Planet Network Device WAP-4033PE User manual

54Mbps PoE Access Point
WAP-4033PE
User’s Manual

Copyright
Copyright ©2006 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting
from any defect in the software. Further, PLANET reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
1.Reorient or relocate the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4.Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance. (example-use only shielded interface cables when connecting to
computer or peripheral devices). Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
2
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any

interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to
the antenna shall not be less than 20 cm (8 inches) during normal operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal
Equipment and Satellite Earth Station Equipment) As of April 8,2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.
EU Countries Not Intended for Use
The ETSI version of this device is intended for home and office use in Austria Belgium, Denmark,
Finland, France (with Frequency channel restrictions). Germany, Greece, Ireland, Italy,
Luxembourg .The Netherlands, Portugal, Spain, Sweden and United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland.
Potential restrictive use
France: Only channels 10,11,12 and 13
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
3

Revision
User’s Manual for PLANET 54Mbps PoEAccess Point
Model: WAP-4033PE
Rev: 1.0 (Oct, 2006)
Part No. EM-WAP4033PE
4

TABLE OF CONTENTS
Chapter 1 Introduction ..................................................................................7
1.1 Package Contents.................................................................................................... 7
1.2 System Requirements.............................................................................................. 7
1.3 Features................................................................................................................... 8
1.4 LED Indicators.......................................................................................................... 8
1.5 Wireless Performance.............................................................................................. 8
1.6 Reset Button............................................................................................................. 9
Chapter 2 Hardware Installation.................................................................10
Chapter 3 Web Configuration .....................................................................11
3.1 Home.......................................................................................................................11
3.2 Basic Setting .......................................................................................................... 12
3.2.1 AP Mode.....................................................................................................................12
3.2.2 Station - Ad Hoc Mode................................................................................................14
3.2.3 Station - Infrastructure Mode......................................................................................16
3.2.4 AP Bridge - Point to Point Mode.................................................................................17
3.2.5 AP Bridge - Point to Multipoint Mode..........................................................................18
3.2.6 AP Bridge - WDS Mode..............................................................................................19
3.2.7 Universal Repeater Mode...........................................................................................21
3.2.8 Security setting of bridge mode..................................................................................22
3.3 Advanced Settings ................................................................................................. 24
3.4 Security .................................................................................................................. 25
3.4.1 802.1x.........................................................................................................................26
3.4.2 WEP...........................................................................................................................27
3.4.3 WPA pre-shared key...................................................................................................28
3.4.4 WPA RADIUS.............................................................................................................30
3.5 MAC Filtering.......................................................................................................... 31
3.6 System Utility.......................................................................................................... 32
3.7 Configuration Utility................................................................................................ 33
3.8 Upgrade.................................................................................................................. 34
3.9 Reset...................................................................................................................... 35
5

Chapter 4 Specification...............................................................................36
Chapter 5 Frequently Ask Question...........................................................37
6

Chapter 1 Introduction
Thank you for purchasing WAP-4033PE. The WAP-4033PE supports both IEEE 802.11b and IEEE
802.11g standards. You can use it to connect an existing WLAN, or to build up a new wireless LAN.
Except for essential AP mode, WAP-4033PE also provides AP Client/ Bridge/ Repeater and WDS
(Wireless Distributed System) modes to accommodate all kinds of network topology. High data rate (up to
54Mbps) support allows faster communication between LAN and WLAN. Maximize network efficiency
while minimizing your network investment and maintenance costs. With the PoE (IEEE802.3af) interface,
users can easily connect this AP to anywhere.
\
Supports WPA, WPA2, WEP and MAC address filter function to consolidate the wireless network security,
you can prevent unauthorized wireless stations from accessing your wireless network.
This product provides a friendly user interface and allows users to configuring from web browser. Without
utility install, user doesn’t need to find the utility for this product in lots of program list, it can be configured
in different OS that has provide web browser.
1.1 Package Contents
Make sure that you have the following items:
z1 x WAP-4033PE
z1 x Power Adapter
z1 x User’s Manual CD
z1 x Quick Installation Guide
z1 x External Antenna
Note: If any of the above items are missing, contact your supplier as soon as
possible.
1.2 System Requirements
Before installation, please check the following requirements with your equipment.
zPentium Based (or above) IBM-Compatible PC System
zCD-ROM drive
zWindows 98/Me/NT/2000/XP/Server2003 Operating System with TCP/IP protocol
7

