Planet ISW-504PS User manual

User's Manual
ISW-504PS / ISW-514PS
ISW-514PS15 / ISW-514PSF
5-Port 10/100Mbps with
4-Port PoE Web Smart
Industrial Ethernet Switch
-1-

User’s Manual
Trademarks
Copyright ©PLANET Technology Corp. 2010.
Contents subject to revise without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from the power circuit.
Without removing power cable, the device will still consuming power from the power source. In the view of Saving the
Energy and reduce the unnecessary power consuming, it is strongly suggested to remove the power connection for the
device if this device is not intended to be active.
-2 -

User’s Manual
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 5-Port 10/100Mbps with 4-Port PoE Web Smart Industrial Ethernet Switch User's Manual
FOR MODELS: ISW-504PS / ISW-514PS / ISW-514PS15 / ISW-514PSF
REVISION: 1.0 (JULY.2010)
Part No.: EM-ISW-5xxPS Series_v1.0 (2080-AH0240-000)
-3 -

User’s Manual
TABLE OF CONTENTS
1. INTRODUCTION ............................................................................................................7
1.1 PACKAGE CONTENTS.................................................................................................................................7
1.2 PRODUCT DESCRIPTION .............................................................................................................................7
1.3 FEATURES.................................................................................................................................................8
1.4 SPECIFICATION ..........................................................................................................................................9
1.5 PRODUCT APPLICATION ...........................................................................................................................11
2. INSTALLATION............................................................................................................12
2.1 HARDWARE DESCRIPTION ........................................................................................................................12
2.1.1 Physical Dimension......................................................................................................................... 12
2.1.2 Front Panel ..................................................................................................................................... 12
2.1.2 Front Panel ..................................................................................................................................... 13
2.1.3 LED Indicators ................................................................................................................................14
2.1.4 Switch Upper Panel ........................................................................................................................ 15
2.2 INSTALL THE SWITCH................................................................................................................................16
2.2.1 Installation Steps............................................................................................................................. 16
2.2.2 DIN-Rail Mounting........................................................................................................................... 16
2.2.3 Wall Mount Plate Mounting............................................................................................................. 19
2.3 WIRING THE POWER INPUTS .....................................................................................................................19
2.4 WIRING THE FAULT ALARM CONTACT .......................................................................................................20
2.5 CABLING .................................................................................................................................................21
2.5.1 Installing the SFP transceiver (ISW-514PSF Only) ........................................................................ 21
2.5.2 Remove the module........................................................................................................................ 23
3 MANAGEMENT.............................................................................................................24
3.1 OVERVIEW...............................................................................................................................................24
3.2 REQUIREMENTS .......................................................................................................................................24
3.3 MANAGEMENT METHOD ...........................................................................................................................24
3.3.1 Web Management........................................................................................................................... 24
3.3.2 PLANET Smart Discovery Utility..................................................................................................... 27
4. WEB CONFIGURATION ..............................................................................................29
4.1 MAIN MENU .............................................................................................................................................29
4.2 WEB PANEL.............................................................................................................................................30
4.3 SYSTEM...................................................................................................................................................31
-4 -

User’s Manual
4.3.1 System Information ......................................................................................................................... 32
4.3.2 IP Configuration .............................................................................................................................. 33
4.3.3 Password Setting ............................................................................................................................ 34
4.3.4 Firmware Upgrade .......................................................................................................................... 34
4.3.5 Configuration Setting ...................................................................................................................... 38
4.3.6 Configuration Backup...................................................................................................................... 40
4.3.7 Managed IP..................................................................................................................................... 41
4.3.8 Fault Relay Alarm ........................................................................................................................... 41
4.3.9 Alert Trap Configuration.................................................................................................................. 42
4.3.10 System Reboot ............................................................................................................................. 43
4.4 PORT MANAGEMENT ................................................................................................................................44
4.4.1 Port Configuration ........................................................................................................................... 44
4.4.2 Port Status ...................................................................................................................................... 45
4.4.3 Port Security ................................................................................................................................... 46
4.5 VLAN .....................................................................................................................................................47
4.5.1 VLAN Group.................................................................................................................................... 50
4.5.2 VLAN Per Port Setting .................................................................................................................... 54
4.5.3 VLAN setting example: ................................................................................................................... 56
4.6 QUALITY OF SERVICE...............................................................................................................................63
4.6.1 802.1p Tag Priority Mode................................................................................................................ 64
4.6.2 DSCP QoS Mode............................................................................................................................ 66
4.6.3 Port-Based Priority Mode................................................................................................................ 69
4.7 STORM CONTROL.....................................................................................................................................70
4.8 MISC CONFIGURATION .............................................................................................................................71
4.9 POECONFIGURATION ..............................................................................................................................73
4.9.1 Power over Ethernet Powered Device............................................................................................ 73
4.9.2 Power Management:....................................................................................................................... 73
4.10 LOGOUT ................................................................................................................................................76
5. SWITCH OPERATION..................................................................................................77
5.1 ADDRESS TABLE......................................................................................................................................77
5.2 LEARNING................................................................................................................................................77
5.3 FORWARDING &FILTERING ......................................................................................................................77
5.4 STORE-AND-FORWARD ............................................................................................................................77
5.5 AUTO-NEGOTIATION.................................................................................................................................78
-5 -

