52
3.6 PLANET Smart Discovery Utility ................................................................................................................ 52
4. WEB CONFIGURATION ...................................................................................................... 54
4.1 Main Web Page ............................................................................................................................................. 57
4.1.1 Save Button...........................................................................................................................................................59
4.1.2 Configuration Manager..........................................................................................................................................59
4.1.2.1 Saving Configuration..........................................................................................................................................60
4.2 System .......................................................................................................................................................... 61
4.2.1 System Information ...............................................................................................................................................61
4.2.2 IP Configurations...................................................................................................................................................63
4.2.3 IPv6 Configuration.................................................................................................................................................65
4.2.4 User Configuration ................................................................................................................................................67
4.2.5 Time Settings.........................................................................................................................................................68
4.2.5.1 System Time.......................................................................................................................................................68
4.2.5.2 SNTP Server Settings........................................................................................................................................71
4.2.6 Log Management ..................................................................................................................................................72
4.2.6.1 Local Log............................................................................................................................................................72

User’s Manual of IGS-4215 PoE Series
4
4.2.6.2 Local Log............................................................................................................................................................73
4.2.6.3 Remote Syslog...................................................................................................................................................74
4.2.6.4 Log Message......................................................................................................................................................76
4.2.7 SNMP Management..............................................................................................................................................78
4.2.7.1 SNMP Overview.................................................................................................................................................78
4.2.7.2 SNMP Setting.....................................................................................................................................................79
4.2.7.3 SNMP View ........................................................................................................................................................80
4.2.7.4 SNMP Access Group..........................................................................................................................................81
4.2.7.5 SNMP Community..............................................................................................................................................82
4.2.7.6 SNMP User ........................................................................................................................................................84
4.2.7.7 SNMPv1, 2 Notification Recipients.....................................................................................................................86
4.2.7.8 SNMPv3 Notification Recipients.........................................................................................................................87
4.2.7.9 SNMP Engine ID................................................................................................................................................89
4.2.7.10 SNMP Remote Engine ID.................................................................................................................................90
4.2.8 RMON ...................................................................................................................................................................91
4.2.8.1 RMON Statistics.................................................................................................................................................91
4.2.8.2 RMON Event......................................................................................................................................................93
4.2.8.3 RMON Event Log...............................................................................................................................................94
4.2.8.4 RMON Alarm......................................................................................................................................................95
4.2.8.5 RMON History....................................................................................................................................................98
4.2.8.6 RMON History Log.............................................................................................................................................99
4.2.9 Fault Alarm Configuration....................................................................................................................................100
4.2.10 Remote Management........................................................................................................................................101
4.3 Port Management ....................................................................................................................................... 103
4.3.1 Port Configuration ...............................................................................................................................................103
4.3.2 Port Counters......................................................................................................................................................105
4.3.3 Bandwidth Utilization...........................................................................................................................................109
4.3.4 Port Mirroring.......................................................................................................................................................110
4.3.5 Jumbo Frame......................................................................................................................................................112
4.3.6 Port Error Disabled Configuration........................................................................................................................113
4.3.7 Port Error Disabled Status...................................................................................................................................115
4.3.8 Protected Ports....................................................................................................................................................116
4.3.9 EEE.....................................................................................................................................................................118
4.3.10 SFP Module Information....................................................................................................................................120
4.3.10.1 SFP Module Status ........................................................................................................................................120
4.3.10.2 SFP Module Detail Status..............................................................................................................................122
4.4 Link Aggregation ........................................................................................................................................ 123
4.4.1 LAG Setting.........................................................................................................................................................125
4.4.2 LAG Management...............................................................................................................................................126
4.4.3 LAG Port Setting .................................................................................................................................................127
4.4.4 LACP Setting.......................................................................................................................................................129
4.4.5 LACP Port Setting...............................................................................................................................................130
4.4.6 LAG Status..........................................................................................................................................................131