1.3 Features
zComplies with the IEEE 802.11b/g (DSSS) 2.4GHz specification
zSupports 2.400~2.4835 GHz frequency band
zData rate supports up to 54Mbps
zIEEE 802.3af compliant
zAuto rate fallback in case of obstacles or interferences
zSupports WEP/WPA-PSK/WPA/WPA2 encryption
zSupports AP/ AP Client/ Bridge/ Repeater and WDS (Wireless Distributed System) mode
zSeamlessly integrate wireless and wired Ethernet LAN networks
zProvides MAC Filter function
zBuilt-in DHCP server
zSupport Auto-MDI/MDI-X
zWeb-based configuration
1.4 LED Indicators
LED Color Function
PWR Green Off: Power is not connected
On: Device is ready
Blink: During boot up procedure
WLAN Green Off: Wireless LAN is no function
Blink: Transmitting or receiving data through the Wireless LAN
LAN Green Off: LAN is not connected
On: LAN is connected
Blink: Transmitting or receiving data through the LAN
1.5 Wireless Performance
The following information will help you utilizing the wireless performance and operating coverage of
WAP-4033PE.
1. Site selection
To avoid interferences, please locate WAP-4033PE and wireless client away from transformers,
8

microwave ovens, heavy-duty motors, fluorescent lights and other industrial equipments. Keep the
number of walls or ceilings between AP and clients as few as possible. Otherwise the signal strength
may be seriously reduced. Place WAP-4033PE in a open space or add additional WAP-4033PE as
needed to improve the coverage.
2. Environmental factors
The wireless network is easily affected by many environment factors. Every environment is unique
with different obstacles, construction materials, weather, etc. It is hard to determine the exact
operation rage of WAP-4033PE in a specific location without testing.
3. Antenna adjustment
The bundle antenna of WAP-4033PE is adjustable. Firstly install the antenna pointing straight up,
then smoothly adjust it if the radio signal strength is poor. But the signal reception is definitely weak
in some certain areas, such as location right down the antenna.
Moreover, the original antenna of WAP-4033PE can be replaced with other external antennas to
extend the coverage. Please check the specification of the antenna you want to use, and make sure
it can be used on WAP-4033PE.
4. WLAN Type
If WAP-4033PE is installed in an 802.11b and 802.11g mixed WLAN, its performance will reduced
significantly. Because every 802.11g OFDM packet needs to be preceded by an RTS-CTS or CTS
packet exchange that can be recognized by legacy 802.11b devices. This additional overhead
lowers the speed. If there are no 802.11b devices connected, or if connections to all 802.11b devices
are denied so that WAP-4033PE can operate in 11g-only mode, then its data rate should actually
54Mbps.
1.6 Reset Button
WAP-4033PE provides a Reset button on the rear panel for user to reset or set WAP-4033PE
configuration to factory default by hardware.
Time Active
Press less than 5 Sec. WAP-4033PE will re-boot itself, keeping your original configurations
Press more than 5 Sec. WAP-4033PE will reset itself to the factory default settings
9

Chapter 2 Hardware Installation
Before you proceed with the installation, it is necessary that you have enough information about the
WAP-4033PE.
1. Locate an optimum location for the WAP-4033PE. The best place for your WAP-4033PE is
usually at the center of your wireless network, with line of sight to all of your mobile stations.
2. Assemble the antenna to WAP-4033PE. Try to place them to a position that can best cover your
wireless network. The antenna’s position will enhance the receiving sensitivity.
3. Connect RJ-45 cable to WAP-4033PE. Connect this WAP-4033PE to your LAN switch/hub or a
single PC. If the connected device is IEEE802.3af compliant switch, the WAP-4033PE will power
on. You will not need to plug-in the power adapter in next step.
4. Plug in power adapter and connect to power source. After power on, WAP-4033PE will start to
work.
Note: ONLY use the power adapter supplied with the WAP-4033PE. Otherwise, the product may
be damaged. If you want to reset your WAP-4033PE to default settings, press the Reset
button 5 second. Then release the button and wait for 10 seconds for rebooting.
1
0

