Planet WNAP-6350 User manual

User’s Manual
www.PLANET.com.tw
802.11b/g/n Wireless Outdoor AP
WNAP-6350

Copyright
Copyright 2013 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
nt. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own
expense. Any changes or modifications not expressly approved by PLANET could void the user’s
authority to operate this equipment under the rules and regulations of the FCC.
environme
FCC Caution:
To assure continued compliance, (example-use only shielded interface cables when connecting to
computer or peripheral devices) any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may cause
undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
I

CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the DC-plug to disconnect the device from the power circuit.
Without remove the DC-plug, the device still consuming power from the power circuit. In the view of
Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to
remove the DC-plug for the device if this device is not intended to be active.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications
Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
II

Revision
User’s Manual for PLANET 802.11b/g/n Wireless Outdoor Access Point
Model: WNAP-6350
Rev: 2.0 (August, 2013)
Part No. EM-WNAP-6350_v2.0 (2081-E10510-003)
III

CONTENTS
Chapter 1.Product Introduction...........................................................................................................1
1.1 Package Contents ...............................................................................................................1
1.2 Product Description............................................................................................................ 2
1.3 Product Features................................................................................................................. 6
1.4 Product Specifications .......................................................................................................7
Chapter 2.Hardware Installation ........................................................................................................ 10
2.1 Hardware Description ....................................................................................................... 10
2.1.1 The Bottom Panel...................................................................................................10
Chapter 3.Connecting to the AP ........................................................................................................12
3.1 Preparation before Installation ........................................................................................12
3.1.1 Professional Installation Required ..........................................................................12
3.1.2 Safety Precautions..................................................................................................12
3.2 Installation Precautions....................................................................................................12
3.3 Installing the AP ................................................................................................................14
Chapter 4.Quick Installation Guide ...................................................................................................17
4.1 Manual Network Setup - TCP/IP Configuration ..............................................................17
4.1.1 Configuring the IP Address Manually .....................................................................17
4.2 Starting Setup in the Web UI............................................................................................ 21
Chapter 5.Configuring the AP............................................................................................................ 23
5.1 Status..................................................................................................................................23
5.2 Easy Setup.........................................................................................................................26
5.3 Advanced ...........................................................................................................................27
5.3.1 Advanced - Management........................................................................................27
5.3.1.1. Web Interface Settings (Password)................................................................................ 28
5.3.1.2. Firmware Upgrade ......................................................................................................... 28
5.3.1.3. Configuration.................................................................................................................. 29
5.3.1.4. Load Factory Defaults.................................................................................................... 30
5.3.1.5. Reboot System .............................................................................................................. 30
5.3.1.6. Scheduling Reboot......................................................................................................... 31
5.3.2 Advanced – Advanced Settings..............................................................................31
5.3.2.1. Time Zone Settings ........................................................................................................ 32
5.3.2.2. DDNS Settings............................................................................................................... 32
5.3.2.3. UPNP Settings ............................................................................................................... 34
5.3.2.4. SNMP Settings............................................................................................................... 35
5.3.3 Advanced – Operation Mode..................................................................................36
5.3.3.1. AP Router (AP+Router) ................................................................................................. 36
5.3.3.2. AP Bridge (AP+WDS) .................................................................................................... 37
5.3.3.3. Client Router (WISP) ..................................................................................................... 38
IV