User’s Manual of IGS-4215 PoE Series
5
4.5.1 VLAN Overview...................................................................................................................................................133
4.5.2 IEEE 802.1Q VLAN.............................................................................................................................................134
4.5.3 Management VLAN.............................................................................................................................................138
4.5.4 Create VLAN.......................................................................................................................................................139
4.5.5 Interface Settings ................................................................................................................................................140
4.5.6 Port to VLAN.......................................................................................................................................................144
4.5.7 Port VLAN Membership.......................................................................................................................................145
4.5.8 Protocol VLAN Group Setting..............................................................................................................................146
4.5.9 Protocol VLAN Port Setting.................................................................................................................................148
4.5.10 GVRP Setting....................................................................................................................................................149
4.5.11 GVRP Port Setting.............................................................................................................................................151
4.5.12 GVRP VLAN......................................................................................................................................................152
4.5.13 GVRP Statistics.................................................................................................................................................153
4.5.14 VLAN Setting Example:.....................................................................................................................................155
4.5.14.1 Two Separate 802.1Q VLANs ........................................................................................................................155
4.5.14.2 VLAN Trunking between two 802.1Q aware switches....................................................................................158
4.6 Spanning Tree Protocol ............................................................................................................................. 161
4.6.1 Theory.................................................................................................................................................................161
4.6.2 STP Global Settings............................................................................................................................................168
4.6.3 STP Port Setting..................................................................................................................................................170
4.6.4 CIST Instance Setting .........................................................................................................................................173
4.6.5 CIST Port Setting ................................................................................................................................................175
4.6.6 MST Instance Configuration................................................................................................................................177
4.6.7 MST Port Setting.................................................................................................................................................179
4.6.8 STP Statistics......................................................................................................................................................181
4.7 Multicast...................................................................................................................................................... 181
4.7.1 Properties............................................................................................................................................................182
4.7.2 Multicast Throttling Setting..................................................................................................................................183
4.7.3 Multicast Profile Setting.......................................................................................................................................184
4.8 IGMP Snooping .......................................................................................................................................... 186
4.8.1 IGMP Setting.......................................................................................................................................................190
4.8.2 IGMP Querier Setting..........................................................................................................................................192
4.8.3 IGMP Static Group..............................................................................................................................................193
4.8.4 IGMP Group Table...............................................................................................................................................194
4.8.5 IGMP Router Setting...........................................................................................................................................194
4.8.6 IGMP Router Table..............................................................................................................................................196
4.8.7 IGMP Forward All................................................................................................................................................197
4.8.8 IGMP Snooping Statics .......................................................................................................................................198
4.8.9 IGMP Filter Setting..............................................................................................................................................200
4.9 MLD Snooping ............................................................................................................................................ 201
4.9.1 MLD Setting.........................................................................................................................................................201
4.9.2 MLD Static Group................................................................................................................................................203
4.9.3 MLD Group Table................................................................................................................................................204
4.9.4 MLD Router Setting.............................................................................................................................................204
4.9.5 MLD Router Table ...............................................................................................................................................206
4.9.6 MLD Forward All..................................................................................................................................................207

User’s Manual of IGS-4215 PoE Series
6
4.9.7 MLD Snooping Statics.........................................................................................................................................208
4.9.8 MLD Filter Setting................................................................................................................................................209
4.10.1 Link Layer Discovery Protocol...........................................................................................................................210
4.10.2 LLDP Global Setting..........................................................................................................................................211
4.10.3 LLDP Port Setting..............................................................................................................................................213
4.10.4 LLDP Local Device............................................................................................................................................216
4.10.5 LLDP Remote Device........................................................................................................................................217
4.10.6 MED Network Policy..........................................................................................................................................218
4.10.7 MED Port Setting...............................................................................................................................................221
4.10.8 LLDP Statistics..................................................................................................................................................224
4.11 MAC Address Table .................................................................................................................................. 226
4.11.1 Dynamic Learned ..............................................................................................................................................226
4.11.2 Dynamic Address Setting...................................................................................................................................228
4.11.3 Static MAC Setting ............................................................................................................................................229
4.11.4 MAC Filtering.....................................................................................................................................................230
4.12 Quality of Service ..................................................................................................................................... 231
4.12.1 Understanding QoS...........................................................................................................................................231
4.12.2 General .............................................................................................................................................................232
4.12.2.1 QoS Properties...............................................................................................................................................232
4.12.2.2 QoS Port Settings...........................................................................................................................................233
4.12.2.3 Queue Settings...............................................................................................................................................234
4.12.2.4 CoS Mapping..................................................................................................................................................235
4.12.2.5 DSCP Mapping...............................................................................................................................................237
4.12.2.6 IP Precedence Mapping.................................................................................................................................238
4.12.3 QoS Basic Mode ...............................................................................................................................................240
4.12.3.1 Global Settings...............................................................................................................................................240
4.12.3.2 Port Settings...................................................................................................................................................241
4.12.4 Bandwidth Control.............................................................................................................................................242
4.12.4.1 Ingress Bandwidth Control.............................................................................................................................242
4.12.4.2 Egress Bandwidth Control..............................................................................................................................243
4.12.4.3 Egress Queue ................................................................................................................................................244
4.12.5 Storm Control....................................................................................................................................................245
4.12.5.1 Global Setting.................................................................................................................................................245
4.12.5.2 Port Setting.....................................................................................................................................................246
4.12.6 Voice VLAN.......................................................................................................................................................248
4.12.6.1 Introduction to Voice VLAN.............................................................................................................................248
4.12.6.2 Properties.......................................................................................................................................................249
4.12.6.3 Telephony OUI MAC Setting...........................................................................................................................250
4.12.6.4 Telephony OUI Port Setting............................................................................................................................252
4.13 Security ..................................................................................................................................................... 253
4.13.1 Access...............................................................................................................................................................253
4.13.1.1 Telnet..............................................................................................................................................................253
4.13.1.2 SSH................................................................................................................................................................255

