Planet WNAP-W2201A User manual

Copyright
Copyright 2016 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting
from any defect in the software. Further, PLANET reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.
I

Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive
repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU
directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reasons/remarks
Bulgaria None General authorization required for outdoor use and
public service
France
Outdoor use; limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply (not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian
Federation
None Only for indoor applications
Note: Please don’t use the product outdoors in France.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
I

Revision
User Manual of PLANET 300Mbps 802.11n Wireless In-wall PoE Access Point
Model: WNAP-W2201A
Rev: 1.0 (February, 2016)
Part No. EM-WNAP-W2201A_v1.0
II

CONTENTS
Chapter 1.Product Introduction...........................................................................................................1
1.1Package Contents ...............................................................................................................1
1.2Product Description............................................................................................................2
1.3Product Features................................................................................................................. 5
1.4Product Specifications ....................................................................................................... 6
Chapter 2.Hardware Introduction ........................................................................................................ 9
2.1Product Outlook ..................................................................................................................9
2.1.1Panel Layout.............................................................................................................9
2.1.2Hardware Description .............................................................................................10
Chapter 3.Hardware Installation ........................................................................................................ 11
3.1Installing the AP ................................................................................................................ 11
3.1.1Installing the AP – WNAP-W2201A ........................................................................ 11
Chapter 4.Connect to the AP ............................................................................................................. 13
4.1System Requirements ......................................................................................................13
4.2Manual Network Setup -- TCP/IP Configuration.............................................................13
4.2.1Configuring the IP Address Manually .....................................................................14
4.3Starting Setup in the Web UI ............................................................................................17
Chapter 5.Configuring the AP............................................................................................................18
5.1Operation Mode.................................................................................................................18
5.2Setup Wizard......................................................................................................................20
5.3TCP/IP Settings..................................................................................................................25
5.3.1LAN Settings...........................................................................................................25
5.4WLAN..................................................................................................................................27
5.4.1Basic Settings .........................................................................................................27
5.4.2Advanced Settings..................................................................................................44
5.4.3RF Output Power....................................................................................................46
5.4.4Security...................................................................................................................47
5.4.5Access Control........................................................................................................49
5.4.6WDS........................................................................................................................51
5.4.7Site Survey .............................................................................................................54
5.4.8WPS........................................................................................................................55
5.4.9Schedule.................................................................................................................59
5.5Management ......................................................................................................................61
5.5.1Status......................................................................................................................61
5.5.2Statistics..................................................................................................................63
5.5.3SNMP......................................................................................................................64
III

5.5.4NTP Settings...........................................................................................................65
5.5.5Schedule Reboot ....................................................................................................67
5.5.6LOG ........................................................................................................................69
5.5.7Upgrade Firmware..................................................................................................70
5.5.8Reload Settings ......................................................................................................70
5.5.9Password ................................................................................................................72
5.5.10LED Control ............................................................................................................73
5.5.11Logout.....................................................................................................................74
5.5.12Reboot ....................................................................................................................74
Chapter 6.Quick Connection to a Wireless Network.......................................................................75
6.1Windows XP (Wireless Zero Configuration)...................................................................75
6.2Windows 7 (WLAN AutoConfig).......................................................................................77
6.3Mac OS X 10.x.................................................................................................................... 80
6.4iPhone/iPod Touch/iPad ...................................................................................................84
Appendix A: Planet Smart Discovery Utility..................................................................................... 87
Appendix B: FAQs...............................................................................................................................88
Q1: How to set up the WDS Repeater Connection..................................................................88
Q2: How to set up the Universal Repeater Connection.......................................................... 96
Appendix C: Troubleshooting..........................................................................................................103
Appendix D: Glossary.......................................................................................................................105
IV