5.3.3.4. Client Bridge (Slave AP Bridge) ..................................................................................... 43
5.3.4 Advanced – System Log.........................................................................................43
5.3.5 Advanced – Tools ...................................................................................................44
5.3.5.1. Ping................................................................................................................................44
5.3.5.2. Traceroute...................................................................................................................... 45
5.3.5.3. Throughput..................................................................................................................... 45
5.4 Firewall Settings................................................................................................................46
5.4.1 MAC/IP/Port Filtering..............................................................................................46
5.4.2 Virtual Server ..........................................................................................................47
5.4.3 DMZ ........................................................................................................................48
5.4.4 Firewall....................................................................................................................49
5.4.5 QoS.........................................................................................................................50
5.4.6 Content Filtering .....................................................................................................51
5.4.6.1. Webs URL Filter Settings............................................................................................... 51
5.4.6.2. Web Host Filter Settings ................................................................................................ 52
5.5 Network Settings...............................................................................................................52
5.5.1 WAN........................................................................................................................52
5.5.1.1. Static (Fixed IP).............................................................................................................. 53
5.5.1.2. Cable/Dynamic IP (DHCP)............................................................................................. 54
5.5.1.3. PPPoE (ADSL)............................................................................................................... 54
5.5.1.4. IPSEC ............................................................................................................................ 55
5.5.1.5. PPTP ............................................................................................................................. 59
5.5.1.6. L2TP .............................................................................................................................. 60
5.5.2 LAN.........................................................................................................................61
5.5.2.1. DHCP Server ................................................................................................................. 62
5.5.2.2. DHCP Relay................................................................................................................... 62
5.5.3 VLAN.......................................................................................................................63
5.5.4 Advanced Routing ..................................................................................................64
5.5.5 IPv6.........................................................................................................................65
5.6 Wireless Settings ..............................................................................................................66
5.6.1 Basic .......................................................................................................................66
5.6.1.1. Wireless Mode – Access Point....................................................................................... 67
5.6.1.2. Wireless Mode – WDS Access Point ............................................................................. 69
5.6.1.3. Wireless Mode – WDS Repeater ................................................................................... 71
5.6.1.4. Wireless Mode – WDS Client......................................................................................... 73
5.6.2 Profile Settings........................................................................................................75
5.6.3 Advanced................................................................................................................77
5.6.4 Access Control........................................................................................................78
5.7 Logout ................................................................................................................................79
Appendix A: FAQ.................................................................................................................................80
1. What and how to find my PC’s IP and MAC address? ..................................................80
V

VI
2. What is Wireless LAN? .....................................................................................................80
3. What are ISM bands?........................................................................................................80
4. How does wireless networking work?............................................................................80
5. What is BSSID? .................................................................................................................81
6. What is ESSID? .................................................................................................................81
7. What are potential factors that may cause interference?............................................. 81
8. What are the Open System and Shared Key authentications? ....................................82
9. What is WEP? ....................................................................................................................82
10. What is Fragment Threshold? .........................................................................................82
11. What is RTS (Request to Send) Threshold?...................................................................83
12. What is Beacon Interval? ................................................................................................. 83
13. What is Preamble Type?................................................................................................... 83
14. What is SSID Broadcast? ................................................................................................. 83
15. What is Wi-Fi Protected Access (WPA)?.........................................................................84
16. What is WPA2? ..................................................................................................................84
17. What is 802.1x Authentication? .......................................................................................84
18. What is Temporal Key Integrity Protocol (TKIP)? ..........................................................84
19. What is Advanced Encryption Standard (AES)?............................................................ 84
20. What is Inter-Access Point Protocol (IAPP)?.................................................................84
21. What is Wireless Distribution System (WDS)? ..............................................................85
22. What is Universal Plug and Play (UPnP)? ...................................................................... 85
23. What is Maximum Transmission Unit (MTU) Size?........................................................85
24. What is Clone MAC Address?..........................................................................................85
25. What is DDNS? ..................................................................................................................85
26. What is NTP Client? ..........................................................................................................85
27. What is VPN?..................................................................................................................... 85
28. What is IPSEC? .................................................................................................................85
29. What is WLAN Block Relay between Clients? ...............................................................86
30. What is WMM?................................................................................................................... 86
31. What is WLAN ACK TIMEOUT? .......................................................................................86
32. What is Modulation Coding Scheme (MCS)? .................................................................86
33. What is Frame Aggregation? ...........................................................................................86
34. What is Guard Intervals (GI)?...........................................................................................86
Appendix B: Configuring the PC in Windows 7...............................................................................87
Appendix C: Use Planet Smart Discovery to find AP......................................................................90
Appendix D: Specifications................................................................................................................91

User Manual of WNAP-6350
-1-
Chapter 1.Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WNAP-6350. Before installing the AP, please verify the contents inside the
package box.
WNAP-6350 Wireless AP Quick Installation Guide CD-ROM
(User Manual included)
PoE Injector & Power Cord Mounting Kit x 1 RJ-45 Waterproof Kit x 2
If there is any item missing or damaged, please contact the seller
immediately.