User’s Manual of IGS-4215 PoE Series
7
4.13.1.3 HTTP..............................................................................................................................................................257
4.13.1.4 HTTPs............................................................................................................................................................258
4.13.2 Access Method Profile Rules.............................................................................................................................259
4.13.2.1 Profile Rules...................................................................................................................................................259
4.13.2.2 Access Profiles...............................................................................................................................................261
4.13.3 AAA...................................................................................................................................................................262
4.13.3.1 Login List........................................................................................................................................................263
4.13.3.2 Enable List......................................................................................................................................................264
4.13.3.3 RADIUS Server..............................................................................................................................................265
4.13.3.4 TACACS+ Server ...........................................................................................................................................268
4.13.4 802.1X...............................................................................................................................................................270
4.13.4.1 Understanding IEEE 802.1X Port-based Authentication.................................................................................270
4.13.4.2 802.1X Setting................................................................................................................................................274
4.13.4.3 802.1X Port Setting........................................................................................................................................275
4.13.4.4 Guest VLAN Setting.......................................................................................................................................277
4.13.4.5 Authenticated Host.........................................................................................................................................279
4.13.5 Port Security......................................................................................................................................................280
4.13.6 DHCP Snooping................................................................................................................................................282
4.13.6.1 DHCP Snooping Overview.............................................................................................................................282
4.13.6.2 Global Setting.................................................................................................................................................284
4.13.6.3 VLAN Setting..................................................................................................................................................285
4.13.6.4 Port Setting.....................................................................................................................................................286
4.13.6.5 Statistics.........................................................................................................................................................288
4.13.6..6 Database Agent.............................................................................................................................................289
4.13.6.7 Rate Limit.......................................................................................................................................................291
4.13.6.8 Option82 Global Setting.................................................................................................................................292
4.13.6.9 Option82 Port Setting.....................................................................................................................................293
4.13.6.10 Option82 Circuit-ID Setting...........................................................................................................................295
4.13.7 Dynamic ARP Inspection...................................................................................................................................296
4.13.7.1 Global Setting.................................................................................................................................................296
4.13.7.2 VLAN Setting..................................................................................................................................................297
4.13.7.3 Port Setting.....................................................................................................................................................298
4.13.7.4 Statistics.........................................................................................................................................................300
4.13.7.5 ARP Rate Limit...............................................................................................................................................301
4.13.8 IP Source Guard................................................................................................................................................302
4.13.8.1 Port Settings...................................................................................................................................................303
4.13.8.2 Binding Table..................................................................................................................................................305
4.13.9 DoS...................................................................................................................................................................306
4.13.9.1 DoS Global Setting.........................................................................................................................................306
4.13.9.2 DoS Port Setting.............................................................................................................................................309
4.13.10 ACL .................................................................................................................................................................310
4.13.10.1 MAC-based ACL...........................................................................................................................................311