FIGURE
FIGURE 2-1 WNAP-W2201AFRONT PANEL ..........................................................................................................9
FIGURE 2-2 WNAP-W2201AREAR PANEL............................................................................................................9
FIGURE 3-1 WNAP-W2200 INSTALLATION DIAGRAM 1.......................................................................................11
FIGURE 3-2 WNAP-W2201AINSTALLATION DIAGRAM 2....................................................................................12
FIGURE 3-3 WNAP-W2201AINSTALLATION DIAGRAM 3....................................................................................12
FIGURE 4-1 TCP/IPSETTING................................................................................................................................14
FIGURE 4-2 WINDOWS START MENU ....................................................................................................................15
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND .........................................................................................15
FIGURE 4-4 FAILED RESULT OF PING COMMAND ..................................................................................................16
FIGURE 4-5 LOGIN BY DEFAULT IPADDRESS........................................................................................................17
FIGURE 4-6 LOGIN WINDOW ................................................................................................................................17
FIGURE 5-1 MAIN MENU ......................................................................................................................................18
FIGURE 5-2 OPERATION MODE .............................................................................................................................19
FIGURE 5-3 SETUP WIZARD..................................................................................................................................20
FIGURE 5-4 LAN INTERFACE SETUP TOPOLOGY...................................................................................................20
FIGURE 5-5WIZARD –LAN INTERFACE SETUP....................................................................................................20
FIGURE 5-6 TIME ZONE SETUP TOPOLOGY ...........................................................................................................21
FIGURE 5-7WIZARD –TIME ZONE SETUP ............................................................................................................21
FIGURE 5-8 WIZARD –WIRELESS BASIC SETTINGS ..............................................................................................22
FIGURE 5-9 WIZARD –WIRELESS SECURITY SETUP .............................................................................................23
FIGURE 5-10WIRELESS SECURITY SETUP –WEPSETTING ..................................................................................23
FIGURE 5-11 WIRELESS SECURITY SETUP –WPASETTING...................................................................................24
FIGURE 5-12 LAN SETTING..................................................................................................................................25
FIGURE 5-13WIRELESS MAIN MENU ...................................................................................................................27
FIGURE 5-14WIRELESS BASIC SETTINGS –AP.....................................................................................................28
FIGURE 5-15WIRELESS BASIC SETTINGS –MULTIPLE APS..................................................................................30
FIGURE 5-16MULTIPLE-SSIDS............................................................................................................................31
FIGURE 5-17UNIVERSAL REPEATER-1 .................................................................................................................32
FIGURE 5-18UNIVERSAL REPEATER-2 .................................................................................................................32
FIGURE 5-19UNIVERSAL REPEATER-3 .................................................................................................................33
FIGURE 5-20UNIVERSAL REPEATER-4 .................................................................................................................33
FIGURE 5-21UNIVERSAL REPEATER-5 .................................................................................................................33
FIGURE 5-22WIRELESS BASIC SETTINGS –CLIENT..............................................................................................34
FIGURE 5-23 CLIENT –SURVEY ............................................................................................................................36
FIGURE 5-24 CLIENT –APLIST ............................................................................................................................37
FIGURE 5-25 CLIENT –SECURITY.........................................................................................................................38
FIGURE 5-26 CLIENT –STATUS .............................................................................................................................38
FIGURE 5-27WIRELESS BASIC SETTINGS –WDS.................................................................................................40
FIGURE 5-28WIRELESS BASIC SETTINGS –REPEATER .........................................................................................42
FIGURE 5-29WIRELESS ADVANCED SETTINGS .....................................................................................................44
FIGURE 5-30 RF OUTPUT POWER .........................................................................................................................46
FIGURE 5-31WIRELESS SECURITY SETTINGS .......................................................................................................47
V

