Planet FNSW-2402S User manual

Trademarks
Copyright  PLANET Technology Corp. 2003
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information
in this User’s Manual, and reserves the right to make improvements to this
User’s Manual and/or to the products described in this User’s Manual, at any
time without notice.
If you nd information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Revision
PLANET 24-port + 2-slot Smart Fast Ethernet Switch User’s Manual
FOR MODEL: FNSW-2402S
Part No.: 2010-000023-000

1
Table of Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 How to Use This Manual 1
1.3 Product Features 1
1.4 Product Specifications 2
Chapter 2 Installation 5
2.1 Product Description 5
2.2 Installing a FNSW-2402S 6
Chapter 3 Configuration 9
3.1 Preparing for configuration 9
3.2 Getting Started 11
Chapter 4 Switch Operation 31
4.1 Address Table 31
4.2 Learning 31
4.3 Forwarding & Filtering 31
4.4 Store-and-Forward 31
4.5 Auto-Negotiation 32
Chapter 5 Troubleshooting 33
Appendix A Troubleshooting 35
A.1 Switch‘s RJ-45 Pin Assignments 35

1
Chapter 1
INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
● Smart Fast Ethernet Switch x1
● User’s manual x1
● Power cord x1
● Two Rack-Mounting Brackets with Attachment Screws x1
● RS-232 cable x1
If any of these are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against
to repack the product in case there is a need return to it to us for repairing.
1.2 How to Use This Manual
This Smart Fast Ethernet Switch User’s Manual is structured as follows:
• Section 2, Installation
It explains the functions of FNSW-2402S and how to physically install the
FNSW-2402S.
• Section 3, Configuration
It contains information about the smart function of FNSW-2402S.
• Section 4 Switch operation
It explains the Switch operation of FNSW-2402S.
• Section 5 Troubleshooting
It contains troubleshooting guide of FNSW-2402S.
• Appendix A
It contains cable information of FNSW-2402S.
1.3 Product Features
• Complies with IEEE802.3 and 802.3u standards for 100Base-TX/FX
• 24-port 10/100 Mbps Fast Ethernet Switch
• Each Switching ports support auto-negotiation-10/20, 100/200Mbps sup-

2
3
ported
• 2 open slots for 10/100Base-TX/FX fiber-optic interface with various connec-
tion media and distances
• Auto-MDI/MDI-X detection on each RJ-45 port
• Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame
flow control (full-duplex)
• High performance Store and Forward architecture, broadcast storm control,
runt/CRC filtering eliminates erroneous packets to optimize the network band-
width
• 6K MAC address table, automatic source address learning and ageing
• 512K bytes shared data memory buffering
• Console interface for Switch basic management and setup
• Support port-based VLAN and IEEE 802.1Q VLAN function.
• Support up to 7 Trunk groups, each trunk for up to maximum 4 port with
800Mbps bandwidth
• Support rate control on each port
1.4 Product Specications
Model FNSW-2402S
Hardware Specification
Network ports 24 10/100Base-T RJ-45 MDI/MDI-X ports
Module slot 2 open slot for 10/100Base-TX/FX fiber-optic interface
Console port 1 RS-232 DB-9 male
Dimensions 440 x 200 x 44 mm (1U height)
Weight 2.6 kg
Power Requirement 100~240 (±10%) VAC, 50-60 (±3) Hz
Power Consumption 30 Watts maximum / 100 BTU/hr maximum
Switch Specification
Switch architecture Store-and-forward
Address Table 6K entries, auto learning/ageing
Shared data Buffer 512K bytes

2
3
Flow Control Back pressure for half duplex, IEEE 802.3x for full du-
plex
Packet Control Runt & CRC filtering, Broadcast storm control
Switching Fabric 8.8Gbps
Switch Management
Port Configuration Port disable/enable. Rate control configuration Auto-
negotiation/NWAY _FORCE/ FORCE mode selection.
10/100Mbps full and half duplex mode selection. Flow
control disable/enable.
Port Status Display each port’s link status, disable/enable status, and
speed duplex mode. Flow control status
Aging control Disable/Enable
VLAN Port-based VLAN and IEEE 802.1Q VLAN
Port Trunking 7 groups of 4-port trunk support
Standards Conformance
Network Standards IEEE 802.3 (Ethernet), IEEE 802.3u (Fast Ethernet),
IEEE802.3x (flow control), IEEE 802.1Q VLAN
Operating Tempera-
ture
0~50˚C
Storage Tempera-
ture
-40~70˚C
Humidity 5% to 95% (Non-condensing)
Regulation Compli-
ance
FCC Class A, VCCI Class A, CISPR 22 Class A