User’s Manual of IGS-4215 PoE Series
8
4.13.10.2 MAC-based ACE..........................................................................................................................................312
4.13.10.3 IPv4-based ACL ...........................................................................................................................................315
4.13.10.4 IPv4-based ACE...........................................................................................................................................316
4.13.10.5 IPv6-based ACL ...........................................................................................................................................321
4.13.10.6 IPv6-based ACE...........................................................................................................................................322
4.13.10.7 ACL Binding..................................................................................................................................................327
4.14 Ring ........................................................................................................................................................... 328
4.14.1 Ring Wizard.......................................................................................................................................................329
4.14.2 ERPS ................................................................................................................................................................330
4.15 Power over Ethernet ................................................................................................................................ 333
4.15.1 PoE Switch Introduction ....................................................................................................................................333
4.15.2 Power over Ethernet Powered Device...............................................................................................................334
4.15.3 Power over Ethernet Configuration ...................................................................................................................336
4.15.4 PoE Schedule....................................................................................................................................................343
4.15.5 PoE Alive Check Configuration..........................................................................................................................346
4.16 Maintenance ............................................................................................................................................. 348
4.16.1 Factory Default..................................................................................................................................................348
4.16.2 Reboot Switch...................................................................................................................................................348
4.16.3 Backup Manager...............................................................................................................................................349
4.16.4 Upgrade Manager .............................................................................................................................................350
4.16.5 Dual Image........................................................................................................................................................350
4.17 Diagnostics ............................................................................................................................................... 352
4.17.1 Cable Diagnostics .............................................................................................................................................352
4.17.2 Ping...................................................................................................................................................................354
4.17.2.1 Ping Test.........................................................................................................................................................354
4.17.3 IPv6 Ping Test ...................................................................................................................................................355
5. SWITCH OPERATION ....................................................................................................... 356
5.1 Address Table ............................................................................................................................................. 356
5.2 Learning ...................................................................................................................................................... 356
5.3 Forwarding & Filtering ............................................................................................................................... 356
5.4 Store-and-Forward ..................................................................................................................................... 356
5.5 Auto-Negotiation ........................................................................................................................................ 356
6. TROUBLESHOOTING ....................................................................................................... 357
APPENDIX A Switch's RJ45 Pin Assignments ................................................................... 358
A.1 1000Mbps, 1000BASE-T............................................................................................................................ 358
A.2 10/100Mbps, 10/100BASE-TX ................................................................................................................... 358

User’s Manual of IGS-4215 PoE Series
9
1. INTRODUCTION
Thank you for purchasing PLANET IGS-4215 Industrial Managed Switch series, which comes with multiple Gigabit Ethernet
copper and SFP fiber optic connectibility and robust Layer 2 and Layer 4 features. The description ofthis model is shown below:
IGS-4215-4P4T Industrial 4-Port 10/100/1000T 802.3at PoE + 4-Port 10/100/100T Managed Ethernet Switch
IGS-4215-4P4T2S Industrial 4-Port 10/100/1000T 802.3at PoE + 4-Port 10/100/100T + 2-
Port 100/1000X SFP
Managed Ethernet Switch
IGS-4215-8P2T2S Industrial 8-Port 10/100/1000T 802.3at PoE + 2-Port 10/100/1000T + 2-
Port 100/1000X SFP
Managed EthernetSwitch
IGS-4215-4UP4T2S Industrial 4-Port 10/100/1000T 802.3bt PoE + 4-Port 10/100/100T + 2-
Port 100/1000X SFP
Managed Ethernet Switch
IGS-4215-8UP2T2S Industrial 8-Port 10/100/1000T 802.3bt PoE + 2-Port 10/100/1000T + 2-
Port 100/1000X SFP
Managed Ethernet Switch
“Industrial Managed Switch” is used as an alternative name in this user’s manual.
1.1 Packet Contents
Open the box of the Industrial Managed Switch and carefully unpack it. The box should contain the following items:
Model Name
Item
IGS-4215-
4P4T
IGS-4215-
4P4T2S
IGS-4215-
8P2T2S
IGS-4215-
4UP4T2S
IGS-4215-
8P2T2S
The Industrial Managed Switch ■■■■■
Quick Installation Guide ■■■■■
RS-232 to RJ45 Console Cable ■■■■■
DIN-rail Kit ■■■■■
Wall Mounting Kit ■■■■■
SFP Dust Caps --- 2 2 2 2
RJ45 Dust Caps 9 9 11 9 11
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