User’s Manual
6. POWER OVER ETHERNET OVERVIEW.....................................................................79
7. THE POE PROVISION PROCESS...............................................................................82
7.1 LINE DETECTION......................................................................................................................................82
7.2 CLASSIFICATION ......................................................................................................................................82
7.3 START-UP................................................................................................................................................83
7.4 OPERATION .............................................................................................................................................83
7.5 POWER DISCONNECTION SCENARIOS........................................................................................................83
8. TROUBLESHOOTING..................................................................................................85
APPENDIX A NETWORKING CONNECTION .................................................................86
A.1 DATA OUT POESWITCH RJ-45 PORT PIN ASSIGNMENTS (PORT 1TO PORT-4).......................................86
A.2 10/100MBPS,10/100BASE-TX ...............................................................................................................86
APPENDIX B....................................................................................................................88
B.1 POWER OVER ETHERNET COMPATIBILITY TEST .........................................................................................88
B.2 COMPATIBLE 100BASE-FX SFP TRANSCEIVER LIST (ISW-514PSF)........................................................88
-6 -

User’s Manual
1. INTRODUCTION
The PLANET Layer 2 Web Smart Industrial PoE Switch series – ISW-5xxPS is multiple 10/100Mbps ports Ethernet
Switched with 4-Port 802.3af PoE inject ability and robust layer 2 features; the description of these models as below:
ISW-504PS : 5-Port 10/100Mbps with 4-PoE Industrial Web Smart Switch (-10~60 Degree C)
ISW-514PS : 4+1 100FX Port (SC) with 4-PoE Industrial Web Smart Switch - 2km (-10~60 Degree C)
ISW-514PS15 : 4+1 100FX Port (SC) with 4-PoE Industrial Web Smart Switch - 15km (-10~60 Degree C)
ISW-514PSF : 4+1 100FX Port (LC) with 4-PoE Industrial Web Smart Switch (-10~60 Degree C)
1.1 Package Contents
Check the contents of your package for following parts:
Managed PoE Switch x1
User's Manual CD x1
Quick Installation Guide x1
DIN Rail Kit x 1
Wall Mount Kit x 1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it to us
for repair.
1.2 Product Description
The ISW-504PS / ISW-514PS series support MDI/ MDI-X convertible on 5 / 4-10/100Mbps ports, also provide PoE inject
function on port 1, 2, 3 and 4, which is able to drive 4 IEEE 802.3af compliant powered devices. The dual speed ports use
standard twisted-pair cabling and are ideal for SOHO or segmenting networks into small. Each 10/100Mbps port can
supports up to 200Mbps of throughput in full-duplex mode, ISW-504PS / ISW-514PS series also provides a simple,
cost-effective, and highly reliable network connection for data transmits. Furthermore, it is the ideal device for bridging
among Ethernet, Fast Ethernet workgroups and networks.
With 4 PoE interfaces, the ISW-504PS / ISW-514PS series is ideal for small business and workgroups requiring to deploy
the PoE for the wireless access points, IP-based surveillance camera or IP phones in any places easily, efficiently and cost
effective.
The front panel of ISW-504PS / ISW-514PS series provides LEDs for easy recognition of the switch operation status and
troubleshooting. These LED indicators display the power status for the system, LNK/ACT and speed for each10/100M
port. Also the PoE in use LED indicates for PoE ports (port 1 to port 4).
With data and power over Ethernet from one unit, the ISW-504PS / ISW-514PS series shall reduce cables and eliminates
the need for dedicated electrical outlets on the wall, ceiling or any unreachable place. A wire carries both data and power
lowering the installation costs, simplifying the installation effort and eliminating the need for electricians or extension cords.
-7 -