User Manual of WNAP-6350
-2-
1.2 Product Description
High Power Outdoor Wireless Coverage
PLANET Technology introduces the latest high power outdoor wireless LAN solution – the WNAP-6350
300Mbps PoE wireless outdoor AP. It provides higher transmit power, better performance, wide coverage
and more stable connection than standard wireless outdoor AP. As an IEEE 802.11b/g/n compliant wireless
device, the WNAP-6350 is able to give stable and efficient wireless performance for long distance application.
Adopting the IEEE 802.11n standard and 2T2R MIMO technology, the WNAP-6350 is able to deliver six times
faster data rate up to 300Mbps than the normal 802.11g wireless device. It also features adjustable output
power up to 800mW to extend broader coverage in outdoor long range application.
Antenna
Antenna
WNAP-6350
Antenna
WNAP-6350
Antenna
WNAP-6350
Antenna
WNAP-6350
WNAP-6350
Wi-Fi City
2.4GHz 802.11n
N
N
NN
N
N
N

User Manual of WNAP-6350
-3-
The WNAP-6350 supports multiple types of wireless communication connectivities (AP, Client CPE, WDS PtP,
WDS PtMP, Repeater) meeting various application requirements and thus it gives users more comprehensive
experience when accessing through wireless LAN. It helps users to easily build a wireless network and extend
the wireless range of existing wireless network.
The WNAP-6350 also supports WISP mode, so CPE users can easily connect to Internet via WISP provider or
connect to a wired network.
Advanced Security and Management
In aspect of security, besides 64-/128-bit WEP encryption, the WNAP-6350 is integrated with WPA/WPA2,
WPA-PSK/WPA2-PSK and 802.1x authority to secure and protect your wireless LAN. The wireless MAC
filtering and SSID broadcast control consolidate the wireless network security and prevent unauthorized
wireless connection. To fulfill enterprise and various applications demand, the WNAP-6350 also provides
multiple SSIDs to enhance security and management.
Perfect Solution for Outdoor Environment
The WNAP-6350 is perfectly suitable for outdoor environments and exposed locations. With its IP67 aluminum
rugged strong housing, the WNAP-6350 can perform normally under rigorous weather conditions including
heavy rain, wind and snow. Moreover, the WNAP-6350 is rated to operate at the temperature from -30 to 75
degree C; thus, it can operate more stably than general outdoor equipment. It is the best way to use the
Clients
Switch
LAN
AP/Client Mode
Antenna Antenna
WNAP-6350WNAP-6350
AP Mode Client Mode
Internet
WDS Repeater Mode
Internet
WDS Repeater Mode
Clients
Switch
Antenna
WNAP-6350
Antenna
WDS Bridge-PtP Mode
Antenna Antenna
WNAP-6350WNAP-6350
Switch
Clients
Client
Client
Switch Bridge - PtP Mode
Clients
WDS Bridge-PtMP Mode
Switch
Clients
Clients
Switch
Switch
Antenna
Antenna
WNAP-6350
Bridge - PtMP Mode
Internet
WISP Mode
Wireless Internet
Service Provider
Antenna
WNAP-6350
WISP Mode
Relay Mode
Antenna Antenna
WNAP-6350
WNAP-6350
Bridge - Relay Mode
Antenna
Antenna
PoE
PoE
PoE
PoE
PoE
PoE
PoE
WAN
Clients
NN
N
N
N
N
N N
N
N
N
N
N
N
Antenna
N
Multiple Operating & Wireless Modes

User Manual of WNAP-6350
-4-
WNAP-6350 to build outdoor wireless access applications between buildings on campuses, business, rural
areas and more.
Flexible Deployment with PoE Feature
Compliant with IEEE 802.3af/at Power over Ethernet standard, the WNAP-6350 can be powered by PSE
(Power Sourcing Equipment) via a single UTP cable. It thus reduces the needs of extra cables and dedicated
electrical outlets on the wall, ceiling or any other difficult-to-reach places. Furthermore, the WNAP-6350 is also
suitable for being integrated with PoE Solar Power System to offer farther wireless service in remote areas. It
enables the wireless LAN deployment to become more flexible in powering without the power outlet.