User’s Manual of IGS-4215 PoE Series
10
1.2 Product Description
Ideal, Cost-effective, Manageable PoE+ Solution for Hardened Environment
Designed to be installed in heavy industrial demanding environments,PLANET IGS-4215 Industrial-grade, DIN-rail type L2/L4
Managed Gigabit PoE+ Switch series features PLANET intelligent PoE functions to improve the availability of critical business
applications. It provides IPv6/IPv4 dual stack management and built-in L2/L4 Gigabit switching engine along with 4/8
10/100/1000BASE-T ports featuring 30-watt 802.3at PoE+ or 95-watt 802.3bt PoE++, 2/4 additional Gigabit copper ports
and another 2 extra 100/1000BASE-X SFP fiber slots for data and video uplink. The IGS-4215 series is able to operate
reliably, stably and quietly in any environment without affecting its performance. It comes with a total power budget of up to 240
watts for different kinds of PoE applications and operating temperature ranging from -40 to 75 degrees C in a rugged IP30
metal housing.
Model Name
Item
IGS-4215-
4P4T
IGS-4215-
4P4T2S
IGS-4215-
8P2T2S
IGS-4215-
4UP4T2S
IGS-4215-
8UP2T2S
10/100/1000BASE-T
Copper
8 8 10 8 10
100/1000BASE-X SFP - 2 2 2 2
Power over Ethernet
Standard IEEE 802.3at
PoE+ IEEE 802.3at PoE+ IEEE 802.3at PoE+ IEEE 802.3bt PoE++ IEEE 802.3bt PoE++
PoE Ports 4 4 8 4 8
PoE Budget 144 watts 144 watts 240 watts 240 watts 360 watts
Power Inpuit 48~54V DC x 2
Built-in Unique PoE Functions for Powered Devices Management
As it is the managed PoE switch for surveillance, wireless and VoIP networks, the IGS-4215 series features the following
special PoE management functions:
PD alive check
Scheduled power recycling
PoE schedule
PoE usage monitoring
Intelligent Powered Device Alive Check
The IGS-4215 series can be configured to monitor connected PD (powered device) status in real time via ping action. Once the
PD stops working and responding, the IGS-4215 series will resume the PoE port power and bring the PD back to work. It will
greatly enhance the network reliability through the PoE port resetting the PD’s power source and reducing administrator
management burden.

User’s Manual of IGS-4215 PoE Series
11
Scheduled Power Recycling
The IGS-4215 series allows each of the connected PoE IP cameras or PoE wireless access points to reboot at a specific time
each week. Therefore, it will reduce the chance of IP camera orAP crash resulting from buffer overflow.
PoE Schedule for Energy Saving
Under the trend of energy saving worldwide and contributing to environmental protection, the IGS-4215 series can effectively
control the power supply besides its capability of giving high watts power. The “PoE schedule” function helps you to enable or
disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or
enterprises save power and budget. It also increases security by powering off PDs that should not be in use during
non-business hours.

User’s Manual of IGS-4215 PoE Series
12
PoE Usage Monitoring and Intelligent LED Indicator for Real-time PoE Usage
Via the power usage chart in the web management interface, the IGS-4215 series enables the administrator to monitor the
status of the power usage of the connected PDs in real time. Thus, it greatly enhances the management efficiency of the
facilities. Moreover, the IGS-4215 series helps users to monitor the current status of PoE power usage easily and efficiently via
its advanced LED indication. Called “PoE Power Usage”, the front panel of the IGS-4215 series has four LED indicators of
different power usages.
802.3at PoE+ Power and Ethernet Data Transmission Distance Extension
In the “Extend” operation mode, the IGS-4215 PoE series operates on a per-port basis at 10Mbps duplex operation but can
support 20-watt PoE power output over a distance of up to 250 meters overcoming the 100m limit on Ethernet UTP cable. With
this brand-new feature, the IGS-4215-8P2T2S provides an additional solution for 802.3at/bt PoE distance extension, thus
saving the cost of Ethernet cable installation.
802.3bt PoE++ – 90~95-watt Power over 4-pair UTP Solution
As the IGS-4215-8U2TP2S and IGS-4215-4UP4T2S adopt the IEEE 802.bt PoE++ standard, it is capable to source up
to 95 watts of power by using all the four pairs of standard Cat5e/6 Ethernet cabling to deliver power and full-speed data to
each remote PoE compliant powered device (PD). It possesses triple amount of power capability than the conventional 802.3at
PoE+ and is an ideal solution to satisfy the growing demand for higher power consuming network PDs, such as:
PoE PTZ speed dome cameras
Network devices
Thin clients
AIO (all-in-one) touch PCs, point of sale (POS) and information kiosks
Remote digital signage displays
PoE lightings