User’s Manual
The smart functions make it easy to survey and control the PoE power provision to the devices by the Web interface. Basic
switching functions such as VLAN, bandwidth control and QoS are available for network management.
With Fast Ethernet SFP interface, the ISW-514PSF is with high reliability and flexibility to extend the distance from 2km to
20Km. It depends on the MFB family Fast Ethernet SFP modules.
1.3 Features
¾Interfaces
Ports Fiber Optical Interface
Model Name Copper Optical Mode Connector Distance
ISW-504PS 5 x 10/100Base-TX NA NA NA NA
ISW-514PS Multi-Mode SC 2km
ISW-514PS15 Single-Mode SC 15km
ISW-514PSF
4 x 10/100Base-TX 1 x 100Base-FX
Optional SFP
Module LC
Depend on
SFP
Module
4-Port support 48V DC power to PoE Powered Device
¾PoE
Comply with IEEE 802.3af Power over Ethernet End-Span PSE
Up to 4 IEEE 802.3af devices powered
Support PoE Power up to 15.4 Watts for each PoE ports
Auto detect powered device (PD)
Circuit protection prevent power interference between ports
Remote power feeding up to 100m
¾PoE Management
Total PoE power budget control
Enable / Disable PoE function on each port
PoE port Power feeding priority
Power limit on PoE port
PD classification detection
¾Web Management
Web interface for remote management
Firmware upgrade through Web interface
SNMP Trap for alarm notification of events
VLAN and QoS configuration
PLANET Smart Discovery utility automatically finds PLANTE devices on the network
¾Switching
Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX / 100Base-FX Ethernet standard
Supports Auto-Negotiation and 10/100Mbps Half / Full Duplex and Auto MDI / MDI-X
-8 -

User’s Manual
High performance Store and Forward architecture, Storm Control and runt/CRC filtering eliminates erroneous
packets to optimize the network bandwidth
Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE Frame flow control
(Full-Duplex)
Backplane (Switching Fabric): 1Gbps
Automatic address learning and address aging
Integrated address look-up engine, support 1K absolute MAC addresses
CSMA/CD Protocol
¾Industrial Case / Installation
IP-30 Aluminum case / Protection
DIN Rail and Wall Mount Design
24 or 48V DC, redundant power with polarity reverse protect function
Supports EFT protection 6000V DC for power line
Supports 6000V DC Ethernet ESD protection
-10 to 60 Degree C operation temperature
1.4 Specification
Model ISW-504PS ISW-514PS ISW-514PS15 ISW-514PSF
Hardware Specification
10/100Base-TX Ports 5 4 4 4
100Base-FX Interface N/A
1
(SC-Multi Mode,
2km)
1
(SC-Single Mode,
15km)
1
(LC-Opitional SFP
module )
IEEE 802.3af PoE Ports 4 4 4 4
Dimensions (D x W x H) 135mm x 87.8mm x 56mm
Weight 871g
Power Requirement 24 or 48V DC
Installation DIN Rail Kit and Wall Mount Ear
Power Over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output 48V DC Per Port, 350mA . Max. 15.4 Watts
Power Pin Assignment 1/2(+), 3/6(-)
Switch Specification
Switch Processing Scheme Store-and-Forward
Address Table 1K entries
Flow Control Back Pressure for Half Duplex
IEEE 802.3x Pause Frame for Full Duplex
Switch Fabric 1Gbps
Throughput
(Packet Per Second) 0.74Mpps
-9 -