FIGURE 5-32WIRELESS ACCESS CONTROL...........................................................................................................49
FIGURE 5-33WIRELESS ACCESS CONTROL –DENY..............................................................................................50
FIGURE 5-34WDS MODE.....................................................................................................................................52
FIGURE 5-35WDS SETTINGS ...............................................................................................................................52
FIGURE 5-36WDS –SET SECURITY .....................................................................................................................53
FIGURE 5-37 SITE SURVEY ...................................................................................................................................54
FIGURE 5-38WPS................................................................................................................................................55
FIGURE 5-39WPS-PBC -1...................................................................................................................................57
FIGURE 5-40WPS-PBC -2...................................................................................................................................57
FIGURE 5-41WPS-PIN -1.....................................................................................................................................58
FIGURE 5-42WPS-PIN -2.....................................................................................................................................58
FIGURE 5-43WPS-PIN -3.....................................................................................................................................58
FIGURE 5-44 SCHEDULE .......................................................................................................................................60
FIGURE 5-45MANAGEMENT –MAIN MENU .........................................................................................................61
FIGURE 5-46 STATUS ............................................................................................................................................62
FIGURE 5-47 STATISTICS .......................................................................................................................................63
FIGURE 5-48 SNMP .............................................................................................................................................64
FIGURE 5-49 TIME ZONE SETTINGS ......................................................................................................................65
FIGURE 5-50 SCHEDULE REBOOT .........................................................................................................................67
FIGURE 5-51 SCHEDULE REBOOT -EXAMPLE.......................................................................................................68
FIGURE 5-52 SYSTEM LOG ...................................................................................................................................69
FIGURE 5-53UPGRADING FIRMWARE...................................................................................................................70
FIGURE 5-54 SAVE/RELOAD SETTINGS .................................................................................................................71
FIGURE 5-55PASSWORD SETUP............................................................................................................................72
FIGURE 5-56 LED CONTROL ................................................................................................................................73
FIGURE 5-57 LOGOUT...........................................................................................................................................74
FIGURE 5-58 REBOOT...........................................................................................................................................74
FIGURE 6-1 SYSTEM TRAY –WIRELESS NETWORK ICON......................................................................................75
FIGURE 6-2 CHOOSING A WIRELESS NETWORK ....................................................................................................75
FIGURE 6-3 ENTERING THE NETWORK KEY..........................................................................................................76
FIGURE 6-4 CHOOSING A WIRELESS NETWORK -- CONNECTED ............................................................................76
FIGURE 6-5 NETWORK ICON.................................................................................................................................77
FIGURE 6-6WLANAUTOCONFIG ........................................................................................................................77
FIGURE 6-7TYPING THE NETWORK KEY ..............................................................................................................78
FIGURE 6-8 CONNECTING TO A NETWORK ............................................................................................................78
FIGURE 6-9 CONNECTED TO A NETWORK..............................................................................................................79
FIGURE 6-10MAC OS –NETWORK ICON..............................................................................................................80
FIGURE 6-11 HIGHLIGHTING AND SELECTING THE WIRELESS NETWORK..............................................................80
FIGURE 6-12 ENTER THE PASSWORD ....................................................................................................................81
FIGURE 6-13 CONNECTED TO THE NETWORK .......................................................................................................81
FIGURE 6-14 SYSTEM PREFERENCES ....................................................................................................................82
FIGURE 6-15 SYSTEM PREFERENCES -- NETWORK................................................................................................82
FIGURE 6-16 SELECTING THE WIRELESS NETWORK .............................................................................................83
FIGURE 6-17 IPHONE –SETTINGS ICON.................................................................................................................84
FIGURE 6-18WI-FI SETTING ................................................................................................................................84
VI

VII
FIGURE 6-19WI-FI SETTING –NOT CONNECTED .................................................................................................85
FIGURE 6-20TURNING ON WI-FI..........................................................................................................................85
FIGURE 6-21 IPHONE -- ENTERING THE PASSWORD...............................................................................................86
FIGURE 6-22 IPHONE -- CONNECTED TO THE NETWORK .......................................................................................86

User Manual of WNAP-W2201A
-1-
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WNAP-W2201A. Before installing the AP, please verify the contents inside the
package box.
WNAP-W2201A Screw x 2
Quick Guide
If there is any item missing or damaged, please contact the seller immediately.