User’s Manual of IGS-4215 PoE Series
13
Redundant Ring, Fast Recovery for Critical Network Applications
The IGS-4215 series supports redundant ring technology and features strong, rapid self-recovery capability to prevent
interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS (Ethernet Ring Protection
Switching) technology, Spanning Tree Protocol (802.1s MSTP) into customer’s network to enhance system reliability and
uptime in various environments.
Network with Cybersecurity Helps Minimize Security Risks
The IGS-4215 series comes with enhanced cybersecurity to fend off cyberthreats and cyberattacks. It supports SSHv2 and
TLSv1.2 protocols to provide strong protection against advanced threats. Served as a key point to transmit data to customer's
critical equipment in a business network, the cybersecurity feature of the IGS-4215 series protects the switch management and
enhances the security of the mission-critical network without any extra deployment cost and effort.
Environmentally Hardened Design
With the IP30 aluminum industrial case, the IGS-4215 series provides a high level of immunity against electromagnetic
interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets without air
conditioner. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-4215 series can be placed in
almost any difficult environment.

User’s Manual of IGS-4215 PoE Series
14
IPv6/IPv4 Dual Stack Management
Supporting both IPv6 and IPv4 protocols, the IGS-4215 series helps the system integrators to step in the IPv6 era with the
lowest investment as its network facilities need not be replaced or overhauled if the IPv6 network is set up.
Robust Layer 2 Features
The IGS-4215 series can be programmed for advanced switch management functions such as dynamic port link aggregation,
802.1Q VLAN, Q-in-Q VLAN, Multiple Spanning Tree Protocol (MSTP), Loop and BPDU Guard, IGMP Snooping, and MLD
Snooping. Via the link aggregation, the IGS-4215 series allows the operation of a high-speed trunk to combine with multiple
ports such as a 16Gbps fat pipe, and supports fail-over as well. Also, the Link Layer Discovery Protocol (LLDP)is the Layer 2
protocol included to help discover basic information about neighboring devices on the local broadcast domain.
Efficient Traffic Control
The IGS-4215 series are loaded with robust QoS features and powerful traffic management to enhance services to
business-class data, voice, and video solutions. The functionality includes broadcast/multicast/unicast storm control, per port
bandwidth control, 802.1p/CoS/IP DSCP QoS priority and remarking. It guarantees the best performance in VoIP and video
stream transmission, and empowers the enterprises to take full advantage of the limited network resources.
Friendly and Secure Management
For efficient management, the IGS-4215 series is equipped with Command line, Web and SNMP management interfaces.
With the built-in Web-based management interface, the IGS-4215 series offers an easy-to-use,
platform-independent management and configuration facility.
For text-based management, it can be accessed via Telnet and the console port.
By supporting the standard SNMP protocol, the switch can be managed via any SNMP-based management
software.
Moreover, the IGS-4215 series offers secure remote management by supporting SSHv2, TLSv1.2 and SNMP v3 connections
which encrypt the packet content at each session.

User’s Manual of IGS-4215 PoE Series
15
Advanced Network Security
PLANET IGS-4215 series offer a comprehensive IPv4/IPv6 Layer 2 to Layer 4 Access Control List (ACL) for enforcing
security to the edge. Its protection mechanism also comprises 802.1X port-based user and device authentication, which can be
deployed with RADIUS to ensure the port level security and block illegal users. With the protected port function,
communication between edge ports can be prevented to guarantee user privacy. Furthermore, the IGS-4215 series also
provide DHCP snooping, IP source guard and dynamic ARP inspection functions to prevent IP snooping from attack and
discarded ARP packets with invalid MAC address. The network administrators can now construct highly-secure corporate
networks with considerably less time and effort than before.
Flexibility and Long-distance Extension Solution
The IGS-4215 series provides 2 or 4 extra Gigabit TP interfaces supporting 10/100/1000BASE-T RJ45 copper to connect with
surveillance network devices such as NVR, Video Streaming Server or NAS to facilitate surveillance management. Or through
the two dual-speed fiber SFP slots, it can also connect with the 100BASE-FX/1000BASE-SX/LX SFP (Small Form-factor
Pluggable) fiber transceiver to uplink to backbone switch and monitoring center in long distance. The distance can be extended
from 550 meters to 2 kilometers (multi-mode fiber) and to 10/20/40/60/80/120 kilometers (single-mode fiber or WDM fiber).
They are well suited for applications within the enterprise data centers and distributions.
Intelligent SFP Diagnosis Mechanism
The IGS-4215 series supports SFP-DDM (Digital Diagnostic Monitor) function that greatly helps network administrator to
easily monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias
current, and transceiver supply voltage