User’s Manual
10/100Base-TX:
Cat. 3, 4, 5, 5e, 6 UTP cable (100meters max.)
EIA/TIA-568 100-ohm STP (100meters max.)
Network Cables
NA
Multi-mode optic fiber
62.5/125μm,
50/125μm (2km max.).
Single-mode optic
fiber 9/125μm (15km
max.).
Multi-mode optic
fiber 62.5/125μm,
50/125μm
Single-mode optic
fiber 9/125μm
(Vary on SFP
Module)
Layer 2 Function
Management Web management, SNMP Trap
VLAN
•Port-Based VLAN
•IEEE 802.1Q Tag-Based VLAN
Up to 16 VLAN groups
QoS
2 priority queues for three type of Class of Service
•Port-Based
•IEEE 802.1p priority tag
•TCP/IP header’s DSCP classifier
Weighted Round Robin queue scheduling
Bandwidth Control Inbound Rate Limit and Outbound Traffic shaping
Storm Control Disable, 12.5%, 25%, 50%, 62.5% 4 levels
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3af Power over Ethernet
IEEE 802.1Q VLAN
IEEE 802.1p Class of Service
Temperature Operating: -10 to 60℃
Storage: -40 to 70℃
Humidity Operating: 5~90%, Storage: 5~90% (Non-condensing)
Regulation Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32(Free Fall)
IEC60068-2-27(Shock)
IEC60068-2-6(Vibration)
-10 -

User’s Manual
1.5 Product Application
As a department / workgroup PoE Switch
Providing up to 4 PoE, in-line power interface, the Industrial PoE Switch can easily build a power central-controlled IP
phone system, IP Camera system, AP group for the enterprise. For instance, 4 camera / AP can be easily installed around
the corner in the company for surveillance demands or build a wireless roaming environment in the office. Without the
power-socket limitation, the Industrial PoE Switch makes the installation of cameras or WLAN AP more easily and
efficiently.
Figure 1-1 PoE Switch connection
Cable distance for Switch
1. The UTP/STP cable distances between PCs should not exceed 100 meters.
2. The Fiber Optic cable distances between PCs should not exceed maximum distance support
by each model.
-11 -

User’s Manual
2. INSTALLATION
2.1 Hardware Description
The ISW-504PS / ISW-514PS series provide two different running speeds – 10Mbps, 100Mbps in the same Switch and
automatically distinguish the speed of incoming connection.
This section describes the hardware features of ISW-504PS / ISW-514PS series. For easier management and control of
the Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit
LED indicators. Before connecting any network device to the ISW-504PS / ISW-514PS series, read this chapter carefully.
In the following section, the term “Industrial PoE Switch” means the ISW-504PS / ISW-514PS / ISW-514PS15 /
ISW-514PSF.
2.1.1 Physical Dimension
ISW-5xxPS series Web Smart Industrial Switch dimension (D x W x H) : 135mm x 87.8mm x 56mm
-12 -

User’s Manual
2.1.2 Front Panel
Figure 2-1 shows a front panel of Industrial PoE Switch.
Figure 2-1 ISW-504PS and ISW-514PS / ISW-514PS15 and ISW-514PF Switch front panel
■ Reset Button
At the left of front panel, the reset button is designed for reboot the Industrial PoE Switch without turn off and on the
power, also can reset the Industrial PoE Switch to factory default mode.
-13 -

User’s Manual
Figure 2-2 Reset button of Industrial PoE Switch
1. Press the RESET button once. The Industrial PoE Switch will reboot automatically.
2. Press the RESET button for 5 seconds. The Industrial PoE Switch will back to the factory
default mode; the entire configuration will be erased.
2.1.3 LED Indicators
System
LED Color Function
P1 Green Indicate the power 1 has power.
P2 Green Indicate the power 2 has power.
Fault Green Indicate the either power 1 or power 2 has no power.
Per 10/100Base-TX Port
LED Color Function
Light Indicate the link through that port is successfully
established at 10 or 100Mbps.
LNK / ACT Green Blink Indicate that the Switch is actively sending or receiving
data over that port.
Per 100Base-FX Port
LED Color Function
Light Indicate the link through that port is successfully established
at 10 or 100Mbps.
LNK/ ACT Green Blink Indicate that the Switch is actively sending or receiving data
over that port.
-14 -

