Planet WNAP-6305 User manual

User’s Manual of WNAP-6305
- 1 -

User’s Manual of WNAP-6305
Copyright
Copyright 2011 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution:
To assure continued compliance, (example-use only shielded interface cables when connecting to
computer or peripheral devices) any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may cause
undesired operation.
- 2 -

User’s Manual of WNAP-6305
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the DC-plug to disconnect the device from the power circuit.
Without remove the DC-plug, the device still consuming power from the power circuit. In the view of
Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to
remove the DC-plug for the device if this device is not intended to be active.
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950 has been conducted. These are considered
relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article 3.1b
Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-17 and EN 55024
has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered
relevant and sufficient.
CE in which Countries where the product may be used freely:
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg,
Austria, Finland, Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits the use of other channels.
- 3 -

User’s Manual of WNAP-6305
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications
Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the
EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Bulgaria None General authorization required for outdoor use and
public service
France Outdoor use limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian Federation None Only for indoor applications
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
- 4 -

User’s Manual of WNAP-6305
Revision
User’s Manual for PLANET 802.11n Wireless Outdoor Access Point
Model: WNAP-6305
Rev: 1.0 (June, 2011)
- 5 -

User’s Manual of WNAP-6305
Table of Contents
Chapter 1. Product Introduction..........................................................................................................9
1.1 Package contents..................................................................................................................9
1.2 Product Description..............................................................................................................9
1.3 Product Features................................................................................................................. 11
1.4 Product Specification .........................................................................................................12
1.5 Wireless Performance ........................................................................................................14
Chapter 2. Hardware Description ......................................................................................................15
2.1 The Rear Panel – LED .........................................................................................................15
2.2 LED Indications ...................................................................................................................15
2.3 The Rear Panel – Port & Connector ..................................................................................16
2.4 PoE Injector .........................................................................................................................17
Chapter 3. Hardware installation .......................................................................................................18
3.1 Preparation before Installation ..........................................................................................18
3.1.1 Professional Installation Required ..............................................................................18
3.1.2 Safety Precautions......................................................................................................18
3.1.3 Installation Precautions...............................................................................................18
3.2 Hardware Installation .......................................................................................................... 19
3.2.1 Connect Up .................................................................................................................19
3.2.2 Pole Mounting .............................................................................................................22
3.2.3 Using the External Antenna ........................................................................................22
Chapter 4. Software Installation ........................................................................................................23
4.1 Software Configuration.......................................................................................................23
4.2 Connecting the AP .............................................................................................................. 23
4.3 Web Login ............................................................................................................................27
Chapter 5. Basic System Settings.....................................................................................................29
5.1 Setup Wizard .......................................................................................................................29
5.2 Operation Mode................................................................................................................... 36
5.3 Internet Settings.................................................................................................................. 37
5.3.1 WAN............................................................................................................................37
5.3.2 LAN .............................................................................................................................40
5.3.3 DHCP Clients..............................................................................................................42
5.3.4 VPN Passthrough .......................................................................................................42
5.4 Wireless................................................................................................................................43
5.4.1 Basic ...........................................................................................................................43
- 6 -