User Manual of WNAP-W2201A
-2-
1.2 Product Description
All-in-One Manageable Wi-Fi Solution for Hospitality Industry
PLANET WNAP-W2201A enables hospitality industry to build a high-speed wireless network with a maximum
data rate of 11n 300Mbps via PLANET AP controller. Furthermore, it conforms to standard 86-type electrical
junction box and IEEE 802.3af PoE, suitable for in-wall installation. The WNAP-W2201A has also a built-in RJ11
port for phone pass-through and 100BASE-TX RJ45 port for Ethernet connection to such device as IPTV or laptop,
enabling to integrate a hotel network with its all-in-one interface. This definitely helps guests gain good user
experience.
Ease of Deployment with PLANET AP Controller
To expand the capability of in-wall AP, PLANET WNAP-W2201A comes with centralized management, enabling
the hospitality industry to deploy multiple APs with a single interface of AP controller and reducing repetitive
tasks including AP provisioning, AP status monitoring and AP maintenance. In addition, by connecting with
PLANET WAPC AP controller series, the WNAP-W2201A comes with PoE alive check and PoE schedule
features, which help hoteliers optimize their wireless network within minutes.

User Manual of WNAP-W2201A
-3-
Suitable for Any Room Installation without Breaking Interior Design
Featuring attractive in-wall design, the WNAP-W2201A can be firmly installed into the wall via the standard 86 x
86 mm or 75 x 75 mm European outlet box, which makes electrical wiring invisible and convenient for room
installation without affecting the original interior design. It is ideal for hotels, residences, hospitals and more to
establish wireless network.
Comprehensive Wireless Operation Mode
The WNAP-W2201A supports multiple wireless communication connectivities such as AP (Multi-SSIDs), Client,
Repeater/Universal Repeater, WDS Point-to-Point (PtP) and WDS Point-to-Multipoint (PtMP), allowing
users to comprehensively experience various applications.

User Manual of WNAP-W2201A
-4-
Easy to Install and Manage
Integrated with RJ11 phone pass-through, RJ45 Ethernet connection and IEEE 802.3af PoE PD scheme, the
WNAP-W2201A is easy to be installed to any room’s existing 86-type or 75-type junction box with only 6 steps.
The setup wizard and on-line help can simplify the configuration even for a user who has never experienced in
setting up a wireless network. In aspect of centralized management, besides the SNMP, multiple devices can be
configured and monitored by PLANET AP controller. The WNAP-W2201A helps the system administrator
overcome the difficulties of wireless deployment.
Easy 6-Step Installation
Dismantle the existing panel in the wall
1Connect network cable to
the PoE Port
2
PoE
LAN
RJ11
Connect Phone wire to
the RJ11 Port
3
PoE
LAN
RJ11
Open the front panel
4Screw the AP on the wall 5Place the front panel over AP to
tightly close, and turn it on
6

User Manual of WNAP-W2201A
-5-
1.3 Product Features
Standard Compliant Hardware Interface
Compliant with IEEE 802.11n wireless technology with data rate of up to 300Mbps
One 10/100BASE-TX port and one PoE powered device (PD) port
One RJ11 port for phone line connection
European 86-type and 75-type wall outlet compatibility
Secure Network Connection
Advanced security: 64-/128-bit WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK (TKIP/AES
encryption), 802.1x
Supports wireless MAC address filtering control to limit the connected wireless clients
Comprehensive Wireless Advanced Features
Multiple operation modes including AP (Multi-SSIDs), Client, Repeater/Universal Repeater, WDS
Point-to-Point (PtP) and WDS Point-to-Multipoint (PtMP)
Up to 5 multiple-SSIDs to allow users to access different networks through a single AP
Supports WMM (Wi-Fi Multimedia) and wireless QoS to enhance the efficiency of multimedia
application
Supports IAPP (Inter Access Point Protocol) wireless roaming to enable clients to roam across
multiple APs
Provides 5-level Transmit Power Control to adapt various environments
Wireless schedule allows administrators to enforce time-based internet access
Self-healing (Schedule Reboot) mechanism for reliable connection
Easy Deployment & Centralized Management
Supports AP controller to enable administrator to configure and monitor multiple APs
simultaneously
Flexible deployment with standard 802.3af PoE/PD supported
Stylish in-wall design perfectly matches the room decoration
Step-by-step configuration with intelligent setup wizard and graphical Web-based UI
Supports SNMP-based management interface
System status monitoring including associated client list and system log