Chapter 3 Web Configuration
Web configuration provides a user-friendly graphical user interface (web pages) to manage your
WAP-4033PE. An AP with an assigned IP address (e.g. http://192.168.0.1) will allow you to monitor and
configure (via web browser e.g., MS Internet Explorer or Netscape).
1. Open your web browser.
2. Enter WAP-4033PE IP address (default IP address is http://192.168.0.1) into the address field of the
web browser. Please also make sure your PC’s IP address is in the same IP range with WAP-4033PE.
3. A User Name and Password dialog box will appear. Please enter your User Name and Password here.
Default User Name and Password are “admin”. Click “OK”.
4. When enter correct User Name and Password, you will see the configuration screen as section 3.1.
3.1 Home
In this screen, you can check all the information of WAP-4033PE.
11

3.2 Basic Setting
In this option, you can configure WAP-4033PE to work to different operating mode. Please refer
to below sections to know the details configuration of each operating mode.
3.2.1 AP Mode
This mode is set to WAP-4033PE by default. It served as a transparent Media Access Control
(MAC) bridge between wired and wireless network.
12

Parameter Description
Mode Shows the current operation mode. You may set WAP-4033PE to other operating
mode by select other operating mode.
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps.
2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
2.4GHz (B+G): It provides best performance for 11g transmission when you enable
the AP mode selection to “Mixed mode”.
SSID The SSID (up to 32 printable ASCII characters) is the unique name identified in a
WLAN. The ID prevents the unintentional merging of two co-located WLANs.
Please make sure that the SSID of all stations in the same WLAN network are the
same. The default SSID is “default”.
Channel Number Select the appropriate channel from the list provided to correspond with your
network settings. Channels differ from country to country.
Channel 1-11 (North America)
Channel 1-14 (Japan)
Channel 1-13 (Europe)
Associated Clients You may press “Show Active Clients” button to check the connected client
information. After the button pressed, you will see the dialog box as below.
You may press “Refresh” to get the new client table or “Close” to close this dialog
box.
After configuration complete, please click “Apply” button to save the configuration. Then you will
see a screen to prompt you the settings are save successfully. You may press “Continue” for
configure other settings or “Apply” to restart WAP-4033PE with new configuration. This screen
will appear after press the “Apply” button in each configuration screen. When you complete all
the configuration of WAP-4033PE, please press “Apply” of this screen to make the new settings
13

work. You may check the LED status to make sure WAP-4033PE is finish the restart.
3.2.2 Station - Ad Hoc Mode
Served as a wireless station (Ad-hoc). Connected to a PC or a small LAN, this station along
with other wireless stations can establish a small wireless network without Access Points.
14

Parameter Description
Mode Shows the current operation mode. You may set WAP-4033PE to other
operating mode by select other operating mode.
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps.
2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
2.4GHz (B+G): It provides best performance for 11g transmission when
you enable the AP mode selection to “Mixed mode”.
SSID Please make sure the SSID of the wireless network that you will
connected and enter the correct SSID in this field. The default SSID is
“default”.
Channel Number Select the appropriate channel from the list provided to correspond with
your network settings. Channels differ from country to country.
Channel 1-11 (North America)
Channel 1-14 (Japan)
Channel 1-13 (Europe)
WLAN MAC Keep default setting: WAP-4033PE will use it’s own MAC address to
access the wireless LAN.
Press “MAC Clone” button: It will use PC’s MAC address to access the
wireless LAN.
After configuration complete, please click “Apply” button to save the configuration. Then you will
see a screen to prompt you the settings are save successfully. You may press “Continue” for
configure other settings or “Apply” to restart WAP-4033PE with new configuration.
1
5

3.2.3 Station - Infrastructure Mode
Served as a wireless station (infrastructure). Connected to a PC or a small LAN, it allows the
PC or small LAN able to access the wireless network via Access Point.
Parameter Description
Mode Shows the current operation mode. You may set WAP-4033PE to other
operating mode by select other operating mode.
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps.
2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
2.4GHz (B+G): It provides best performance for 11g transmission when
you enable the AP mode selection to “Mixed mode”.
SSID Please make sure the SSID of the wireless network that you will
connected and enter the correct SSID in this field. The default SSID is
“default”.
WLAN MAC Keep default setting: WAP-4033PE will use it’s own MAC address to
access the wireless LAN.
Press “MAC Clone” button: It will use PC’s MAC address to access the
wireless LAN.
After configuration complete, please click “Apply” button to save the configuration. Then you will
see a screen to prompt you the settings are save successfully. You may press “Continue” for
configure other settings or “Apply” to restart WAP-4033PE with new configuration.
1
6