User’s Manual of WNAP-6305
5.4.2 Advanced ....................................................................................................................45
5.4.3 Security .......................................................................................................................47
5.4.4 WDS............................................................................................................................56
5.4.5 Site Survey..................................................................................................................60
5.4.6 WPS............................................................................................................................64
5.5 Firewall .................................................................................................................................68
5.5.1 MAC /IP /Port Filtering ................................................................................................68
5.5.2 Port Forwarding ..........................................................................................................70
5.5.3 DMZ ............................................................................................................................71
5.5.4 System Security ..........................................................................................................72
5.5.5 Content Filtering..........................................................................................................73
5.6 Administrator....................................................................................................................... 74
5.6.1 Management ...............................................................................................................74
5.6.2 Upload Firmware.........................................................................................................75
5.6.3 Settings Management.................................................................................................76
5.6.4 Status ..........................................................................................................................77
5.6.5 System Log .................................................................................................................78
Appendix A: FAQ.................................................................................................................................79
1. What and how to find my PC’s IP and MAC address? ....................................................79
2. What is Wireless LAN?.......................................................................................................79
3. What are ISM bands? .........................................................................................................79
4. How does wireless networking work?..............................................................................79
5. What is BSSID?................................................................................................................... 80
6. What is ESSID? ................................................................................................................... 80
7. What are potential factors that may causes interference? ............................................80
8. What are the Open System and Shared Key authentications?......................................81
9. What is WEP?......................................................................................................................81
10. What is Fragment Threshold? ........................................................................................... 81
11. What is RTS (Request to Send) Threshold? ....................................................................82
12. What is Beacon Interval? ...................................................................................................82
13. What is Preamble Type?.....................................................................................................82
14. What is SSID Broadcast?................................................................................................... 82
15. What is Wi-Fi Protected Access (WPA)? ..........................................................................83
16. What is WPA2?.................................................................................................................... 83
17. What is 802.1x Authentication?.........................................................................................83
18. What is Temporal Key Integrity Protocol (TKIP)?............................................................83
19. What is Advanced Encryption Standard (AES)? .............................................................83
20. What is Inter-Access Point Protocol (IAPP)?...................................................................83
21. What is Wireless Distribution System (WDS)? ................................................................84
22. What is Universal Plug and Play (UPnP)?........................................................................ 84
- 7 -

User’s Manual of WNAP-6305
23. What is Maximum Transmission Unit (MTU) Size? .........................................................84
24. What is Clone MAC Address? ...........................................................................................84
25. What is DDNS?....................................................................................................................84
26. What is NTP Client?............................................................................................................84
27. What is VPN?....................................................................................................................... 84
28. What is IPSEC? ................................................................................................................... 84
29. What is WLAN Block Relay between Clients? .................................................................85
30. What is WMM?.....................................................................................................................85
31. What is WLAN ACK TIMEOUT? .........................................................................................85
32. What is Modulation Coding Scheme (MCS)?...................................................................85
33. What is Frame Aggregation? ............................................................................................. 85
34. What is Guard Intervals (GI)? ............................................................................................ 85
Appendix B: Configuration Example ................................................................................................86
1. Example – PPPoE on the WAN ............................................................................................86
2. Example – fixed IP on the WAN ...........................................................................................90
3. Example – set WLAN to be WAN as WiFi Client.................................................................94
Appendix C: Specifications................................................................................................................97
Appendix D: Glossary.........................................................................................................................99
- 8 -

User’s Manual of WNAP-6305
Chapter 1. Product Introduction
1.1 Package contents
The following items should be contained in the package:
WNAP-6305 Wireless Outdoor AP
Power Adapter (12V, 1A)
PoE Injector with reset button
Mounting Tie x 2
Quick Installation Guide
CD-ROM (User’s Manual included)
If there is any item missed or damaged, please contact the seller immediately.
1.2 Product Description
The WNAP-6305 is an affordable IEEE 802.11b/g /n specifications of Outdoor Router solution. It
provides a setting of SOHO and enterprise standard for high performance, secure, manageable and
reliable WLAN. This document describes the steps required for the initial IP address assign and other
configuration of the outdoor router.
Faster Speed and Widely Range
Adopting IEEE 802.11n advanced MIMO technology; it provides reliable wireless network coverage,
and incredible improvement in the wireless performance. As an IEEE 802.11b/g/n compliant wireless
device, the WNAP-6305 is able to give stable and efficient wireless performance for long distance
application, while designed with IEEE 802.11n standard and 1T1R MIMO technology makes it possible
to deliver three times faster data rate up to 150Mbps than normal 802.11g wireless device. With its
adjustable output power up to 600mW can extend the higher coverage up to 10Km for outdoor long
range application.
- 9 -