User Manual of WNAP-W2201A
-6-
1.4 Product Specifications
Product WNAP-W2201A
300Mbps 802.11n Wireless In-wall PoE Access Point
Hardware Specifications
PoE Port 1 x 10/100Mbps auto MDI/MDI-X RJ45 port (rear panel)
※IEEE 802.3af PoE PD Port
LAN Port 1 x 10/100Mbps auto MDI/MDI-X RJ45 port
Interface
RJ11 Port Connect to the telephone through the 4-conductor phone line
PoE 802.3af PoE PD, Class 3
Antenna Built-in 3dBi antenna x 2
Reset Button Reset button on side panel
(Press over 5 seconds to reset the device to factory default)
LED Indicators PWR/SYS LED
Material Plastic
Dimensions (W x D x H) 86 x 35 x 86 mm
Weight 76g
Power Requirements 802.3af/at PoE, 48-56V DC input, 0.35A (max.)
Power Consumption < 10W
Wireless interface Specifications
Standard Compliant with IEEE 802.11b/g/n
Frequency Band Europe -- ETSI: 2.412~2.472GHz
Operating Channel Europe -- ETSI: 1~13
Channel Width 20 or 20/40MHz
Data Transmission
Rates
802.11n (HT40): 270/243/216/162/108/81/54/27Mbps
135/121.5/108/81/54/40.5/27/13.5Mbps (dynamic)
802.11n (HT20): 130/117/104/78/52/39/26/13Mbps
65/58.5/52/39/26/19.5/13/6.5Mbps (dynamic)
802.11g: 54/48/36/24/18/12/9/6Mbps (dynamic)
802.11b: 11/5.5/2/1Mbps (dynamic)
Transmission Distance
802.11n: up to 70m
802.11g: up to 30m
The estimated transmission distance is based on the theory.
The actual distance will vary in different environments.
Max. RF Power
802.11n: 17 ± 2dBm
802.11g: 17 ± 2dBm
802.11b: 18 ± 2dBm
Receiver Sensitivity
IEEE 802.11b: -92dBm @ 1Mbps; -85dBm @ 11Mbps, PER < 8%
IEEE 802.11g: -88dBm @ 6Mbps; -73dBm @ 54Mbps, PER <10%
IEEE 802.11n: -90dBm @ MCS8; -70dBm @ MCS15, PER <10%
Data Rate
IEEE 802.11b: 1/2/5.5/11Mbps
IEEE 802.11g: 6/9/12/18/24/36/48/54Mbps
IEEE 802.11n: 300 Mbps in 40MHz mode/150Mbps in 20MHz mode
TX Power Provides 5-level Tx Power Control (100%, 70%, 50%, 35%, 15%)