User Manual of WNAP-6350
-5-
Easy Installation and Management
With user-friendly Web UI and step by step Setup Wizard, the WNAP-6350 is easy to install, even for users
who never experience setting up a wireless network. Furthermore, with SNMP-based management interface,
the WNAP-6350 is convenient to be managed and configured remotely.

User Manual of WNAP-6350
-6-
1.3 Product Features
Industrial Compliant Wireless LAN & LAN
Compliant with IEEE 802.11n wireless technology capable of up to 300Mbps data rate
Backward compatible with 802.11b/g standard
Equipped with 10/100Mbps RJ-45 Ports for LAN & WAN, Auto MDI / MDI-X supported
Fixed-network Broadband Router
Supported connection types: Dynamic IP / Static IP / PPPoE / PPTP / L2TP / IPSec
Supports Virtual Server, DMZ for various networking applications
Supports DHCP Server, UPnP, Dynamic DNS
RF Interface Characteristics
Built-in two N-Type Female Antenna connectors
High Output Power up to 800mW with multiple adjustable transmit power control
Outdoor Environmental Characteristics
Aluminum Housing, IP67 Protection
IEEE 802.3af/at Power over Ethernet design
Operating Temperature: -30~75 degrees C
Multiple Operation & Wireless Mode
Multiple Operation Modes: Bridge, Gateway, WISP
Multiple Wireless Modes: AP, Client CPE (WISP), WDS PtP, WDS PtMP, Repeater
Supports Dual-SSID allowing users to access different networks through one single AP
Supports WMM (Wi-Fi Multimedia)
Secure Network Connection
Supports Software Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK (TKIP/AES), and
802.1x Authentication
Supports NAT firewall features with SPI function to protect against DoS attacks
Supports IP/Protocol-based access control and MAC filtering
Easy Installation & Management
Web-based UI and Quick Setup Wizard for easy configuration
Remote Management allows configuration from a remote site
SNMP-Based management interface
System status monitoring includes DHCP Client, System Log

User Manual of WNAP-6350
-7-
1.4 Product Specifications
Product WNAP-6350
2.4GHz 300Mbps 802.11n Wireless Outdoor Access Point
Hardware Specifications
Standard
IEEE 802.11b/g/n Wireless LAN
IEEE 802.11i Wireless Security
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af/at Power over Ethernet / PD
Memory 32 Mbytes DDR SDRAM
8 Mbytes Flash
Interface
Wireless IEEE 802.11b/g/n, 2T2R
LAN: 1 x 10/100Base-TX, Auto-MDI / MDIX, IEEE 802.3af/at PoE / PD port
WAN: 1 x 10/100Base-TX, Auto-MDI / MDIX
Antenna N-Type Female connectors x 2
Wireless RF Specifications
Wireless Technology IEEE 802.11b/g
IEEE 802.11n
Data Rate
IEEE 802.11b: 11, 5.5, 2 and 1Mbps
IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9 and 6Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbp
Media Access Control CSMA / CA
Modulation
Transmission/Emission Type: DSSS / OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM,
DBPSK, DQPSK, CCK
Frequency Band 2.412GHz ~ 2.484GHz
Operating Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Japan/ TELEC: 2.412~2.484GHz (14 Channels)
RF Output Power (Max.) IEEE 802.11b/g: 29 ± 1.5dBm
IEEE 802.11n: 25 ± 1.5dBm
Receiver Sensitivity
IEEE 802.11b: -95/ -94/ -92/ -90dBm (1/ 2/ 5.5/ 11Mbps)
IEEE 802.11g: -90/ -82/ -80/ -75dBm (6/ 24/ 36/ 54Mbps)
IEEE 802.11n: -91/ -83/ -74/ -89/ -80/ -72dBm (MCS 0/ 3/ 6/ 9/ 12/ 15)
Output Power Control 3~29dBm
Software Features
Built-in DHCP server supporting static IP address distributing
LAN Supports 802.1d STP (Spanning Tree)
WAN
Static IP
Dynamic IP
PPPoE