User’s Manual of WNAP-6305
Multiple Operating & Wireless Modes
It supports multiple wireless communication connectivity (AP / Client CPE / WDS PtP / WDS PtMP /
Repeater / Universal Repeater), allowing for various application requirements that gives user more
comprehensive experience when using WNAP-6305. It also helps user easily to build wireless network
and extend the wireless range of existed wireless network.
Advanced Wireless Security
In aspect of security, besides 64/128- bit WEP encryption, the WNAP-6305 integrates WPA / WPA2,
WPA-PSK / WPA2-PSK and 802.1x authority to secure and protect your wireless LAN. The wireless
MAC filtering and SSID broadcast control to consolidate the wireless network security and prevent
unauthorized wireless connection.
Perfect Solution for Outdoor Environment
The WNAP-6305 is perfectly suitable to be installed in outdoor environments and exposed locations.
With its IP-65 casing protection, the WNAP-6305 can perform normally under rigorous weather
conditions including heavy rain and wind. With the proprietary Power over Ethernet (PoE) design, the
WNAP-6305 can be easily installed in the areas where power outlets are not available. It is the best
way using the WNAP-6305 to build outdoor wireless access applications between buildings on
campuses, business, rural areas and etc.
Easy Installation & Management
With User-friendly Web UI and step by step Setup Wizard, it is easier to install, even through a user
who never experiencing setup a wireless network.
- 10 -

User’s Manual of WNAP-6305
1.3 Product Features
Industrial Compliant Wireless LAN & LAN
Compliant with IEEE 802.11n wireless technology capable of up to 150Mbps data rate
Backward compatible with 802.11b/g standard
Equipped with 10/100Mbps RJ-45 Ports for LAN & WAN, Auto MDI/ MDI-X supported
Fixed-network Broadband Router
Supported connection types: Dynamic IP/ Static IP / PPPoE / PPTP / L2TP
Support multiple sessions IPSec, L2TP and PPTP VPN pass-through
Support Virtual Server, DMZ and Port Forwarding for various networking applications
Support DHCP Server, UPnP, Dynamic DNS
RF Interface Characteristics
Built-in 9dBi Directional Antenna
High Output Power Up to 600mWwith multiple adjustable transmit power control
Reserve RP-SMA Type Connector
Outdoor Environmental Characteristics
IP-65 Enclosure, Outdoor UV Stabilized Plastic
Passive Power Over Ethernet Design
Reset Button on PoE Injector
Operating Temperature: -20~70°C
Multiple Operation & Wireless Mode
Multiple Operation Modes: WDS, Gateway, Ethernet Converter
Multiple Wireless Modes: AP, Client CPE(WISP), WDS PtP, WDS PtMP, Repeater,
Universal Repeater
Secure Network Connection
Support Software Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES),
and 802.1x Authentication
Support NAT firewall features, with SPI function to protect against DoS attacks.
Support IP / Protocol-based access control and MAC Filtering
Easy Installation & Management
Web-based UI and Quick Setup Wizard for easy configuration
Remote Management allows configuration from a remote site
System status monitoring includes DHCP Client, System Log
- 11 -