User Manual of WNAP-W2201A
-7-
Wireless Management Features
Operation Mode Standalone AP
Managed AP
Wireless Mode
AP (Multiple-SSIDs)
Client
Repeater (WDS+AP)
Universal Repeater (AP+Client)
WDS PtP Bridge
WDS PtMP Bridge
Encryption Security
WEP (64-/128-bit) encryption security
WPA/WPA2 (TKIP/AES)
WPA-PSK/WPA2-PSK (TKIP/AES)
802.1x RADIUS Authentication
Wireless MAC address filtering (up to 20 entries)
Supports WPS (Wi-Fi Protected Setup)
Wireless Security
SSID broadcast and hide
Supports WMM (Wi-Fi Multimedia) for better data transmission of video or
on-line demand
Supports wireless schedule
Multiple SSIDs: up to 5
Wireless Isolation: Enables it to isolate each connected wireless client of a
BSSID from communicating with each other
IAPP (Inter Access Point Protocol): 802.11f wireless roaming
Wireless Advanced
Provides wireless statistics, max. associated station number
Max. Supported Clients Wired: 253
2.4GHz Wireless: 32
Built-in DHCP server supporting static IP address distribution
Supports static IP and dynamic IP
Supports UPnP
LAN
Supports 802.1d Spanning Tree
Web-based (HTTP) management interface
Supports SNTP synchronization
Easy firmware upgrade via HTTP/TFTP (through AP controller)
Easily locate deployed APs through the LED control
Supports SNMP management, LED On/Off control, Schedule Reboot
Supports Smart Discovery Utility, System Log
System Management
Supports WAPC series of AP controllers for central management
Max. WDS Peers 8
IEEE Standards
IEEE 802.11n (2T2R, up to 300Mbps)
IEEE 802.11g
IEEE 802.11b
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x flow control
Other Protocols and CSMA/CA, CSMA/CD, TCP/IP, DHCP, ICMP, SNTP

User Manual of WNAP-W2201A
-8-
Standards
Environment & Certification
Temperature Operating: -10 ~ 50 degrees C
Storage: -40 ~ 70 degrees C
Humidity Operating: 10 ~ 90% (non-condensing)
Storage: 5 ~ 90% (non-condensing)
Regulatory CE, RoHS

User Manual of WNAP-W2201A
-9-
Chapter 2. Hardware Introduction
2.1 Product Outlook
Dimensions: 86 x 35 x 86 mm
2.1.1 Panel Layout
The front and rear panels provide a simple interface monitoring the AP.
Front Panel
Figure 2-1 WNAP-W2201A Front Panel
Rear Panel
Figure 2-2 WNAP-W2201A Rear Panel

User Manual of WNAP-W2201A
-10-
2.1.2 Hardware Description
LED Definition
LED COLOR STATUS FUNCTION
Green On Device power on
Green Flash Detect and identify the LED (controlled by S/W)
PWR
Green Off Device power off (controlled by S/W)
Button definition
Object Description
Reset Press the Reset button for over 5 seconds and then release it to restore system
to the factory default settings.
H/W Interface definition
Object Description
PoE Port
(802.3af/at PoE)
10/100bps RJ45 port, auto MDI/ MDI-X
Connect PoE port to the IEEE 802.3af/at PoE switch to power on the device.
LAN Port
10/100Mbps RJ45 port, auto MDI/ MDI-X
Connect this port to the network equipment.
RJ11 Port Connect to the telephone through the 4-conductor RJ11 phone line

User Manual of WNAP-W2201A
-11-
Chapter 3.Hardware Installation
3.1 Installing the AP
Before installing the AP, make sure your PoE switch is connected to the Internet through the broadband service
successfully at this moment. If there is any problem, please contact your local ISP. After that, please install the
AP according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
3.1.1 Installing the AP – WNAP-W2201A
Step 1. Follow the figure below to install WNAP-W2201A.
Figure 3-1 WNAP-W2200 Installation Diagram 1
※The Ethernet cable should not exceed 8cm in length from the end connecting to PoE port to the part
that goes through the outlet box.
Easy 6-Step Installation
Dismantle the existing panel in the wall
1Connect network cable to
the PoE Port
2
PoE
LAN
RJ11
Connect Phone wire to
the RJ11 Port
3
PoE
LAN
RJ11
Open the front panel
4Screw the AP on the wall 5Place the front panel over AP to
tightly close, and turn it on
6