4
5

4
5
Chapter 2
INSTALLATION
This section describes the functionalities of FNSW-2402S components and guides how to
install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read
this chapter completely before continuing.
2.1 Product Description
The PLANET FNSW-2402S provides 24 10/100Mbps Fast Ethernet Switch ports with 2
open slots for available for 10/100Base-TX/ 100Base-FX Fast Ethernet modules. The
optional modules can be 10/100Base-TX TP port or multi-mode ber using either SC or
ST connectors. The PLANET FNSW-2402S with non -blocking backplane and simplies the
task of upgrading your LAN to cater for increased bandwidth demand. Equipped with a
console interface, the FNSW-2402S Smart Switch can be programmed for basic switch
management functions such as port speed conguration, rate control, VLAN and Port
Trunking.
2.1.1 Product Overview
PLANET FNSW-2402S is a Smart Fast Ethernet switch with 24 RJ-45 10/100Mbps ports
and up to two 100Mbps ber ports or two 10/100Mbps TP ports for cost effective high-
performance network connectivity. With its 8.8Gbps non-blocking switch fabric, the
PLANET FNSW-2402S can also provide a local, high bandwidth, Fast Ethernet network
for your departmental backbone plus the ability to trunk two ports (200Mbps) to enable
switch-to-switch backbone. The advanced functionality of the FNSW-2402S eliminates
traditional problems associated with the use of Ethernet. Users can be segregated using
built-in VLAN functionality. This, coupled with the exible ber module options, make
the FNSW-2402S one of the best and most cost-effective MTU switch solutions for Multi-
tenant service providers.
This product also supports store-and-forward forwarding scheme to ensure low latency
and high data integrity, eliminates unnecessary trafc and relieves congestion on critical
network paths. With an intelligent address recognition algorithm, FNSW-2402S could
recognize up to 6K different MAC address and enables ltering and forwarding at full
wire speed.
2.1.2 FNSW-2402S Front Panel
Figure 2-1 shows front panel of FNSW-2402S.
Figure 2-1 PLANET FNSW-2402S Front Panel

6
7
2.1.3 LED Indicators
LED Color Function
PWR Green Lit: Power on
LNK/ACT Green Lit: indicate the link through that port is successfully
established
Blink: indicate that the switch is actively sending or
receiving data over that port
100 Orange Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is operating at 10Mbps.
2.1.4 Extension Slots
The Switch extension slots #25 and #26 can be a 10/100Base-TX/FX switching port as
the extension module installed.
Please refer to the section 3.2.3.1 Port Conguration for the detailed installation and
settings.
2.1.5 FNSW-2402S Rear Panel
The rear panel of the Switch indicates an AC inlet power socket, which accepts input
power from 100 to 240VAC, 50-60Hz. Figure 2-2 shows Rear panel of FNSW-2402S.
Figure 2-2 Rear Panel of FNSW-2402S
Power Notice:
1.The device is a power-required device, it means, it will not work till it is
powered. If your networks should active all the time, please consider using
UPS (Uninterrupted Power Supply) for your device. It will prevent you from
network data loss or network downtime.
2.In some area, installing a surge suppression device may also help to protect
your switch from being damaged by unregulated surge or current to the
Switch or the power adapter.
2.2 Installing a FNSW-2402S
This part describes how to install your FNSW-2402S Smart Fast Ethernet Switch and make
connections to the switch. Please read the following topics and perform the procedures in
the order being presented.
To install your FNSW-2402S on a desktop or shelf, simply complete the following steps.

6
7
2.2.1 Desktop Installation
To install a FNSW-2402S on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the switch.
Step2: Place the FNSW-2402S on a desktop or shelf near an AC power source.
Step3: Keep enough ventilation space between the switch and the surrounding
objects.
Note: When choosing a location, please keep in mind the environmental re-
strictions discussed in Chapter 1, Section 4, Specification.
Step4: Connect your FNSW-2402S to network devices
A.Connect one end of a standard network cable to the 10/100 RJ-45 ports on
the front of the FNSW-2402S.
B.Connect the other end of the cable to the network devices such as printer
servers, workstations or routers…etc.
Note: Connection to the Switch requires UTP Category 5 network cabling with
RJ-45 tips. For more information, please see the Cabling Specification
in Appendix A.
Step5: Supply power to the Switch.
A.Connect one end of the power cable to the FNSW-2402S
B.Connect the power plug of the power cable to a standard wall outlet then
power on the FNSW-2402S.
When the FNSW-2402S receives power, the Power LED should remain solid Green.
2.2.2 Rack Mounting
To install the switch in a 19-inch standard rack, follow the instructions described below.
Step1: Place your FNSW-2402S on a hard flat surface, with the front panel posi-
tioned towards your front side.
Step2: Attach a rack-mount bracket to each side of the switch with supplied
screws attached to the package. Figure 2-3 shows how to attach brackets
to one side of the switch.

8
9
Figure 2-3 Attaching the brackets to the FNSW-2402S
Caution:
You must use the screws supplied with the mounting brackets. Damage
caused to the parts by using incorrect screws would invalidate your war-
ranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the switch, use suitable screws to se
curely attach the brackets to the rack, as shown in Figure 2-4
Figure 2-4 Mounting the Switch in a Rack
Step 6: Proceed with the steps 4 and steps 5 of section 2.2.1 Desktop Installation
to connect the network cabling and supply power to your switch.