User’s Manual of WNAP-6305
1.4 Product Specification
Product WNAP-6305
150Mbps 802.11n Wireless Outdoor Access Point
Hardware Specification
Standard support
IEEE802.11b/g
IEEE 802.11n
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3x Flow Control
Chipset Ralink RT3050
Memory 16 Mbytes DDR SDRAM
4 Mbytes Flash
Interface
Wireless IEEE802.11b/g/n
LAN: 1 x 10/100Base-TX, Auto-MDI/MDIX
WAN: 1 x 10/100Base-TX, Auto-MDI/MDIX
Antenna
Internal (Default): 9dBi directional antenna (Vertical-Pol)
Horizontal: 60 degree
Vertical: 30 degree
External (Option): RP-SMA type Connector
Switchable by Software
For External Antenna Mode, attach antenna before power on
Enclosure IP55 waterproof case
PoE
Passive PoE / 12V DC
Reset Button on PoE Injector
LAN RJ-45 Pin Assignment: PIN 4(+), PIN 7,8(-), PIN 5(Reset)
Wireless Interface Specification
Frequency Band 2.4~2.4835GHz
Modulation
Transmission/Emission Type: DSSS / OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM,
DBPSK, DQPSK, CCK
Data Rate
802.11b: 11, 5.5, 2 and 1 Mbps with auto-rate fall back
802.11g: 54, 48, 36, 24, 18, 12, 9 and 6Mbps
802.11n (20MHz): up to 72Mbps
802.11n (40MHz): up to 150Mbp
Opt. Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Japan/ TELEC: 2.412~2.484GHz (14 Channels)
RF Output Power
802.11b: 27 ± 1dBm
802.11g: 26 ± 1dBm
802.11n: 22 ± 1dBm
Receiver Sensitivity
IEEE 802.11b: -93dBm
IEEE 802.11g: -91dBm
IEEE 802.11n: -89dBm
Media Access Control CSMA/CA
Output Power Control Range 1~100, default:100
Power Requirements 12V DC, 1A (switching)
Wireless Management Features
Wireless Mode AP
Client
- 12 -

User’s Manual of WNAP-6305
WDS PtP
WDS PtMP
WDS Repeater (AP+WDS)
Universal Repeater (AP+Client)
Channel Width 20MHz / 40MHz
Encryption Security
64/128-bits WEP
WPA, WPA-PSK
WPA2, WPA2-PSK
802.1X
Wireless Isolation Enable it to isolate each connected wireless clients, to let them
cannot access mutually.
Provide wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
Support WPS (WIFI Protected Setup )
Wireless Security
Enable/Disable SSID Broadcast
B/G Protection Mode A protection mechanism prevents collisions among 802.11b/g modes
Max. Wireless Client 25
Max. WDS AP 4
Software
Built-in DHCP server supporting static IP address distributing
Support UPnP
Support IGMP Proxy, DNS Proxy
LAN
Support 802.1d STP - Spanning Tree Protocol
WAN Protocol
Static IP
DHCP (Dynamic IP)
PPPoE
PPTP
L2TP
VPN Passthrough
PPTP
L2TP
IPSec
Operating Mode
Bridge
Gateway
Ethernet Converter (WISP)
NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting Port Forwarding (Virtual Server), and
DMZ
Firewall
Built-in firewall with Port/ IP address/ MAC/ URL filtering
Max. Wired Client 60
NTP Network Time Management
Management Web UI, DHCP Client, Configuration Backup & Restore, Dynamic
DNS
Diagnostic tool System Log
Environment & Certification
Operation Temp. Temp.: -20~70°c, Humidity: 10%~95% non-condensing
Storage Temp. Temp.: -30~80°c, Humidity: 5%~95% non-condensing
IP Level IP-65
Regulatory CE / FCC / RoHS
- 13 -

User’s Manual of WNAP-6305
1.5 Wireless Performance
The following information will help you utilizing the wireless performance, and operating coverage of
WNAP-6305.
1. Site selection
To avoid interferences, please locate WNAP-6305 and wireless clients away from transformers,
microwave ovens, heavy-duty motors, refrigerators, fluorescent lights, and other industrial equipments.
Keep the number of walls, or ceilings between AP and clients as few as possible; otherwise the signal
strength may be seriously reduced. Place WNAP-6305 in open space or add additional WNAP-6305 as
needed to improve the coverage.
2. Environmental factors
The wireless network is easily affected by many environmental factors. Every environment is unique
with different obstacles, construction materials, weather, etc. It is hard to determine the exact operating
range of WNAP-6305 in a specific location without testing.
- 14 -

User’s Manual of WNAP-6305
Chapter 2. Hardware Description
2.1 The Rear Panel – LED
WAN Port LED
LAN Port LED
Wireless LAN LED
Power LED
Figure 2-1 Rear Panel LED Identification
2.2 LED Indications
LED State Meaning
On System On
Power Off System Off
On Wireless Radio ON.
Off Wireless Radio Off.
WLAN
Blinking Data is transmitting or receiving on the wireless.
On Port linked.
Off No link.
WAN
Blinking Data is transmitting or receiving on the WAN interface.
On Port linked.
Off No link.
LAN
Blinking Data is transmitting or receiving on the LAN interface.
- 15 -

