Planet WGSW-48040HP User manual

48-Port 10/100/1000Mbps 802.3at PoE
Managed Switch with 4 Shared SFP Ports
WGSW-48040HP
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
4. Logon to the Console .................................................................................. 6
5. ConguringIPAddress................................................................................ 7
6. Starting Web Management .........................................................................10
7. SavingConguration..................................................................................13
8. RecoveringBacktoDefaultConguration.....................................................14
9. Customer Support .....................................................................................15

3
1. Package Contents
ThankyouforpurchasingPLANET48-Port10/100/1000Mbps802.3atPoEManaged
Switch with 4 shared SFP ports, WGSW-48040HP. “Managed Switch” mentioned
inthisGuidereferstotheWGSW-48040HP.
Open the box of the Managed Switch and carefully unpack it. The box should
contain the following items:
TheWGSW-48040HPManagedSwitchx1l
User’s Manual CD x 1l
QuickInstallationGuidex1l
RJ-45toRS232Cablex1l
RubberFeetx4l
TwoRack-mountingBracketswithAttachmentScrewsx1l
PowerCordx1l
SFPDustCapx4l
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,l
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)l
Serial Port Connectionl(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS-232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
Ethernet Port Connectionl
Networkcables--Usestandardnetwork(UTP)cableswithRJ-45connectors.
The above PC is installed with Web Browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.

5
3. Terminal Setup
Tocongurethesystem,connectaserialcabletoaCOM port on a PC or notebook
computerandtoRJ-45typeofserial(console)portoftheManagedSwitch.
PC / Workstation with
Terminal Emulation Software
RJ-45 Type Serial Port
115200,N,8,1
RJ-45 DB9 RS-232 Cable
Managed Switch
Serial Port
Console
115200,N,8,1
Figure 3-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch. Windows’ Hyper Terminal program may be a good choice. The Hyper
TerminalcanbeaccessedfromtheStart menu.
1. Click START,thenPrograms,AccessoriesandthenHyper Terminal.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud :115200
Data bits : 8
Parity :None
Stop bits : 1
Flowcontrol :None
Figure 3-2 Hyper Terminal COM Port Conguration

6
4. Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollowsandtheloginscreeninFigure4-1appears.
Username: admin
Password:admin
Figure 4-1: Managed Switch Console Login Screen
Theuser cannow entercommandstomanage the ManagedSwitch.Foradetailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1. For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

7
5.ConguringIPAddress
TheManagedSwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
Tocheckthe currentIPaddressormodify a newIPaddressforthe Switch,please
usetheproceduresasfollows:
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure5-1.
Figure 5-1: IP Information Screen

8
 ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure5-2.
# congure terminal
(cong)# interface vlan 1
(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPAddress:192.168.1.100
Subnet Mask: 255.255.255.0
Figure 5-2: Conguring IP Address Screen
4.Repeatstep1tocheckiftheIPaddressischanged.

9
 Storecurrentswitchconguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 5-3: Saving Current Conguration Command Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
SwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

10
6. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set on the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
thenthemanagerPCshouldbesetat192.168.0.x(wherexisanumberbetween
1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation with
IE Browser
192.168.0.x
RJ-45/UTP-Cable
IP Address
192.168.0.100
Managed Switch
Figure 6-1: IP Management Diagram
Logging in the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhave
justchangedinconsole)toaccesstheWebinterface.