Planet WNAP-3000PE User manual

802.11n Enterprise PoE Access Point
WNAP-3000PE
Quick Installation Guide

Table of Contents
Package Content.............................................................................................. 3
Physical Details................................................................................................ 4
Front panel ................................................................................................ 4
LED denition............................................................................................. 4
Back Panel ................................................................................................ 5
Hardware Installation ....................................................................................... 6
General installation ..................................................................................... 6
PoE installation........................................................................................... 6
Web Conguration ........................................................................................... 7
Further Conguration ....................................................................................... 8

3
Package Content
WNAP-3000PE x 1
2dBi Dipole Antenna x 3
Power Adapter x 1
Quick Installation Guide x 1
CD-ROM x 1
Note
If any of the above items are missing or damaged, contact your
local dealer for support.
l
l
l
l
l

4
Physical Details
Front panel
LED denition
Power On - Normal operation.
Off - No power
WLAN
On - Idle
Off - Wireless connection is not available.
Flashing - Data is being transmitted or received via the Wireless
access point. Data includes “network trafc” as well as
user data.
Status
On - Error condition.
Off - Normal operation.
Blinking - During start up, and when the Firmware is being
upgraded.
LAN
On - The LAN port is active.
Off - No active connection on the LAN port.
Flashing - Data is being transmitted or received via the
corresponding LAN port.

5
Back Panel
Reset Button
This button has two (2) functions:
Reboot - When pressed and released, the Wireless Access
Point will reboot (restart).
Reset to Factory Defaults - This button can also be used to
clear ALL data and restore ALL settings to the factory default
values.
To Clear All Data and restore the factory default values:
1. Hold the Reset Button until the Status (Red) LED blinks
TWICE, usually more than 5 seconds.
2. Release the Reset Button.
The factory default conguration has now been restored,
and the Access Point is ready for use.
LAN Use a standard LAN cable (RJ45 connectors) to connect this
port to a 10/100/1000BaseT hub/switch on your LAN.
Power Connect the supplied power adapter (12VDC @1A) here.

6
Hardware Installation
General installation
1. Locate an optimum location for the WNAP-3000PE. The best place for your
WNAP-3000PE is usually at the center of your wireless network, with line of sight
to all of your mobile stations.
2. Assemble the antennas to WNAP-3000PE. Try to place them to a position
that can best cover your wireless network. The antenna’s position will enhance
the receiving sensitivity.
3. Connect RJ-45 cable to WNAP-3000PE. Connect the “LAN” port of WNAP-
3000PE to your LAN switch/hub or a single PC.
4. Plug in power adapter and connect to power source. After power on,
WNAP-3000PE will start to operate.
5. Check the LEDs:
The Status LED should ash, then turn OFF.
The Power, Ethernet and WLAN LEDs should be ON.
For more information, please refer to LED deication.
Note
1. ONLY use the power adapter supplied with the WNAP-3000PE.
Otherwise, the product may be damaged.
2. Use only one power source for WNAP-3000PE, use of both
power sources, i.e. 12VDC and 802.3af PoE, at the same time
may cause the device faulty.
PoE installation
1. Do not connect the supplied power adapter to the WNAP-3000PE.
2. Connect one end of a standard (category 5) LAN cable to the Ethernet port on
the WNAP-3000PE.
3. Connect the other end of the LAN cable to the powered Ethernet port on a suit-
able PoE Adapter or switch. (IEEE 802.3af compliant)
4. Connect the unpowered Ethernet port on the PoE adapter to your Hub or switch.
5. Connect the power supply to the PoE adapter and power up.
6. Check the LEDs on the WNAP-3000PE to see it is drawing power via the Ethernet
connection.
l
l

7
Web Conguration
WNAP-3000PE provides a user friendly interface for users to congure it via web
browser. Please follow the steps below to congure WNAP-3000PE basic settings.
1. The default value of WNAP-3000PE doesn’t enable DHCP server, please
double check obtain the IP from DHCP server in your network, otherwise,
please congure static IP address in your PC to an unused value in the range
192.168.0.1 ~ 192.168.0.254, with a Network Mask of 255.255.255.0.
2. Open your web browser and type WNAP-3000PE default IP address
http://192.168.0.228 into the “Address Field” of you web browser.
3. After enter the IP address and press Enter key, you can see the dialog box
appear as below, please enter the User name and Password. Then press “OK”.
User name: admin
Password: password

8
Further Conguration
If you want to congure WNAP-3000PE with more detail settings, please refer to
our manual in the CD-ROM and congure with your Web Browser. If you have any
difculty on resolving the problem while installing or using WNAP-3000PE, please
contact with your local dialer or feel free to contact PLANET for support.