User’s Manual of IGS-4215 PoE Series
16
1.3 How to Use This Manual
This User Manual is structured as follows:
Section 2, INSTALLATION
The section explains the functions of the Switch and how to physically install the Industrial Managed Switch.
Section 3, SWITCH MANAGEMENT
The section contains the information about the software function of the Industrial Managed Switch.
Section 4, WEB CONFIGURATION
The section explains how to manage the Industrial Managed Switch by Web interface.
Section 5, SWITCH OPERATION
The chapter explains how to do the switch operation of the Industrial Managed Switch.
Section 6, TROUBLESHOOTING
The chapter explains how to troubleshoot the Industrial Managed Switch.
Appendix A
The section contains cable information of the Industrial Managed Switch.

User’s Manual of IGS-4215 PoE Series
17
1.4 Product Features
Physical Port
■Eight 10/100/1000BASE-T Gigabit RJ45 copper ports with 4-/8-port IEEE 802.3at/af PoE Injector
■Two or four 10/100/1000BASE-T Gigabit Ethernet RJ45 ports
■Two 100/1000BASE-X SFP slots, SFP type auto detection
■RJ45 console interface for switch basic management and setup
Power over Ethernet
■Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE
■Backward compatible with IEEE 802.3af Power over Ethernet
■Up to 4/8 ports of IEEE 802.3af/802.3at devices powered
■144-watt PoE budget (IGS-4215-4P4T/IGS-4215-4P4T2S)
■240-watt PoE budget (IGS-4215-8P2T2S)
■Supports PoE power up to 36 watts for each PoE port
■Auto detects powered device (PD)
■Circuit protection prevents power interference between ports
■Remote power feeding up to 100 meters in standard mode and 250m in extend mode
■PoE management
−Total PoE power budget control
−Per port PoE function enable/disable
−PoE port power feeding priority
−Per PoE port power limitation
−PD classification detection
■Intelligent PoE features
−PD alive check
−PoE schedule
Industrial Case and Installation
■IP30 aluminum case
■DIN-rail and wall-mount design
■Supports -40 to 75 degrees C operating temperature
■Supports Ethernet ESD protection of 6KV DC power
■Redundant power design
−48V~54V DC wide power input
Switching
■Hardware based 10/100Mbps (half/full duplex), and 1000Mbps (full duplex) mode, flow control and auto-negotiation
and auto MDI/MDI-X
■Features Store-and-Forward mode with wire-speed filtering and forwarding rates
■IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
■8K MAC address table size
■10K jumbo frame
■Automatic address learning and address aging

User’s Manual of IGS-4215 PoE Series
18
Layer 2 Features
■Supports VLAN
−IEEE 802.1Q tagged VLAN
−Provider bridging (VLAN Q-in-Q, IEEE 802.1ad) support
−Protocol VLAN
−Voice VLAN
−Private VLAN (Protected port)
−Management VLAN
−GVRP
■Supports Spanning Tree Protocol
−STP (Spanning Tree Protocol)
−RSTP (Rapid Spanning Tree Protocol)
−MSTP (Multiple Spanning Tree Protocol)
−STP BPDU Guard, BPDU Filtering and BPDU Forwarding
■Supports Link Aggregation
−IEEE 802.3ad Link Aggregation Control Protocol (LACP)
−Cisco ether-channel (static trunk)
−Maximum 4/8 trunk groups, up to 4 ports per trunk group
■Provides port mirror (many-to-1)
■Loop protection to avoid broadcast loops
Quality of Service
Ingress/Egress Rate Limit per port bandwidth control
■Traffic classification
−IEEE 802.1p CoS
−TOS/DSCP/IP precedence of IPv4/IPv6 packets
Strict priority and Weighted Round Robin (WRR) CoS policies
Multicast
■Supports IPv4 IGMP snooping v2 , v3
■Supports IPv6 MLD snooping v1, v2
■IGMP querier mode support
■IGMP snooping port filtering
■MLD snooping port filtering
Security
■Storm Control support
−Broadcast/unknown unicast/unknown multicast
■Authentication
−IEEE 802.1X port-based network access authentication
−Built-in RADIUS client to co-operate with the RADIUS servers
−DHCP Option 82
−RADIUS/TACACS+ authentication
■Access Control List
−IPv4/IPv6 IP-based ACL
−IPv4/IPv6 IP-based ACE
−MAC-based ACL
−MAC-based ACE