3.2.4 AP Bridge - Point to Point Mode
This function provides to bridge for 2 wired Ethernet networks to connect to each other by
wireless. You can use two WAP-4030s in this mode to connect two wired Ethernet networks
together.
Parameter Description
Mode Shows the current operation mode. You may set WAP-4033PE to other operating
mode by select other operating mode.
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps.
2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
2.4GHz (B+G): It provides best performance for 11g transmission when you
enable the AP mode selection to “Mixed mode”.
Channel Number Select the appropriate channel from the list provided to correspond with your
network settings. Channels differ from country to country.
Channel 1-11 (North America)
Channel 1-14 (Japan)
Channel 1-13 (Europe)
MAC Address 1 Keep default setting: WAP-4033PE will use it’s own MAC address to access the
wireless LAN.
Press “MAC Clone” button: It will use PC’s MAC address to access the
wireless LAN.
Set Security IF you want to enable security to protect your wireless connection. Please press
“Set Security” button and refer to section “3.2.8 Security setting for bridge mode”
1
7

to configure the detail settings.
After configuration complete, please click “Apply” button to save the configuration. Then you will
see a screen to prompt you the settings are save successfully. You may press “Continue” for
configure other settings or “Apply” to restart WAP-4033PE with new configuration.
3.2.5 AP Bridge - Point to Multipoint Mode
This function provides to bridge more than 2 wired Ethernet networks together by wireless
connection. You can use more than two WAP-4033PE with this mode to connect those wired
Ethernet networks together.
Parameter Description
Mode Shows the current operation mode. You may set WAP-4033PE to other operating
mode by select other operating mode.
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps.
2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
2.4GHz (B+G): It provides best performance for 11g transmission when you enable
the AP mode selection to “Mixed mode”.
Channel Number Select the appropriate channel from the list provided to correspond with your
network settings. Channels differ from country to country.
Channel 1-11 (North America)
Channel 1-14 (Japan)
Channel 1-13 (Europe)
18

AP MAC Address If you want to bridge more than two wired Ethernet networks together with wireless
connection, you have to enter the MAC addresses of otherWAP-4033PEs that with
join the bridging work into the fields.
Set Security IF you want to enable security to protect your wireless connection. Please press
“Set Security” button and refer to section “3.2.8 Security setting for bridge mode” to
configure the detail settings.
After configuration complete, please click “Apply” button to save the configuration. Then you will see
a screen to prompt you the settings are save successfully. You may press “Continue” for configure
other settings or “Apply” to restart WAP-4033PE with new configuration.
3.2.6 AP Bridge - WDS Mode
If you want an access point to bridge wired Ethernet network and provide connection service for
other wireless bridge at the same time, you have to set the WAP-4033PE to “AP Bridge - WDS”.
Simply speaking, “AP Bridge - WDS” function is the combination of “AP mode” and “AP
Bridge-Point to Multi-Point mode”.
Parameter Description
Mode Shows the current operation mode. You may set WAP-4033PE to other operating
mode by select other operating mode.
19

Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps.
2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
2.4GHz (B+G): It provides best performance for 11g transmission when you enable
the AP mode selection to “Mixed mode”.
SSID The SSID (up to 32 printable ASCII characters) is the unique name identified in a
WLAN. The ID prevents the unintentional merging of two co-located WLANs.
Please make sure that the SSID of all stations in the same WLAN network are the
same. The default SSID is “default”.
Channel Number Select the appropriate channel from the list provided to correspond with your
network settings. Channels differ from country to country.
Channel 1-11 (North America)
Channel 1-14 (Japan)
Channel 1-13 (Europe)
Associated Clients You may press “Show Active Clients” button to check the connected client
information. After the button pressed, you will see the dialog box as below:
You may press “Refresh” to get the new client table or “Close” to close this dialog
box.
MAC Address 1 ~6 If you want to bridge more than two wired Ethernet networks together with wireless
connection, you have to enter the MAC addresses of otherWAP-4033PEs that with
join the bridging work into the fields.
Set Security IF you want to enable security to protect your wireless connection. Please press
“Set Security” button and refer to section “3.2.8 Security setting for bridge mode” to
configure the detail settings.
After configuration complete, please click “Apply” button to save the configuration. Then you will
2
0