User’s Manual of WNAP-6305
2.3 The Rear Panel – Port & Connector
RP-SMA Connector for External Antenna
LAN Port with PoE WAN Port with PoE
Figure 2-2 Port and Connector of WNAP-6305
Figure 2-3 Port and Connector description label
Interface Function
RP-SMA Connector For external antenna. You can use the SMA connector to connect with
2.4GHz external antenna.
LAN
The RJ-45 sockets allow LAN connection through Category 5 cables.
Support auto-sensing on 10/100M speed and half/ full duplex; comply
with IEEE 802.3/ 802.3u respectively.
WAN
The RJ-45 socket allows WAN connection through a Category 5 cable.
Support auto-sensing on 10/100M speed and half/ full duplex; comply
with IEEE 802.3/ 802.3u respectively.
1. For External Antenna Mode, you MUST physically attach antenna before power
on.
2. For using external antenna, you should configure the Antenna Switch from
“Internal” to “External” via Web UI.
- 16 -

User’s Manual of WNAP-6305
2.4 PoE Injector
Hardware Button
Figure 2-4 Top view of PoE Injector
Figure 2-5 Label of PoE Injector
Hardware Button
Reset Button
Figure 2.6 Reset Button of PoE Injector
Active Time
Reset Push continually the reset button of POE injector about 5 ~ 10 seconds to
reset the configuration parameters to factory defaults.
- 17 -

User’s Manual of WNAP-6305
Chapter 3. Hardware installation
This chapter describes safety precautions and product information you have to know and check before
installing WNAP-6305.
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and
knowledgeable in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety
precautions.
2. If you are installing WNAP-6305 for the first time, for your safety as well as others’, please seek
assistance from a professional installer who has received safety training on the hazards
involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially
where there are electric power and phone lines.
4. When installing WNAP-6305, please note the following things:
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present
when the transmitter is on.
3.1.3 Installation Precautions
To keep the WNAP-6305 well while you are installing it, please read and follow these installation
precautions.
1. Users MUST use a proper and well-installed surge arrestor with the WNAP-6305; otherwise, a
random lightening could easily cause fatal damage to WNAP-6305. EMD (Lightning)
DAMAGE IS NOT COVERED UNDER WARRNTY.
2. Users MUST use the “Power cord & PoE Injector” shipped in the box with the WNAP-6305.
Use of other options will cause damage to the WNAP-6305.
3. Users MUST power off the WNAP-6305 first before connecting the external antenna to it.
Do not switch from built-in antenna to the external antenna from WEB management without
physically attaching the external antenna onto the WNAP-6305; otherwise, damage might be
caused to the WNAP-6305 itself.
- 18 -

User’s Manual of WNAP-6305
- 19 -
3.2 Hardware Installation
3.2.1 Connect Up
Step 1. Push the latch in the bottom of WNAP-6305 to remove the sliding cover.
Figure 3-1 Move the cover
Step 2. Plug the RJ-45 Ethernet cable into the LAN Port of WNAP-6305.
Figure 3-2 Cable Connection
RJ-45 8P8C Ethernet cable is required.

User’s Manual of WNAP-6305
Step 3. Slide the cover back to seal the bottom of the WNAP-6305.
Figure 3-3 Seal the bottom
Step 4. Take out the power cord and PoE injector, plug the power cord into the DC port and plug the
other side of the RJ-45 cable in the STEP 2 into the POE port of the PoE injector.
DC: Insert adapter
POE: This hole is linked to LAN port of the Outdoor Router with RJ-45.
LAN: This hole is linked to LAN side PC/Hub or Router/ADSL modem device with RJ-45
Figure 3-4 Connect to PoE Injector
- 20 -