User’s Manual of IGS-4215 PoE Series
19
■MAC Security
−Static MAC
−MAC filtering
■Port security for source MAC address entries filtering
■DHCP snooping to filter distrusted DHCP messages
■Dynamic ARP inspection discardsARP packets with invalid MAC address to IP address binding
■IP source guard prevents IP spoofing attacks
■DoS attack prevention
Management
IPv4 and IPv6 dual stack management
Switch Management Interface
−IPv4/IPv6 Web switch management
−Console and Telnet Command Line Interface
−SNMP v1, v2c, and v3
−SSHv2 and TLSv1.2 secure access
SNMP Management
−Four RMON groups (history, statistics, alarms and events)
−SNMP trap for interface Link Up and Link Down notification
User privilege levels control
Built-in Trivial File Transfer Protocol (TFTP) client
Static and DHCP for IP address assignment
System Maintenance
−Firmware upload/download via HTTP/TFTP
−Configuration upload/download through HTTP/TFTP
−Hardware reset button for system reboot or reset to factory default
−Dual images
SNTP Network Time Protocol
Network Diagnostic
−Cable diagnostics
−ICMPv6/ICMPv4 Remote Ping
−SFP-DDM (Digital Diagnostic Monitor)
Link Layer Discovery Protocol (LLDP) Protocol and LLDP-MED
Event message logging to remote syslog server
PLANET Smart Discovery Utility for deployment management
PLANET NMS system and CloudViewer for deployment management

User’s Manual of IGS-4215 PoE Series
20
1.5 Product Specifications
Product
IGS-4215-
4P4T
IGS-4215-
4P4T2S
IGS-4215-
8P2T2S
IGS-4215-
4UP4T2S
IGS-4215-
8UP2T2S
Hardware Specifications
Hardare Version
V2 v2 v2 v1 v1
Copper Ports 8 8 10 8 10
10/100/1000BASE-T RJ45 auto-MDI/MDI-X port
PoE Injector Port 4 4 8 4 8
802.3at PoE+ 802.3at PoE+ 802.3at PoE+ 802.3bt PoE++ 802.3bt PoE++
SFP Ports
- 2 2 2 2
- 1000BASE-SX/LX/BX SFP interfaces
Compatible with 100BASE-FX SFP
Console 1 x RS232-to-RJ45 serial port (115200,8, N, 1)
Reset Button < 5 sec: System reboot
> 5 sec: Factory default
Connector Removable 6-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin 5/6 for Power 2
Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24V AC
Power Requirements
48~54V DC,
6A (max.) 48~54V DC, 6A (max.) 48~54V DC, 6A (max.) 48~54V DC, 6A (max.) 48~54V DC, 8.5A (max.)
(>52V DC for PoE+ output recommended)
Power
Consumption/
Dissipation
System On Max.4.32 watts/
14.73BTU Max. 6.72 watts/
22.91BTU Max. 6.72 watts/
22.91BTU
Max. 8.2 watts/
27.96BTU
Max. 9.18 watts/
31.3BTU
PoE Full
Loading
Max. 151 watts/
514.91BTU Max. 156 watts/
531.96BTU
Max. 252 watts/
859.32BTU
Max. 264 watts/
900.24BTU
Max. 390 watts/
1329.9BTU
Dimensions (W x D x H) 76.8 x 107.3 x 152 mm
Weight
1,000g 1,043g 1,084g 1054g 1091g
Enclosure IP30 aluminum case
Installation DIN-rail kit and wall-mount ear
ESD Protection Contact Discharge 6KV DC
Air Discharge 8KV DC
Switching Specifications
Switch Architecture Store-and-Forward
Switch Fabric 16Gbps/
non-blocking
20Gbps
/non-blocking
24Gbps
/non-blocking
20Gbps
/non-blocking
24Gbps
/non-blocking
Switch Throughput@64 bytes 11.9Mpps 14.8Mpps 17.85Mpps 14.8Mpps 17.85Mpps
MAC Address Table
8K entries
Shared Data Buffer 4.1 megabits
Flow Control IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 10 Kbytes