Planet LRP-422CST User manual

Industrial 4-port Coax + 2-port 10/100/1000T
+ 2-port 100/1000X SFP
Long Reach PoE over Coaxial Managed Switch
LRP-422CST
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
4. Terminal Setup ........................................................................................... 6
5. Logon to the Console .................................................................................. 7
6. ConguringIPAddressviatheConsole ........................................................ 8
7. SavingtheCongurationviatheConsole.....................................................10
8. Starting Web Management .........................................................................11
9. Starting Long Reach PoE Communication .....................................................14
10.SavingCongurationviatheWeb...............................................................18
11.RecoveringBacktoDefaultConguration ....................................................19
12. Customer Support.....................................................................................20

3
1. Package Contents
Thankyou for purchasingPLANET Industrial4-port Coax+2-port 10/100/1000T+
2-port100/1000XSFPLongReachPoEoverCoaxialManagedSwitch.
“LRP Managed Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the LRP Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheLRPManagedSwitchx1
zQuickInstallationGuidex1
zRS232toRJ45ConsoleCablex1
zSFPDustCapx2
zBNCFemaleDustCapx4
zWarningStickerx4
zDIN-railKitx1
zWallMountingKitx1
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
SerialPortConnection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheLRPManagedSwitch.
Ethernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
theLRP Managed Switch.Ifthe Web interface of theLRP Managed
Switch is not accessible, please turn off the anti-virus software or
firewallandthentryitagain.

5
3. Wiring the Power Inputs
The Upper Panel of the LRP Managed Switch indicates a DC inlet power socket
and consists of one terminal block connector within 6 contacts. Please follow the
steps below to insert the power wire.
1.Insert positive/negative DC power wires into contacts 1 and 2 for Power 1 or 5,
and6forPower2.
LRP-422CST: DC 48~56V
Input DC 48-56V
DC1 DC2
Fault
Figure 3-1: LRP-422CST Upper Panel
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
1 2 3 4 5 6
V1+ V1- V2+ V2-
Power 1 Power 2
Positive (+) Pin Negative (-) Pin
LRP-422CST Pin 1/5 Pin 2/6
Note
The wire gauge for the terminal block should be in the range from
12to24AWG.

6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to the RJ45 type of the console port of the LRP Managed
Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: LRP Managed Switch Console Connectivity
A terminal program is required to make the software connection to the LRP
ManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud :115200
zDatabits :8
zParity :None
zStopbits :1
zFlowcontrol :None
Figure 4-2:COMPortConguration

7
5. Logon to the Console
Once the terminal is connected to the device, power on the LRP Managed Switch,
and the terminal will display “running testing procedures”. Then, the following
message asks to log-in user name and password. The factory default user name
andpasswordareshownasfollows,andtheloginscreeninFigure5-1appears.
Username:admin
Password:admin
Figure 5-1: LRP Managed Switch Console Login Screen
The user can now enter commands to manage the LRP Managed Switch. For a
detaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
passwordafterthisfirstsetup.
2.Only accept command in lowercase letter under console
interface.

8
6.ConguringIPAddressviatheConsole
TheLRPManagedSwitchisshippedwithdefaultIPaddressasfollows:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP address
1.Atthe“LRP-series#”prompt,enter“show ip”.
2.Thescreendisplays thecurrentIP address,SubnetMask and Gatewayasshown
inFigure6-1.
Figure 6-1: IP Information Screen

9
 ConguringIPaddress
3.Atthe“LRP-series#”prompt,enter“congure”.
4.Atthe“LRP-series (cong)#”prompt,enterthefollowingcommandandpress
<Enter>asshowninFigure6-2.
LRP-series(cong)# ip address 192.168.1.100 mask 255.255.255.0
LRP-series(cong)# ip default-gateway 192.168.1.254
ThepreviouscommandwouldapplythefollowingsettingsfortheSwitch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Figure 6-2: IP Address Screen
5.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the LRP Managed Switch will apply the new IP
addresssettingimmediately.YoucanaccesstheWebinterfaceoftheLRP Managed
SwitchthroughthenewIPaddress.
Note
If you are not familiar with console command or the related
parameter, enter “?” anytime in console to get the help
description.

10
7.SavingtheCongurationviatheConsole
In the switch, the running conguration le stores in the RAM. In the current
version, the running conguration sequence running-cong can be saved from the
RAMto FLASHby copying the running-cong startup-cong command,so that
the running conguration sequence becomes the startup conguration le, which is
calledcongurationsave.
1.At the “LRP-series#” prompt, enter “copy running-cong startup-cong”
asshowninFigure7-1.
Figure 7-1: The Conguration Screen