User Manual of WNAP-6350
-8-
PPTP
L2TP
IPSec
Operating Mode
Bridge
Gateway
WISP
NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting Virtual Server and DMZ
Firewall
Built-in firewall with Port / IP address / MAC / URL filtering
Wireless Mode
AP
Client
WDS PTP
WDS PTMP
WDS Repeater (AP+WDS)
Channel Width 20MHz / 40MHz
Wireless Isolation Enables isolation of each connected wireless client from communicating with
each other mutually.
Encryption Type 64/128-bits WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Provides wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
Supports WPS (Wi-Fi Protected Setup )
Wireless Security
Enable / Disable SSID Broadcast
Multiple SSID Up to 2
Max. Wireless Client 40
Max. WDS AP 8
Max. Wired Client 60
WMM Supports Wi-Fi Multimedia
QoS Supports Quality of Service for bandwidth control
NTP Network Time Management
Management Web UI, DHCP Client, Configuration Backup & Restore, Dynamic DNS, SNMP
Diagnostic tool System Log, Ping Watchdog
Mechanical & Power
IP Rate IP67
Material Aluminum
Dimensions (W x D x H) 320 x 27.5 x 320 mm
Weight 2.4kg
Installation Pole mounting or Wall mounting
Power Requirements AP: IEEE 802.3af/at PoE / 48VDC input (PoE Injector included)
PoE Injector: 100~240VAC
Power Consumption 7.68W
Environment & Certification
Operation Temperature -30~75 degrees C
Operating Humidity 10~95% non-condensing

User Manual of WNAP-6350
-9-
Regulatory CE / RoHS
Accessory
Standard Accessories
48VDC IEEE 802.3af PoE injector & Power cord x 1
Mounting Kit x 1
Waterproof RJ-45 Connector Kit x 2
Quick Installation Guide x 1
CD (User’s Manual, Quick Installation Guide) x 1

User Manual of WNAP-6350
-10-
Chapter 2.Hardware Installation
Please follow the instructions below to connect the WNAP-6350 to the existing network devices and your
computers.
2.1 Hardware Description
Dimensions: 320 x 27.5 x 320 mm (W x D x H)
Figure 2-1 Three-way View
2.1.1 The Bottom Panel
The bottom panel provides the physical connectors connected to the power adapter and any other network
device. Figure 2-2 shows the bottom panel of the WNAP-6350.

User Manual of WNAP-6350
-11-
Bottom Panel
Figure 2-2 Bottom Panel
Interface Description
LAN
(802.3af/at PoE/PD port)
10/100Mbps RJ-45 port , Auto MDI/ MDI-X & 802.3af/at PoE supported
Connect LAN port to the PoE injector or PoE switch to power on the
device.
N-Type (F)
N-Type Female Antenna Connectors.
Connect N-Type (F) Antenna Connectors with Outdoor Antenna through
the N-Type (Male) to N-Type (Male) RF cable.
WAN / LAN
10/100Mbps RJ-45 port , Auto MDI/ MDI-X
Connect this port to the xDSL modem in AP mode.
Connect this port to the network equipment in bridge mode.
Table 2-1 The Interface indication

User Manual of WNAP-6350
-12-
Chapter 3.Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable
in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety precautions.
2. If you are installing the WNAP-6350 for the first time, for your safety as well as others’, please seek
assistance from a professional installer who has received safety training on the hazards involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.
4. When installing the WNAP-6350, please note the following things:
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.
3.2 Installation Precautions
Users MUST use a proper and well-installed surge arrestor and grounding kit with the WNAP-6350;
otherwise, a random lightning could easily cause fatal damage to the WNAP-6350. EMD (Lightning)
DAMAGE IS NOT COVERED UNDER WARRANTY.
Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-6350. Use of
other options will cause damage to the WNAP-6350.
Users MUST power off the WNAP-6350 first before connecting the external antennas to it; otherwise,
damage might be caused to the WNAP-6350 itself.

User Manual of WNAP-6350
-13-
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the
equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power
lines are anywhere where possible contact can be made. Antennas, masts,
towers, guy wires or cables may lean or fall and contact these lines. People
may be injured or killed if they are touching or holding any part of
equipment when it contacts electric lines. Make sure there is NO possibility
that equipment or personnel can come in contact directly or indirectly with
power lines.
Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of
the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
!
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static
build-up, or short circuit within equipment connected to the antenna.
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 10 AWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.