User’s Manual
PoE Port
LED Color Function
PoE In Use Orange Indicate the port is providing 48V DC in-line power. (1-4 ports)
2.1.4 Switch Upper Panel
The Upper Panel of the Industrial PoE Switch indicates a DC inlet power socket and consist one terminal block connector
within 6-contacts. It accepts input power from 24 or 48V DC.
Figure 2-3 Industrial PoE Switch Upper Panel
-15 -

User’s Manual
2.2 Install the switch
This section describes how to install your Managed Industrial Switch and make connections to the Managed Industrial
Switch. Please read the following topics and perform the procedures in the order being presented. To install your switch on
a desktop or shelf, simply complete the following steps.
In this paragraph, we will describe how to install the Industrial Switch and the installation points attended to it.
2.2.1 Installation Steps
1. Unpack the Industrial switch
2. Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not screwed on the Industrial
switch, please refer to DIN-Rail Mounting section for DIN-Rail installation. If users want to wall mount the Industrial
switch, please refer to Wall Mount Plate Mounting section for wall mount plate installation.
3. To hang the Industrial switch on the DIN-Rail track or wall.
4. Power on the Industrial switch. Please refer to the Wiring the Power Inputs section for knowing the information
about how to wire the power. The power LED on the Industrial switch will light up. Please refer to the LED Indicators
section for indication of LED lights.
5. Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.
6. Insert one side of RJ-45 cable (category 5) into the Industrial switch Ethernet port (RJ-45 port) and another side
of RJ-45 cable (category 5) to the network device’s Ethernet port (RJ-45 port), ex: Switch PC or Server. The UTP
port (RJ-45) LED on the Industrial switch will light up when the cable is connected with the network device. Please
refer to the LED Indicators section for LED light indication.
Make sure that the connected network devices support MDI/MDI-X. If it does not support, use
the crossover category-5 cable.
7. When all connections are set and LED lights all show in normal, the installation is complete.
2.2.2 DIN-Rail Mounting
This section describes how to install the Industrial PoE Switch.
There have two methods to install the Industrial PoE Switch. DIN-Rail Mounting and Wall Mount Plate Mounting. Please
read the following topics and perform the procedures in the order being presented.
-16 -

User’s Manual
Step 1: Screw the DIN-Rail on the Industrial PoE Switch.
Step 2: Lightly press the button of DIN-Rail into the track.
-17 -

User’s Manual
Step 3: Check the DIN-Rail is tightly on the track.
Please refer to following procedures to remove the Industrial PoE Switch from the track.
Step 5: Lightly press the button of DIN-Rail for remove it from the track.
-18 -

User’s Manual
2.2.3 Wall Mount Plate Mounting
To install the Industrial PoE Switch on the wall. Please follow the instructions below.
Step 1: Remove the DIN-Rail from the Industrial PoE Switch. Use the screwdriver to loose the screws and remove the
DIN-Rail.
Step 2: Place the wall mount plate on the rear panel of the Industrial PoE Switch.
Step 3: Use the screwdriver to screw the wall mount plate on the Industrial PoE Switch.
Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial PoE Switch on the wall.
Step 5: To remove the wall mount plate, reverse steps above.
2.3 Wiring the Power Inputs
The 6-contacts terminal block connector on the top panel of Industrial PoE Switch is used for two DC redundant power
inputs. Please follow the steps to insert the power wire. The PWR1 is 1(-) & 2(+) and PWR2 is 5(-) & 6(+) contact.
Remember: Tighten the wire-clamp screws for preventing the wires from loosing.
-19 -

User’s Manual
1 2 3 4 5 6
Power 1 Fault Power 2
- + - +
Figure 2-4: 6-Contacts of Terminal Block Connector
Power Notice: 1. The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG.
2. Performing any of the procedures like inserting the wires or tighten the wire-clamp screws. Ensure
the power is OFF to prevent to get an electric shock.
2.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle (3 & 4) of the terminal block connector as the picture shows below. Inserting the
wires, the Industrial PoE Switch will detect the fault status of the power failure, or port link failure (available for managed
model).
The following illustration shows an application example for wiring the fault alarm contacts
Power Notice:
1. The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG.
2. Performing any of the procedures like inserting the wires or tighten the wire-clamp screws. Ensure
the power is OFF to prevent to get an electric shock.
Insert the wires into the fault alarm contacts
-20 -